Masco Bristan BL BSM C User manual

SAFETY
NOTE !
AFTERCARE INSTRUCTIONS
Your fitting has been manufactured to a high quality finish therefore
should be treated with care to preserve its visible appearance. All
surface finishes will wear if not cleaned correctly, the recommended
and safest way to clean your fitting is to wipe with a soft damp cloth.
Stains can be removed using washing up liquid. All domestic
cleaning products, including non-scratch cleaners, can damage the
surface and appearance of your fitting.
GUARANTEE
All products are manufactured to the highest standards and a 5 year
guarantee covers any defect in manufacture. As gold and special
effect finishes are softer than chromium plate, special care must be
taken when cleaning; a 3 year guarantee covers these finishes.
NOTE: The 5 year guarantee on the valves is invalidated if damaged
by any waterborne debris.
In the interests of continuous product development we reserve the
right to alter specification as necessary.
PRODUCT CODE: BL BSM C
TELEPHONE HELPLINE: 0844 701 6273
Bristan Group Ltd
Birch Coppice Business Park
Dordon
Tamworth
Staffordshire
B78 1SG
UK
A Masco Company
Web Site: www.bristan.com
Telephone: [phone]
Facsimile: 0844 701 6275
Email: [email protected]
(FI BL BSM)
(R
3
)
(
U
)
Blade Deck Mounted
Bath Shower Mixer
Prior to drilling into walls, check there are no
hidden electrical wires, cables or water supply
pipes with the aid of an electronic detector. If you
use power tools do not forget:
•Wear eye protection
•Unplug equipment after use
Fitting Instructions
& Contents List
Please keep these instructions for future reference and request
ofreplacementparts.
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

ab
c
d
e
f
2
3
1
4
56
7
8
9
SAFETY
NOTE !
WATER PRESSURE
This mixer is suitable for use at all supply pressures. However for
optimum use both the hot and cold supplies should be reasonably
balanced. If the fitting is installed at low pressure (tank fed), then the
minimum height from the highest installed position of the showerhead
to the underside of the cold tank should be 1.0 metre to ensure
adequate shower performance.
This mixer should be installed in compliance with Water Regulations.
Where the supplies are unbalanced, i.e. hot water from cylinder
tank/cold from the mains, approved check valves must be fitted in the
supply pipes. For further details contact your Local WaterAuthority.
INSTALLATION DIAGRAM
Please Note:In the unlikely event you find a part missing please
contact our Customer Service Help line on 0844 701 6273 for
immediate dispatch of part.
CONTENTS
1. Mixer Body (x1) 6. Handset Holder (x1)
2. Rubber Washer (x2) 7. Fixing Screw (x1)
3. Backnut (x2) 8. Wall Bracket (x1)
4. Hose (x1) 9. Handset (x1)
5. Small Washer (x2)
INSTALLATION
1. Identify all components and check for completeness, particularly
before arranging fitting.
2. Fit the mixer body (1) to the bath and secure using the rubber
washers (2) and backnuts (3) below the bath. Connect the hot
and cold water supplies.
3. Fit the hose (4) to the mixer (1) and the handset (9) using the
small sealing washers (5). To adjust hose outlet position; loosen
screw (f) then rotate hose outlet to desired position. Secure in
placewith grubscrew (f).
Prior to drilling into walls, check there are no
hidden electrical wires, cables or water supply
pipes with the aid of an electronic detector. If you
use power tools do not forget to:
•Wear eye protection
•Unplug equipment after use
4. Fixwall bracket (8) to wall using the screw (7) andwall plug
provided, ensuring that the handset will reach it. Attach bracket
handset holder(6).
5. Fully open both valves letting them run for a few minutes, check
all joints and connections for leaks.
6. Operate the mixer in both bath and shower mode. To switch
from bath to shower mode, pull the diverter knob (e) up. After
use the mixer automatically reverts to thebath-filling mode.
MAINTENANCE
If the fitting begins to drip:
1. Turnoff thewater supply.
2. Prise out cap (a), loosen grub screw (b) and lift off handle (c).
3. Remove valve (d). Clean seating, seal andceramic disc.
4. Replace valve and head and turn on the water supply.
5. Contact our helpline if problem persists.
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk