Maxell MP-WU9101B User manual

1
DLP
®Projector
MP-WU9101B
User's Manual (detailed)
Operating Guide – Technical
Supported Signal Input Modes
Signal
Format Resolution
H
Freq.
KHz
Frame
Rate
Hz
PCLK
MHz
5
B
N
C
VGA
RGB
HV
5
BNC
RGB
HV
DVI
-D
HDMI / HDBaseT HD/
SDI/
3G
Remark
RGB
YUV(bit)
810 12
PC
640*480 31.469 59.94 25.175 √ √ √ √ VESA DMT
640*480 37. 5 0 0 74.99 31.500 √ √ √ √ VESA DMT
640*480 43.269 85 36.000 √ √ √ √ VESA DMT
800*600 37.879 60.32 40.000 √ √ √ √ VESA DMT
800*600 46.875 75 49.500 √ √ √ √ VESA DMT
800*600 53.674 85.06 56.250 √ √ √ √ VESA DMT
848*480 23.674 47.95 25.000 √ √ √ √ VESA CVT
848*480 31.020 60 33.750 √ √ √ √ VESA DMT
1024*768 48.363 60 65.000 √ √ √ √ VESA DMT
1024*768 60.023 75 78.750 √ √ √ √ VESA DMT
1024*768 68.677 85 94.500 √ √ √ √ VESA DMT
1280*720 35.531 47.95 57.987 √ √ √ √ VESA GTF
1280*1024 63.981 60.02 108.000 √ √ √ √ VESA DMT
1280*1024 91.146 85.02 1 57. 5 0 0 √ √ √ √ VESA DMT
1600*1200 75.000 60 162.000 √ √ √ √ VESA DMT
1920*1080 53.225 47.9 5 135.403 √ √ √ √ VESA CVT
1920*1200
RB 74.038 60 154.000 √ √ √ √ VESA CVT
1366*768 47.712 60 85.500 √ √ √ √ VESA DMT
1440*900 55.935 60 106.500 √ √ √ √ VESA DMT
1280*768 47.7 76 60 79.500 √ √ √ √ VESA DMT
1280*800 49.702 60 83.500 √ √ √ √ VESA DMT
1280*960 60.000 60 108.000 √ √ √ √ VESA DMT
Apple
MAC
640*480 35.000 66.67 30.240 √ √ √ √ Apple MAC
832*624 49.720 74.54 5 7. 2 8 0 √ √ √ √ Apple MAC
SDTV
480i 15.734 59.94 13.500 √ √
1440*480i 31.468 60 27.000 √ √ √ √
1440*576i 31.250 50 27.000 √ √ √ √
576i 15.625 50 13.500 √ √
EDTV 480p 31.469 59.94 27.000 √ √ √ √ √ √ √ √
576p 31.250 50 27.000 √ √ √ √ √ √ √ √
(continued on next page)

2
Supported signals
Supported Signal Input Modes
Signal
Format Resolution
H
Freq.
KHz
Frame
Rate
Hz
PCLK
MHz
5
B
N
C
VGA
RGB
HV
5
BNC
RGB
HV
DVI
-D
HDMI / HDBaseT HD/
SDI/
3G
Remark
RGB
YUV(bit)
810 12
HDTV
1080i 2 8.125 50 74.250 √ √ √ √ √ √ √ √ √
1080i 33.716 59.94 74.176 √ √ √ √ √ √ √ √ √
1080i 33.750 60 74.250 √ √ √ √ √ √ √ √ √
720p 3 7. 50 0 50 74.250 √ √ √ √ √ √ √ √ √
720p 44.955 59.94 74.176 √ √ √ √ √ √ √ √ √
720p 45.000 60 74.250 √ √ √ √ √ √ √ √ √
1080p 26.973 23.98 74.176 √ √ √ √ √ √ √ √ √
1080p 27.000 24 74.250 √ √ √ √ √ √ √ √ √
1080p 28 .125 25 74.250 √ √ √ √ √ √ √ √ √
1080p 33.716 29.97 74.176 √ √ √ √ √ √ √ √ √
1080p 33.750 30 74.250 √ √ √ √ √ √ √ √ √
1080p 56.250 50 148.500 √ √ √ √ √ √ √ √ √
1080p 67.4 3 3 59.94 148.352 √ √ √ √ √ √ √ √ √
1080p 6 7. 50 0 60 148.500 √ √ √ √ √ √ √ √ √
PsF
formats
1080sf 33.750 30 74.250 √
1080sf 28.125 25 74.250 √
(continued on next page)

3
Supported signals
SDI formats
Timing SDI Link mode Signal Standards Color
Encode
Sampling
Structure
Bit Depth
NTSC SD SMPTE 259M-C 270Mbps SD YCbCr 4:2:2 10
PAL SD SMPTE 259M-C 270Mbps SD YCbCr 4:2:2 10
1080i59 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
1080i60 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
1080P30 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
1080P25 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
1080i50 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
1080P24 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
720P60 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
720P50 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
1080Sf25 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
1080Sf30 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2:2 10
1080P50 3G Level A SMPTE 424M 3Gbps YCbCr 4:2:2 10
1080P59 3G Level A SMPTE 424M 3Gbps YCbCr 4:2:2 10
1080P60 3G Level A SMPTE 424M 3Gbps YCbCr 4:2:2 10
1080P50 3G Level B SMPTE 424M 3Gbps YCbCr 4:2:2 10
1080P59 3G Level B SMPTE 424M 3Gbps YCbCr 4:2:2 10
1080P60 3G Level B SMPTE 424M 3Gbps YCbCr 4:2:2 10
Test Cable: Belden 1694A
(continued on next page)

4
Supported signals
3D Timing Format
Standard Resolution V-Freq
(Hz) V-Total
H-Freq
(kHz)
HDBaseT
(*1)
HDMI1/2
(*1)
DVI-D
(*2) Remarks
720p50 Frame Packing 1280x720 50 1470 37. 5 √ √ *3
720p59 Frame Packing 1280x720 59.94 1470 44.96 √ √ *3
720p60 Frame Packing 1280x720 60 1470 45 √ √ *3
720p50 Top-and-Bottom 1280x720 50 750 37. 5 √ √ √ *3
720p59 Top-and-Bottom 1280x720 59.94 750 44.96 √ √ √ *3
720p60 Top-and-Bottom 1280x720 60 750 45 √ √ √ *3
1080p23 Frame Packing 1920x1080 23.98 2205 26.97 √ √
1080p24 Frame Packing 1920x1080 24 2205 27 √ √
1080i50 Side-by-Side (Half) 1920x1080 50 1125 56.25 √ √ √ *3
1080i59 Side-by-Side (Half) 1920x1080 59.94 1125 67.43 √ √ √ *3
1080i60 Side-by-Side (Half) 1920x1080 60 1125 67. 5 √ √ √ *3
1080p50 Side-by-Side (Half) 1920x1080 50 1125 56.25 √ √ √ *3
1080p59 Side-by-Side (Half) 1920x1080 59.94 1125 67.4 3 √ √ √ *3
1080p60 Side-by-Side (Half) 1920x1080 60 1125 6 7.5 √ √ √ *3
1080p50 Top-and-Bottom 1920x1080 50 1125 56.25 √ √ √ *3
1080p59 Top-and-Bottom 1920x1080 59.94 1125 67. 4 3 √ √ √ *3
1080p60 Top-and-Bottom 1920x1080 60 1125 67. 5 √ √ √ *3
1080p50 Frame Sequential 1920x1080 50 1125 56.25 √ √ √ *3
1080p59 Frame Sequential 1920x1080 59.94 1125 67. 4 3 √ √ √ *3
1080p60 Frame Sequential 1920x1080 60 1125 67. 5 √ √ √ *3
*1: Based on IT6802 chip specication
*2: Based on IT6535 chip specication
*3: Frame drop at scaler and frame doubling at formatter

5
ACOMPUTER IN
D-sub 15pin mini shrink jack
<Computer signal>
• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)
• H/V. sync. signal: TTL level (positive/negative)
• Composite sync. signal: TTL level
<Component video signal>
• Video signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated
Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated
Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated
• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60
Pin Signal Pin Signal
1 Video Red, Cr/Pr 9 (No connection)
2Video Green, Y 10 Ground
3 Video Blue, Cb/Pb 11 (No connection)
4 (No connection) 12 SDA (DDC data)
5 Ground 13 H. sync / Composite sync.
6 Ground Red, Ground Cr/Pr 14 V. sync.
7 Ground Green, Ground Y 15 SCL (DDC clock)
8 Ground Blue, Ground Cb/Pb
Connection to the ports
① ⑤④③②
⑥ ⑩⑨⑧⑦
⑪ ⑮⑭⑬⑫
①⑤④③②
⑥⑩ ⑨ ⑧ ⑦
⑪⑮⑭⑬⑫
Connection to the ports
12V OUTPUT
(OPTION) A

6
COMPUTER IN2 BR/Cr/Pr, CG/Y, DB/Cb/Pb, EH, FV
BNC jack x5
<Computer signal>
• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)
• H/V. sync. signal: TTL level (positive/negative)
• Composite sync. signal: TTL level
<Component video signal>
• Video signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated
Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated
Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated
• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60
12V OUTPUT
(OPTION) BCDEF
G
CONTROL
D-sub 9pin plug
* About the details of RS-232C communication,
please refer to the next section.
Pin Signal Pin Signal Pin Signal
1 (No connection) 4 (No connection) 7 RTS
2 RD 5 Ground 8 CTS
3 TD 6 (No connection) 9 (No connection)
H12V OUTPUT(OPTION)
Power terminal only for an optional lens. Use this port when you need power supply for the
optional lens. Do not connect other device to this port. Put the cover when it is not used.
Refer to the manual of the optional lens for details.
① ②
⑥⑦⑧⑨
⑤④③
①②
⑥⑦⑧⑨
⑤④③
G
H
Connection to the ports (continued)

7
Connection to the ports (continued)
IHDMI 1, JHDMI 2
• Type :Digital audio/video connector
• Audio signal: Linear PCM (Sampling rate; 32/44.1/48 kHz)
Pin Signal Pin Signal Pin Signal
1T.M.D.S. Data2 +
N.C. 8T.M.D.S. Data0 Shield
MHL_Shield 15 SCL
CD_PULLUP
2T.M.D.S. Data2 Shield
CD_SENSE 9T.M.D.S. Data0 -
MHL- 16 SDA
N.C.
3T.M.D.S. Data2 -
N.C. 10 T.M.D.S. Clock +
N.C. 17 DDC/CEC Ground
VBUS_CBUS_GND
4T.M.D.S. Data1 +
N.C. 11 T.M.D.S. Clock Shield
TMDS_GND
18
+5V Power
VBUS
5T.M.D.S. Data1 Shield
TMDS_GND 12 T.M.D.S. Clock -
N.C. 19 Hot Plug Detect
CBUS
6T.M.D.S. Data1 -
N.C. 13 CEC
N.C.
7T.M.D.S. Data0 +
MHL+ 14 Reserved (N.C. on device)
N.C.
① ⑤
④
③
②⑥⑩
⑨
⑧
⑦⑪⑮
⑭
⑬
⑫
⑲
⑱
⑰
⑯
①⑤
④
③
②⑥⑩
⑨
⑧
⑦⑪⑮
⑭
⑬
⑫
⑲
⑱
⑰
⑯
K
HDBaseT
RJ-45 jack
Pin Signal Pin Signal Pin Signal
1 HDBaseT0+ 4 HDBaseT2+ 7 HDBaseT3+
2 HDBaseT0- 5 HDBaseT2- 8 HDBaseT3-
3 HDBaseT1+ 6 HDBaseT1-
① ⑤
④
③
② ⑥ ⑧
⑦
①⑤
④
③
②⑥⑧
⑦
12V OUTPUT
(OPTION)
J
I
K

8
12V OUTPUT
(OPTION)
LM
N
O
Connection to the ports (continued)
DVI-D
DVI-D jack (digital to digital)
Pin Signal Pin Signal Pin Signal
1 T.M.D.S. Data2 - 9 T.M.D.S. Data1 - 17 T.M.D.S. Data0 -
2 T.M.D.S. Data2 + 10 T.M.D.S. Data1 +
18 T.M.D.S. Data0 +
3 T.M.D.S. Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield
4 - 12 -
20 -
5 - 13 - 21 -
6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield
7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock +
8 - 16 Hot Plug Detect 24 T.M.D.S. Clock -
1 2 3 4 5 67 8
910 11 12 13 14 15 16
17 18 19 20 21 22 23 24
N
SDI MIN, LOUT
BNC jack
• SD/HD/3G-SDI signal, Digital, 0.8V±10%, 75Ω terminated
• System:
SD-SDI signal: conforming to SMPTE ST 259-C standard
YCBCR 4:2:2 10-bit
480i, 576i
Single link HD-SDI signal: conforming to SMPTE ST 292 standard
YPBPR 4:2:2 10-bit
720p@50/60, 1080i@50/60, 1080sf@25/30
3G-SDI Level-A signal: conforming to SMPTE ST 424 standard
YPBPR 4:2:2 10-bit
1080p@50/60
OREMOTE CONTROL
Ø3.5 stereo mini jack

9
RS-232C Communication
RS-232C Communication
When the projector connects to the computer by RS-232C communication, the
projector can be controlled with RS-232C commands from the computer.
For details of RS-232C commands, refer to RS-232C Communication command
table (&14).
Connection
1. Turn off the projector and the computer.
2. Connect the projector's CONTROL port and the computer's RS-232C port
with a RS-232C cable (straight). Use the cable that fullls the specication
shown in gure.
3. Turn the computer on, and after the computer has started up turn the projector
on.
CD (1) (1) －
RD(2) (2) TD
TD (3) (3) RD
DTR (4) (4) －
GND (5) (5) GND
DSR (6) (6) －
RTS (7) (7) CTS
CTS (8) (8) RTS
RI (9) (9) －
12345
9
8
7
6
CONTROL port of
the projector
RS-232C port of
the computer
RS-232C cable
(straight)
RS-232 CONTROL
① ②
⑥⑦⑧⑨
⑤④③
NOTE • In case of replacement and RS-232 cable (cross) has been installed, please
add a packed RS-232 cable (cross) to make connection correctly.

10
RS-232C Communication (continued)
Communication settings
1. Protocol
19200bps, 8N1
2. Command format ("h" shows hexadecimal)
Byte Number 0 1 2 3 4 5 6 7 8 9 10 11 12
Command
Action
Header Data
Header
code
Packet
Data
size
CRC
ag Action Type Setting code
L H L H L H L H L H L H
<SET> Change setting to
desired value [(cL)(cH)]
by [(bL)(bH)].
BEh EFh 03h 06h 00h
(aL) (aH) 01h 00h (bL) (bH) (cL) (cH)
<GET> Read projector
internal setup value [(bL)
(bH)] .
(aL) (aH) 02h 00h (bL) (bH) 00h 00h
<INCREMENT>
Increment setup value
[(bL)(bH)] by 1.
(aL) (aH) 04h 00h (bL) (bH) 00h 00h
<DECREMENT>
Decrement setup value
[(bL)(bH)] by 1.
(aL) (aH) 05h 00h (bL) (bH) 00h 00h
<EXECUTE> Run a
command [(bL)(bH)].
(aL) (aH) 06h 00h (bL) (bH) 00h 00h
[Header code] [Packet] [Data size]
Set [BEh, EFh, 03h, 06h, 00h] to byte number 0 to 4.
[CRC ag]
For byte number 5, 6, refer to RS-232C Communication Command table
(&14).
[Action]
Set functional code to byte number 7, 8.
<SET> = [01h, 00h], <GET> = [02h, 00h], <INCREMENT> = [04h, 00h]
<DECREMENT> = [05h, 00h], <EXECUTE> = [06h, 00h]
Refer to the RS-232C Communication command table(&14).
[Type] [Setting code]
For byte number 9 to 12, refer to RS-232C Communication command table
(&14).