lescolton ICECOOL II User manual

1
USER MANUAL
LESCOLTON ICECOOL II DUAL SYSTEM, POWERED
BY ELOS ME.
390 Market St 200
San Francisco, CA, 94102
Questions? Get in touch with us by live chat or email us:
[email protected]

2
CONTENTS
Product Introduction………………………………………………………..…………………….03
Contraindications…………………………………………………………………...................03
Considerations…………………………………………………..……………………………….....03
Safety warning………..……………………………………………………………………….…….03
Safety operation regulations……………………………........................................03
Product structure………………………………………………………………………...…….....04
How to use it…………………………………………………………………………………….…….04
Permanent hair removal treatment………………………….…………..………….......05
Operation suggestions……………………………….……………………………………….....06
Treatment intervals………………………………………………………………..…………......06
Skin rejuvenation treatment……………………………………………..……….…….......07
Specifications…………………………………..……………………………………….…………….07
Table of simple troubleshooting…………………………………………..…………........08

3
INTRODUCTION
- The new Lescolton powered by Elos Me is a dual system with the
functions of hair removal and skin rejuvenation. It integrates the multi-
term application of optical e-light technology in the field of Beauty &
Health.
- Before use, please read the instructions carefully.
- Suitable for men and women.
- People with dark skin should start with the lowest level and then adjust
to the proper level based on the adaptability of your skin.
Contraindications
- People under 16 years old.
- Inflammation of the skin.
- Photosensitivity.
- Implanted medical electronic device which may lead to operation errors.
Considerations
- The product has not been tested on pregnant women.
- Do not use the product directly on tattoos since they may absorb a large
quantity of energy.
- Do not use around the eyes, neck, or nipples since the skin of these areas
is relatively vulnerable.
- If the skin continues to be inflamed or swollen after 24 hours,
discontinue use until symptoms disappear.
Safety warning
- Do not block the vents during use.
- Do not allow the water or any moisture into the device.
- Use the device in inflammable or explosive conditions is prohibited.

4
Safety operation regulations
- Do not aim the light at eyes.
- Do not look directly at the light.
- Before use, please make sure that you have removed all metallic objects
such as rings, bracelets and so on, to avoid malfunction of the device.
- Use the machine in a room with a temperature inferior to 25 degrees
Celsius.
Product Structure
HOW TO USE
Permanent hair removal treatment
- Before use, preferably wax all the hair around the treatment area. If you
can´t wax, you can shave the area.
- Insert the power cable into the machine and plug it in.
- Turn on the machine from the touch power of the LCD screen by
pressing it for 2 or 3 seconds until the device turns on.

5
- Using the same power button, you can select your desired power level.
Each press of the button increases the power level. You have the option
to choose from up to 10 power levels. If you don't feel any tingling or
discomfort at the lowest power levels, it's recommended to opt for the
highest power level available.
- It is possible to select four treatment modes using the green touch
button located at the bottom right of the LCD screen (mode change
button): hair removal, cooling hair removal, skin rejuvenation, and
cooling skin rejuvenation.
- Switching between the hair removal and skin rejuvenation modes: press
the “work mode switch button”; HR indicates the hair removal mode and
SR indicates the skin rejuvenation mode.
- Turning on/off the Ice-cool care mode: press the “work mode switch
button” (the button to the right of the touch screen) and hold it down
for 2/3 seconds. The snowflake indicates that the Ice-cool care mode is
on; otherwise, the Ice-cool care mode is off.
- Once the type of treatment and level of power is selected, gently rest
the lamp on the skin. When the green light on the side of the device
flashes, press the fire button on the device handle. For optimal results,
repeat shots on the same area 2 or 3 times. To proceed with the next

6
shot, it will be necessary to wait for the green light on the side of the
machine to flash again.
- To allow the machine to shoot automatically without pressing the
shutter button, you can enter the automatic use mode. To enter
automatic mode, press the shutter button for two or three seconds until
two beeps are emitted. This way, the machine will emit the shots
automatically when the lamp is resting on the skin. Keep the lamp
supported until 2 or 3 shots are emitted for best results.
- To return to manual shooting mode it will be necessary to press the
shutter button again for 2 to 3 seconds until two beeps are heard again.
- For more precision in facial treatment, use the magnetic precision
attachment to reduce the irradiation area.

7
Treatment intervals
Treat every 3 to 5 days during the first month, weekly during the second
month, every 15 days during the third month and every 30 days from the
fourth month until you permanently remove the hair.
Definitive hair removal is a process of several months. The results are not
seen immediately due to two reasons:
1- It is necessary to wait until all the body hair is in the active growth
stage so that it can be affected by the treatment. For this, it is necessary
to wait several months.
2- It is necessary to perform several treatments for hair that is in the
active growth stage to weaken the hair root until it is permanently
affected, and the hair does not grow back. The changes will be noticed
over the months.
People with blond, grey, or red hair will normally need twice as many
sessions as people with black and brown hair, so the treatment can be
extended to between 6 to 12 months.
Skin rejuvenation treatment
Press the green touch button with the freezing icon located on the bottom
right of the screen to choose the skin rejuvenation (SR) treatment. By
pressing and holding this same touch button for 3 seconds, you can
activate or deactivate the freezing mode. Activating the freezing mode will
make the treatment more comfortable.
Specifications
Size of the main unit: 190x148x96mm.
Size of the package (box): 260x180x111mm.
Power supply: input: 100-240V AC-50/60Hz.
Weight: 1,4 kg.
Irradiation area: 4 cm2.
Irradiation area with facial attachment: 2 cm2.
External environment: Temperature: - 20 - 50 degrees Celsius.
Warranty: 4-year warranty.

8
Table of simple troubleshooting
- No power: The power cord is not well connected.
- Can´t turn on the machine: Press the “on” button for 2 seconds.
- The level indicator is flashing after boot: The cartridge is not well
installed.
- Automatic shutdown: The machine shuts down automatically after 5
minutes if it is not used.