Lcdmod Kit I2004AB-M1 User manual

I2004AB-M1
Perspex mini-ITX case
(Designed for Intel
®
Core
TM
i3/5/7 Processor
with
USB interface Big 20x4 LCD module
(White characters with blue background
User Manual
Website: http://www.lcdmodkit.com
Rev: 1.01 Mar 2011

2
CHAPTER 1 INTRODUCTION............................................................................................................2
C HAPTER 2 H ARDWARE S ETUP ..............................................................................................................3
C HAPTER 3 D RIVER I NSTALLATION ..................................................................................................... 11
C HAPTER 4 F RONT P ANEL LCD S OFTWARE I NSTALLATION .................................................................15
C HAPTER 5 S PEED F AN S OFTWARE I NSTALLATION ...............................................................................16
Chapter 1 Introduction
1.1 Pac age Contents
1.2 Specifiaction
Case
Case Color No color crystal clear (Acrylic
Corner Stand 72mm height Silver White (Surface treated sandblasted aluminium
Foot Stand M5 Screw (4.5mm height
Dimensions 190 x 199 x 78mm
(WxLxH, box height only, not included the height of foot stand
HDD Bays [2x] 2.5" HDD (under the motherboard
Foam Factor mini itx
Internal Height Total 72mm
Accessories
Exhaust Fan 6cm 6010 Pulse width modulation control
Fan cable Two way fan out PWM cable

3
Front Panel LCD
Data Transfer USB 1.1 compliant
LCD Resolution 20 Characters x 4 Lines
LCD color White characters / blue background
Screen Size 123.5 x 43 mm
Work with Lcd Smartie, lcd4linux and LCDProc
Opearting System Linux, Windows 98, XP, 7 32 & 64 bits
USB connection Internal USB connector
Chapter 2 Hardware etup
2.1 Installing corner stands to the bottom crystal clear plate
2.2 Installing hard dis to the bottom crystal clear plate
2.2.1 Place red fiber liners on mounting holes of hard dis

4
2.2.2 Place bottom crystal clear plate on the top of hard dis and install screws
(If you only use one hard drive, please cover the exhausted holes of the another drive bay)
2.3 Installing nylon studs on the bottom crystal clear plate
2.4 Installing rear panel

5
2.5 Connecting SATA data and power cables
2.6 Installing Mainboard and power cable and Wifi connector (if you have)

6
2.7 Exhausted fan installation
2.8 Connecting ON/OFF switch cable to front panel

7
2.9 Main board side
2.10 Connecting internal USB cable of front panel LCD to USB connector of motherboard

8
(D- = USBP*- , D+ = USBP*+)
2.11 Connecting the 2-way PWM fan cable to CPU fan connector of motherboard

9
2.12 Connecting the 2-way PWM fan cable (4-cable one for detecting the CPU fan speed) to CPU
fan
2.13 Connecting the 2-way PWM fan cable (3-cable one for controlling speed only) to exhaust fan

10
2.14 Installing the side and front panel
2.15 Installing the top panel

11
Chapter 3 Driver Installation
3.1 Power up message
3.2 Error message may be shown on your screen
3.3 Copy the driver folder to any driver or des top of your computer
3.4 Go to “Control Panel”

12
3.5 Go to “System and Security”
3.6 Go to “Device Manager”

13
3.7 “LCD2USB” with “!”, right clic the mourse and “Update Driver Software”
3.8 Choose “Browse my computer for driver software”

14
3.9 Find out the driver folder you copied before
3.10 Install this driver anyway

15
3.11 Close it
Chapter 4 Front Panel LCD oftware Installation
4.1 Unzip the “lcd_smartie_v5.4” to any driver any folder you li e.
4.2 Run “LCDSmartie”
4.3 Set the display plugin to “LCD2USB.dll” in setup

16
4.4 Change the LCD size to “4x20” and tune the LCD contrast and brightness of bac light
Note: For more details about LCDSmartie, please go through the official site of LCDSmartie
http://lcdsmartie.sourceforge.net/
Chapter 5 peedFan oftware Installation
4.1 In your bios setting, choose “CPU Fan Speed Control” as [Smart]

17
4.2Install the “SpeedFan 4.42” to any driver any folder you li e.
4.2 Run “SpeedFan”
4.3 Choose “Automatic fan speed” and then clic into “Configure”
4.4 In “Speeds” page, chosse the CPU and system fan and set their minimum value, maximum

18
value and chose “Automatically variated”
4.5 In “Temperature” page, choose the relationship between temperature and fan speed and
desire/warning temperature of CPU and System
4.6 Copy the “SpeedFan” shortcut into the start up, then “SpeedFan ” will
automatically running at each starting
With using our 2-way PWM control fan cable, both CPU and system fan speed can be controller
by the computer bios/software. Your computer can be ept silent when general usage.
Note: For more details about SpeedFan, please go through the official site of SpeedFan
http://www.almico.com/speedfan.php