Konlen KL-P103 User manual

GPS\GSM fleet management tracking system www.konlen.com
1-18
GPS/GPRS/GSM vehicle tracker
KL-P103
USER MANUAL
VER ：
：：
： KL091005

GPS\GSM fleet management tracking system www.konlen.com
2-18
Ⅰ
ⅠⅠ
ⅠInstruction
KL-P103 satellite positioning system combines with anti-theft, positioning, listen-in, monitoring, tracking,
emergency help, vehicle scheduling, image capture and platform software management etc.functions. With
the full-featured characteristics, it widely applies to vehicles and other mobile object location and tracking
services, large-scale cluster monitoring, emergency scheduling, traffic safety management and many other
fields.
1.1 Funtion and Features
Locating and tracking in real time
Positioning call/Track playback/listen-in
Camera photo taking
Mileage statistic
Cut off the oil / recovery circuit
Overspeeding alarm
Parking overtime alarm
Fatigue driving alarm
Idle time-out alarm
User self definiton alarm
Emergency help alarm
Main power off alarm
Enter or exit the electronic fence alarm
The designated route deviate warning
GPS antenna short circuit, open circuit alarm
TCP/UDP/SMS transmission mode
GSM blind area data memory and re-uploading
Auto-sleeping mode saves GPRS flow
Data automatic upload: as per time interval/distance interval
Remote control and inquiry terminal via SMS and software
External device: camera for image capture
Free to air firmware upgrade(for new features upgrade)

GPS\GSM fleet management tracking system www.konlen.com
3-18
1.2 Specification
NAME PARAMETER
Main device dimension 85mm × 55mm × 29mm
Main device weight 0.18kgs
Color Black
Working voltage 12V -- 24V DC
Working current 80mA, 200mA (12V/DC)
Back-up battery 300mA / H
Working temperature -35℃-- 85℃
Moisture 5% -- 95%（Non-water vapor condensation state）
CPU ARM7 main frequency 60MHZ
Flash 2MB(can expand as per customer’s requirement)
Picture storage 30pcs (can expand as per customer’s requirement
Uploading picture speed 20s to 50s
camera Support one rout of camera
GSM Frequency 900MHz / 1800 MHz / 850MHz / 1900 MHz
GPS Module Latest U-BLOX locating module
GPS Sensitivity -159Dbm
GPS Frequency Baud rate
Receiving panel structure
GPS module 24-channel
Locating accuracy < 5m （95％）
Time update Synchronize with GPS
Cold start time < 36s(in average）
Heat start time < 1 s (in average）
LED indicator light Dual-color LED indicator light (green and red)shows the GPS / GSM status
1.3 Packing List
NAME QTY IMAGE Remark
Main device 1PCS /
GSM Antenna 1PCS Receiving GSM network signal
GPS Antenna 1PCS Receiving satellite locating signal data

GPS\GSM fleet management tracking system www.konlen.com
4-18
Circuit
beaker(relay) 1PCS
Fuel-break/ power off
DC12v or DC24v (optional)
MIC 1PCS Listen in
6PIN cables with
SOS button 1PCS
Installation cable: match the 6PIN cable
socket(B6B) with tracker 103A6A; the other end
connecting with automobile circuit.
Binding cables 3PCS ／For fixing main device and cables
Double sticker 2PCS ／For fixing main device and cables
User manual 1 PCS ／/
Camera 1PCS For picture capture (Optional)
1.4 Indicator light definition
NOTE: The line in green in chart means works normally and in standby status.
LED color
Light on Light off Status description
green 0.5s 0.5s In starting status
green 1s 1 s Failed to search for GPS satellite signal,unlocated
green 5 s 0.5 s Found GPS satellite signals, located
green Light off Light off Device power failed or LED indicator light fault
red 1 s 1 s Searching for GSM network signal
red 0.5 s 3 s GSM network signal normal
red Flash fast 0.5 s Device is transferring the GPRS data
red Light off Light off Equipment no power or LED indicator lights faults
red Light on 1.Telephone dial in or dial out 2. Tracker is rebooting

GPS\GSM fleet management tracking system www.konlen.com
5-18
Ⅱ
ⅡⅡ
Ⅱ Main device installtion
Note: This product is not waterproof. Please choose the dry location to install.
2.1 Main device diagram
1. Main device 2. SIM card slot
3. Rear cover of main device 4. Back-up battery switch
5. Main device side 6. Main device ID No.
7. Main device side 8. GSM antenna connector
9. GPS antenna connector 10. Main device front panel
11. Cable installation hole 12. Double color LED light
13. MIC connector
103A6A: 6 Pin installation cable:
103A3A: For User self-defined alarm(one anode trigger and one cathode trigger) and device updating
103A4A: External device serial port, support one rout of camera or overspeed alarm buzzer etc.
2.2 SIM card installation
A. Take off the rear cover of main device by screwdriver
B. Install the SIM card as below steps.
（Step 1）（Step 2）（Step 3）
C. Connect external power supply and turn on the backup battery after installing the SIM card.
Note:
a. Make sure the SIM card can make phone call, receive & sending SMS.
b. Make sure the SIM card with enough money and can access to GPRS internet function.

GPS\GSM fleet management tracking system www.konlen.com
6-18
c. The SIM card must support voice call function if need listen in the voice at site.
d. Make sure to insert and take off SIM card in power off status, or it is easy to burn the SIM card
and device. Please install the SIM card first before turn on the backup battery or connect the external
power, and take off the SIM card after turn off the backup battery and external power.
2.3 103A6A/103B6B Installation wiring diagram
a. Insert 103 A6A connector into 103B6B 6PIN cable socket first.
b. The white socket of 103B6B with total 6 wires. Except for the two cables for emergency button, there
are another 4 cables , red, black, white andYellow.
Please connect the red wire (+) and black wire (-) with the car battery (the main power);
Connect white wire with ACC for checkingACC status, on or off.
The yellow wire with the Circuit Breaker for Oil cut off /power off)
c. Please install the emergency button in hiden place but convenience for driver to operate. Make sure no
any objects press the button, or it will always send emergency alert to monitoring center.
d. Please make sure to connect the trackers with vehicle main power (car battery) correctly and turn on the
tracker backup battery to avoid the tracker no power and can not know the vehicle status.
2.4 The Circuit breaker(relay) wiring connection.
The relay with four wires, two green(signal wire), white(+) and yellow(-).
The yellow wire connects with B6B yellow wire
The two green wire and white wire connect with Engine as below.
Cut the engine wire, connect one green wire and the white wire together with one end of cutted engine

GPS\GSM fleet management tracking system www.konlen.com
7-18
wire(currect passing direction), and connect the other green wire with the other end.
2.5 103A3A installation diagram
103A3A with three wires, red (+), green(-), orange(signal wire). The green and red are user self-definiton
alarm trigger wires, the green for user-defined 1 trigger alarm(anode trigger), the red for user-defined 2
trigger alarm(cathode trigger).
User can install the two wire for detecting illegal door/cover open if need to monitor the car door, engine
cover, car trunk, taximeter etc.User need add wired door contact (NO) additionally if the door or cover
without contact switch. The below is the wiring diagram about how to connect wired door contact with
103A3A green or red wire.
Note:The 103A3A can also use for tracker updating
2.6 103A4A and camera installation.
The 103A4A is a serial port with 4Pin cables that can connect camera. Factory will provide user a
additional cable with connector each end. One end connects with 103A4A, the other end connect with
camera. Please choose the correct installation location of camera according to actual application and
different vehicle types.
3.6 GPS/GSM antenna installing .
Note:
1. Prolong the GSM antenna as possilbe as you can.
2. Don’t install the GPS antenna close to the objects which generate strong signal interference, such as
radio, car circuit, speaker, air-conditioning etc.
3. Install the GPS antenna in a hidden place. The black side of GPS antenna must face up and no metal
Green User-defined 1 trigger alarm
Red User-defined 2 trigger alarm

GPS\GSM fleet management tracking system www.konlen.com
8-18
shielding material cover it within 60 degree range. Please don’t leave after installation until the GPS fleet
management platform can receive location datas normally and stably for 5 minutes at least.
The below is suggested GPS antenna installation locatation
Ⅲ
ⅢⅢ
ⅢOperation
3.1 Quick guidline of operation
a. Install SIM card following 3.2 guid above, then connect external power 12V.
b. Set GPS tracker by SMS or software, such as IP, Port, and APN etc. so that trackes can link with
software via GPRS.
c. Add the GPS tracker into the software as per software manual, then check whether the tracker is online.
If the tracker online, that means all the set is correct and tracker is OK.
d. Install the tracker in the vehicle as per installation instruction.
e. After installation, please check whether the tracker is online, whether download and update the GPS
data normally.
f. Manage all the added GPS trackers via software. About software operation, please read software fleet
platform management manual.
User can set, modify the parameter of GPS tracker and inquiry its status via SMS or software as below.
a.The junction of windscreen wiper and front cover: ①
b. The gap in the middle of car proof: ② ④
c. Under instrument desk: ③
d. The junction of rear windshield: ⑤

GPS\GSM fleet management tracking system www.konlen.com
9-18
3.2 SMS Setting
NO
IUSSE SEND COMMAND ANSWER COMMAND REMARK
1 SET SERVER IP AND
PORT AS1234IPPO:119.147.23.108;7777
；# IPPO:119.147.23.108;7777,26339788;OK
Response content is “IP””Port” “Current Device ID”
2 SET TERMINAL ID AS1234IDDO:26339788# IDDO:26339788;OK Response Current Device “ID”
3 A
P
N
Access Point Name AS1234APN:CMNET# APN:CMNET;OK At most 39 Character
4 APN user name AS1234USER:USER# USER:USER;OK At most 39 Character
5 APN password AS1234GPRSPASS:GPRS# GPRSPASS:GPRS;OK At most 39 Character
6 Restart Device AS1234RSGS# GSM/restart; OK Device Restart
7 Factory Reset Keep in secret / Please consult your supplier if neet do it.
8 Device Status Enquiry AS1234STATE#
ID:99999999 VER:V1.05
IP:119.147.23.108,7777 CEN: AUT:
CSQ:19 GPS:OK ACC:ON GPRS:30
POWER:ON NETTYPE:GPRS
1、ID：Current Device ID
2、Ver：Current firmware version
3、IP：Current IP and Port
4、CSQ：Current GSM signal strength
5、GPS：GPS available or not
6、ACC：Current ACC status
7、GPRS：Current GPRS data upload interval
8、POWER：Current Power status
9、NETTYPE：Current Communicate mode
9 Open/Close
Standby sleeping Mode AS1234WAKEUP:5＃WAKEUP:5 1、Unit：“minute”；
2、Type and range：“0” Close；1~1440:sleep for this
time and wakeup for 25minutes.
10 Awake up Device AS1234SLEEP:# SLEEP:OFF Temp exit sleeping mode, will sleep again after
25min
Standard function
1 Communicate Mode Set AS1234SMGP:0＃
AS1234SMGP:1＃
AS1234SMGP:2＃
SMGP:UDP;OK
SMGP:TCP;OK
SMGP:SMS;OK
1、“0”UDP Mode；
2、“1”TCP Mode；
3.、“2”SMS Mode
2 Control Center Number Set
AS1234HOME:13510642316＃
AS1234HOME:0＃HOME:13510642316;OK
HOME:CLEAR;OK

GPS\GSM fleet management tracking system www.konlen.com
10-18
3 Authorized Number Set AS1234EMPOWER:13590251897#
AS1234EMPOWER:0# EMPOWER:13590251897;OK EMPOWER: CLEAR;OK
4 Change Device Password AS1234PASSWORD:5678# PASSWORD:5678;OK
5 Track Once AS1234WHERE# TRACK:Latitude:+22.123456;Longtitude
:+113.123456;speed:98;ACC:ON Send once
6 SET TRACK Interval (send to Control Center
only)
AS1234TRACK:3#
AS1234TRACK:0#
Track:3;OK
Track:OFF;OK
Data upload format ：
TRACK:Latitude:+22.123456;Longtitude
:+113.123456;speed:98;ACC:ON
1、Unit：“Minutes”
2、type：“0” cancel ；
7 Cut Engine AS1234ENGINE:OFF ENGINE:OFF;OK
8 Enable Engine AS1234ENGINE:ON ENGINE:ON;OK
9 Monitoring Number AS1234LISTEN:13481944860# Device will phone to telephone nuber13481944860
10 SET Speed Limit AS1234SPEED:120#
AS1234SPEED:0# ESPE:120;OK ESPE:OFF;OK 1、Unit：“km/h”
2、Type and range：“0”cancel speed limit
11 User DefinedAlarm 1 AS1234 DEFINED1:1#
AS1234 DEFINED1:0# User-defined1:ON;OK User-defined 1:OFF;OK
Value type：“0”forbid；“1”open
(The alarm information will only send to authorized
Number and center number when Device work in
SMS mode )
12 User DefinedAlarm 2 AS1234 DEFINED2:1#
AS1234 DEFINED2:0# User-defined2:ON;OK User-defined 2:OFF;OK
Value type：“0”forbid；“1”open
(The alarm information will only send to authorized
Number and center number when Device work in
SMS mode )
Note：In all the SMS commands , the delete method of all the settable parameters is to change the parameters to ‘0’，it will be recognized as invalid command if leave it blank