MDI Pocket Projector User manual

User Manual

If the actual setting and using method of this manual is not consistent with the product, please call our customer service support.
The manufacturer accepts no liability if these instruction are not followed.All contents in this user manual are subject to change without notice.
Read the entire user manual carefully.Follow all safety instructions in order to ensure proper operation of your device.
With the installation guide on the following pages,you can start using your device quickly and easily.
Thank you for purchasing our Pocket Projector.We hope you enjoy your device and its many functions!
Safety Precaution
Transportation Precautions
Kindly Remind
Please follow the below safety precautions, this will maintain the lifetime of the device.
◆ Do not place the device on soft surfaces such as tablecloths or carpets and do not cover the ventilation slits.
Otherwise the device could overheat or catch fire.
◆ Environmental working condition: Projector can be used at 5℃- 40℃.
◆ Use only the enclosed power adapter. Check whether the electrical voltage of the power supply matches the
electrical voltage available at the setup location.
Danger of Damage to the Eye by High Power LED
This device is equipped with a high po wer LED (Light Emitting Diode), which emits very bright light. Do not
stare directly into the projector lens to avoid eyes injury or irritations.
◆ Disconnect all peripheral devices of the projector before transport.
◆ Confirm the projector is switched off before transport.
◆ Ensure a good protection and packaging before the transportation of the projector. Do not rub or scrape the
surface during the transport.
◆ The following Pocket Projector pictures and function descriptions are for reference only and subject to the
material object. All contents in this user manual are subject to change without notice. Our com pany reserves
the right of the final interpretation.
◆ Do not connect any defect cables, accessories or other defect peripheral devices.
◆ Switch off the device and disconnect it from the power supply before cleaning the surface. Use a soft, lint-free cloth. Never use liquids,
gaseous or easily flammable cleansers (sprays, abrasives, polishes, alcohol).
◆ Do not allow any moisture to reach the interior of the device.
◆ Switch off the device and disconnect it immediately from the power supply if liquids or foreign substances end up inside the device.
◆ Always handle the product with care.
◆ Do not place the projector on your legs or any other body parts, to prevent any discomfort or injuries, caused by the heat from the device.
◆ Avoid touching the lens.
◆ Never place heavy or sharp objects on the device or the power cable.
◆ Protect the device against direct sunlight, heat, large temperature fluctuations and moisture. Do not place the device in the vicinity of
heaters or air conditioners.
◆ Do not use the device during lightning thunderstorm.
◆ Do not make any repairs to the device by yourself. Improper maintenance can result in injuries or damage to the device. Have your device
repaired only by an authorized service centre.
◆ Do not remove the type label from your device; this would void the warranty.
01 Overview 02
1
2
3
Overview

Pocket Projector Description
4 5 Accessories Description
Please unpack and check all of the following items carefully. If anything is missing,
please contact your dealer.
HDMI cable Adapter
Remote Control
Tripod
User Manual
Projector
Warranty Card
User Manual
Micro USB cable
Display
Technology
DLP Video Format RM,RMVB,AVI,MKV,WMV,VOB,MP4
Light
Source
LED Music Format MP3, WMA,AAC
LED life >200000hours Picture Format JPEG,BMP,PNG
Port HDMI/MHL/AV/VGA/USB/
USB/Micro SD card(TF)
Resolution 854*480
Built-
Built-
in Speaker 1*1W
Projection
Size
36”-112”
(1M-3M)
Power
Consumption
12W
Aspect Ratio 1.19:1
in Battery 2500mAhContrast
ratio(FIFO)
<3000:1
Operating
Voltage
DC 5V /2.5A
THD <1.0%
D
(L×W×H)
imension 110mm*95mm*16mmUniformity >85%
Weight 178g

03 Features and Function Description
C
E
F
G
A
B
D
A: ↑Navigate upward in the menu operation or
can be used to higher the volume during play mode
B: ← Navigate left
C: Back button: takes you one step back in the menu or to
cancel a function.
D: ◎ Power button: press the button for 3-5 seconds to switch off
or press 1 second to switch of the device.
E: ↓Navigate downward in the menu operation or
can be used to lower volume during play mode
F: → Navigate right
G: Enter Key
H: Sensor Spot
Note: Please touch the sensor spots in order that the projector accurately senses your instructions.
H
I: LED Lens Front view
Back view
K: Audio Out L: HDMI
M: USB O: DC-In ( the power input Port)
N: Remote Control receiver
J: Air Outlet

Left view
Right view
P: Selection key
(selection between projector
and power bank mode)
Q: Air Inlet
Remote Control Key Description
S:TF card (Micro SD card)
R: Manual focus wheel (adjust screen sharpness)
Note: 1. To use the remote control, you need to point it to the remote control receiver at the back side of the projector.
2. It is necessary to connect your projector to the power supply if you want to turn on the projector by the remote control.
Power button/Switch on/off
Main Menu/Fast return to main menu
Mute/Mute the volume
Back/Exit
UP/Navigate upward in the menu operation or can
be used to higher the volume during play mode
Pause/Pause the music or video
Left/Left control key
OK/Set up multiple video playing list In video mode
Right/Right control key
HDMI/AV/VGASignal switching key
Down/Navigate downward in the menu operation or
can be used to lower the volume during play mode
Setting/System set up
Picture/Select files for the slideshow
Music/Select files for music playback
Video/Select files for video playback
Volume+/Volume higher
Backward/During Video playback start backward
Previous/During music playback select previous music
Volume-/Volume lower
Forward/During Video playback start forward
Next /During music playback select next music

Charging Description Interface Functions Description
Power Button
Any device with discharge function can charge the projector. In switched off condition,
charging the projector takes about 150 minutes.
The power button lights red during charging.
When the battery is full，the power button lights in red and blue color.
The Projector’s working time is about 110 min with a fully charged battery.
The working time is about 80 min with EZCast function.
Please switch the selection key to charging mode and then connect the projector to the device.
If you need the projector to project at the same time, please press the power button on.
This projector can be used as a power bank to charge other digital devices via the USB cable.
HDMI/MHL port on the back side
The Apple special HDMI cable is required to connect any Iphone/Ipad.
HDMI cable (not included)
HDMI/MHL port on the back side Android mobile phone: MHL cable is required to connect.
Any digital device which supports MHL,
can synchronize with the projector by connecting it through the corresponding required cable.
USB Port
MHL
Any digital device which supports HDMI,
can synchronize with the projector by connecting it through the corresponding required cable.

HDMI/MHL port on the back side
HDMI/MHL port on the back side Computer
VGA(not included)
HDMI/MHL cable(not included)
Yellow
Red
White
AV (not included)
Any digital device which supports AV/MHL,
can synchronize with the projector by connecting it through the corresponding required cable.
Any digital device which supports VGA,
can synchronize with the projector by connecting it through the corresponding required cable.
BD/HDMI output port
HDMI port
HDMI port VGA port
HDMI port
Headphone jack instruction
Headset
Headphone
Speakers
HDMI/MHL port on the back side Headphone jack at the back side

TF( ） TF( ）
TF( ）
USB instruction
TF(Micro SD card) instruction
USB port at the back side
USB stick (not included)
TF(Micro SD card) port at the side TF(Micro SD card) (not included)
Max. 32GB
*Other digital device can be charged through the USB port.
The projector support projection of video/music/picture/text which are stored on an USB stick.
1. Switch on the projector
Press the on/off button on the top for 3-5 seconds. The main menu appears after the initial screen. Use the focus wheel on the
side to adjust the image sharpness.
Note: Do not cover the projector when it’s working. Otherwise the device could overheat.
The projector support projection video/music/picture/ text which are stored on a TF(Micro SD card).
Max. 32GB
Media Playback
Initial screen

TF卡
TF卡
Connect TF card
9
1. Choose one mode (Video/Picture /Music) on the main menu
Main menu
① Insert TF card to the TF card slot, then the following interface will appear: ② Insert USB stick to the USB port, then the following interface will appear:
③ Chose TF or USB as your need, click the Enter key,
the following interface will appear:
The following pictures are the interface sample in Video /Picture / Music

The following pictures are the interface sample in Video /Picture / Music / EZCast mode
Interface Introduction
For Pocket Projector, signal Source: HDM/MHL/VGA/AV
10
① Video mode ② Picture mode Notes:
Insert the memory card into the slot until it snaps into position.
Press lightly on the memory card to remove it.
Danger:
Prematurely Remove a Memory Card or USB disk
Never pull out the memory card or USB while the device is accessing it. This could cause data to be damaged or lost.
③ Music mode ④EZCast mode
11
NO. Mode Function
1 HDMI High definition digital input
2
MHL
Digital multimedia input interface
3 VGA Digital multimedia input interface
4 AV Digital multimedia input interface
music

Trouble Shooting12
If a problem occurs that cannot be corrected with the instructions in this user manual (see also the help below),
follow the steps given here.
Power Cycling
1.Switch the device off using the on/off switch on the top.
2.Wait at least ten seconds.
3.Switch the device on using the on/off switch on the top.
4.If the problem repeats, please contact our technical customer service or your retailer.
Warm Reminder:
Pocket Projector has a built-in fan for heat dissipation to reduce the temperature of the device.
It is normal if there is a slight sound when the fan starts or works.
Problems Solutions
• Check if the cables are connected to the right connectors
• Connect your computer or a compatible power supply to
recharge the internal battery. Make sure the Pocket
Projector is turned off
• Check the cables to the external device
• Set the volume on the external device
• Only the original cables from the device manufacturer
may function
The Pocket Projector can
not be turned on
The Pocket Projector
can not connect with
an external device
No sound from the
external connected device