Line of Sight LOS3-CPUT-M-X-X User manual

1 of 2 Line of Sight | [phone] | los.workriteergo.com
Line of Sight Workcenter
4 mm Allen Wrench
CPU Width
CPU Height
or
or
or
CPU Width
CPU Height
or
or
or
CPU Width
CPU Height
or
or
or
CPU Width
CPU Height
or
or
or
CPU Width
CPU Height
or
or
or
CPU Width
CPU Height
or
or
or
4–7" Wide
7–9" Wide
9–12" Wide
12–14" Wide
AThin Client, Micro CPU Supports, Le & Right
Qty: 2 BThin Client, Micro CPU
Support Plate
Qty: 1 CThin Client, Micro CPU
Hangers, Le & Right
Qty: 2 D¼"-20 × ½" Low
Profile Bolt
Qty: 8 E¼"-20 Wing Nuts
Qty: 8
Line of Sight Hang-On CPU Holder Installation Instructions:
LOS3-CPUT-M-X-X
Parts Included
Required, Sold Separately
1 Assemble CPU Supports to Support Plate
1.1 Attach the CPU Support Plate (B) to the Le CPU
Support (A) with two Low Profile Socket Head
Screws (D) and two Wing Nuts (E). Keep assembly
loose so you can size to the CPU width in Step 1.3.
Note: The Support Plate width will dier, based
on the model you ordered for your CPU width.
1.2 Attach Support and Plate assembly to the Right
CPU Support. Keep assembly loose so you can size
to the CPU width.
1.3 Place CPU in the Holder and adjust the Supports
to fit the width of the CPU. Remove the CPU and
tighten the Screws securely with a 4mm Allen
Wrench.
Note: Confirm that all Low Profile Socket Head Screws (D) are facing inward and all Wing Nuts (E) are facing
outward so the Wing Nuts do not damage your CPU!
Note: CPU placement will depend on your over all
room configuration, Switch locations, Grommet Power
choices and in some instances, cable lengths. Consider
all wiring objectives prior to installing CPU Holders.
Single User Workstations can be configured with the
CPU on either the le or right side of the Chassis. Dual
User Workstations can be configured Le, Right, Inside
or Outside.
Single Le
Dual Le
Dual Outside
(preferred)
Single Right
Dual Right
Dual Inside
(avoid-may conflict with USB & switch)
Tools Needed
1.1
1.2
1.3
A
B
EE
A
D
D
Show with 7-9" wide Support Plate
LOS3-CPUT-M-A-X

2 of 2 Line of Sight | [phone] | los.workriteergo.com
#1500401 Rev A
CPU Width
CPU Height
or
or
or
CPU Width
CPU Height
or
or
or
4 Hang the CPU holder on Line of Sight Chassis
4.1 Place the CPU in the Holder and hang the CPU
Holder over the front of the chassis under the
Worksurface.
4.2 Route all cabling according to the LOS Chassis
instructions and equipment manufacturers
specifications.
4.3 Manage all cabling with P-Loops, Cable Clips,
Wire Ties and Wire Loom provided with your
Chassis.
3 Route Cables– Guidelines
Note: Cabling and mounting of the CPU is a diicult process and unique to each situation. Use these guidelines
as a reference, making sure to keep all cabling away from interfering with the Monitor Li.
3.1 Remove the Front and Rear Panel from your Line of
Sight Chassis for access to route the cables.
3.2 Route cables in the most convenient direction using
front Chassis Grommet access for larger CPU's and
over the top of the chassis for smaller CPU's.
3.3 Use the Wire Loom to route cables from the CPU to
the Keyboard Tray for keyboard and mouse.
3.4 Route all power to the shared power area which
may include installed Power Tracks or Power Bars.
3.5 Use the bottom Trough to bundle any excess
cabling.
3.6 Use the Desktop Grommets to route power and
data to the desktop as needed.
2 Attach CPU Hangers to Base Assembly
2.1 Place CPU in the Holder and adjust the CPU Hangers (C)
to fit the height of the CPU.
2.2 Attach the Le and Right CPU Hangers (C) to the
Support assembly with four Low Profile Socket Head
Screws (D) and four Wing Nuts (E) and tighten the
screws securely with the 4mm Allen Wrench.
Top of Chassis
Cabling over
top of Chassis
Cabling through front
Chassis Grommet
Desktop
Grommet
Keyboard &
Mouse
Wire
Loom
Power &
Data Out
Chassis
Grommet
Shared Power
Bottom Trough
Monitor Out &
Monitor Power
CPU
CPU Power
2.1 2.2
E
C
C
D
3.2
4.1
3.2
3.3
3.4
3.5
3.6