Members Mark BQ06042-1 User manual

1
Grill Guide
For Model BQ06042-1
Professional Liquid Propane Gas Island Grill
FOR YOUR SAFETY:
1. Read this Grill Guide before attempting to
assemble or operate your grill.
2. Follow all safety instructions.
3. Check for leaks according to directions in this
Grill Guide before operating your grill, even if
purchasing an assembled grill.
4. Keep this Grill Guide for future reference.
5. Contact 1-800-933-0527 should you need
assembly assistance or have any questions.
Stop!
Missing a part? No need to go back to SAM'S CLUB!
SAM'S CLUB does not stock parts for this item at the Club, but our grill team is here to
help you. If you need parts, whether they are missing or damaged,
please call Toll Free Help Line 1-800-933-0527
Call us between 8:30 AM to 5:00 PM Central Time
,
Monda
y
throu
g
h Frida
y
.

2
Safety Precautions
Always read and follow all DANGER, WARNING, AND FOR YOUR SAFETY notices in this Grill
Guide. Failure to do may result in serious bodily injury or death, or in a fire or an explosion causing
damage to property.
1. Grill installation must conform with local codes, or in their absence, with either the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or
Propane Storage and Handling Code, B149.2.
2. This gas grill, when installed, must be electrically grounded in accordance with local codes, or, in
the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian
Electrical Code, CSA C22.1.
3. This gas grill shall be used outdoors only, and shall not be used in a building, garage, or any other
enclosed area.
4. This gas grill is not intended to be installed in or on recreational vehicles and/or boats.
5. Never use any other type of fuel for this grill other than that specified on the name plate attached to
the grill or the cover of this Grill Guide.
6. Only use the pressure regulator with a type 1 connector that is supplied with this gas grill.
7. Before each use, check the gas hose for excessive abrasion or wear, or cuts. Replace a hose
assembly showing those signs with the hose assembly specified in the parts list before using the
grill.
THIS GRILL IS FOR OUTDOOR USE ONLY.
If stored indoors, then detach and leave propane cylinder outside.
WARNING
1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
!
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from the appliance, and immediately call your gas supplier or your fire
department.
!
WARNING
Combustion by-products produced when using this product contain chemicals known to the State of California
to cause cancer, birth defects, and other reproductive harm.
!
TO THE INSTALLER OR PERSON ASSEMBLYING THIS GRILL:
Leave this Grill Guide with the consumer.
TO THE CONSUMER:
Retain this Grill Guide for future reference.

3
Table of Contents
Safety Precautions……….……………………………..……………...…………...…… 2
Table of Contents…………………….…………………………………..……….……...3
Warranty……………………………….………………………………………….…….. 4
Customer Support Center……………….………………………………………….…….4
Assembly Instructions...…………………………………………………………..…..5-13
General Information and Operation………………..………………………………..14-24
Trouble Shooting Guide……………………………………………….................……..25
Frequently Asked Questions……………………………………………………………26
Write down here and keep for future
reference
Date of Purchase: _________________
Serial Number: ___________________
The serial number may be found on the placard located
on the back of the grill
BQ06042-1
Retailer :
Address :
Visit us at: www.samsclub.com

4
Limited Warranty
The manufacturer warrants to the original
consumer-purchaser that this product shall be
free from defects in workmanship and materials
under normal and reasonable use when
assembled and operated according to this Grill
Guide from date of purchase as follows:
One year except as noted below:
Stainless Steel Burners – 3 years
Stainless Steel Parts except Burners, Grates,
Warming Rack, and Heat Diffusers - 5 years
The manufacturer will, at its option, refinish or
replace any product or part found to be defective
during the limited warranty period. There may be
a shipping charge. The manufacturer may require
you to return the part(s) claimed to be defective
for its inspection, freight or postage prepaid.
Contact our Customer Support Center as shown
below before returning any part(s).
Additional information can be obtained by
writing:
Barbecue Grills
Warranty Dept.
1375 Mitchell Blvd
Schaumburg, IL 60193
The manufacturer will require reasonable proof
of purchase. We strongly recommend you
keep your sales receipt and register your grill.
You can attach your receipt to this guide.
This limited warranty does not cover the cost of
any inconvenience or property damage due to
failure of the product and does not cover damage
due to misuse, abuse, alteration, improper or
failure to perform normal and routine
maintenance, discoloration, scratches, rust,
accident, damage arising out of transportation of
the product, or normal wear and tear. This
limited warranty will not apply to any grill used
for commercial use.
This limited warranty is the sole warranty given
by the manufacturer and is in lieu of all other
warranties; express or implied, including implied
warranty of merchantability or fitness for a
particular purpose. Neither manufacturer dealers
nor the retail establishment selling this product
have any authority to make any warranties or to
promise remedies in addition to or inconsistent
with those stated above.
This limited warranty applies only to products
sold at retail, and is not transferable.
The manufacturer's maximum liability, in any
event, shall not exceed the purchase price of the
product paid by the original consumer-purchaser.
Some states do not allow the exclusion or
limitation of incidental or consequential damages.
Therefore, the above limitations or exclusions
may not apply to you. This warranty gives you
specific legal rights and may also have other
rights, which vary from state to state.
Customer Support Center
Thanks for purchasing a Member’s Mark Grill. We’re here to help you maximize your enjoyment and
appreciation of your new grill. Please don’t hesitate to contact us should you have any questions regarding
assembly, performance, warranty, or accessories. We have a full line of replacement parts available. Please
have your model number ready before you contact us. We’re here to serve You!
• If you need assistance or to order parts: Call 1-800-933-0527 or send a FAX to 1-847-252-1001.
• Business hours: Monday through Friday; 8:30AM-5:00PM Central Time.
• Visit us on the web at: www.omahagrills.com

5
Assembly Instructions
This page will give you an overview of information to assemble your grill. The following pages will show in
step-by-step detail how to do so. We offer the following suggestions to make your grill assembly as easy as
possible.
1.) Read through the entire Assembly Instructions before you begin.
2.) Choose an area large enough to comfortably lay out all the parts and hardware with enough room to easily
maneuver.
3.) Have an area with a non-abrasive surface where you can lay parts without scratching them.
4.) The Island Grill weighs in at close to 325 pounds. Use caution, and enough people, to remove the Island
Grill from the carton and steel pallet on the bottom.
5.) Lay all parts and hardware out and ensure you have everything listed on the Parts and Hardware page before
you begin assembly. See the Customer Support Page for contact information should any parts be damaged
or missing.
.
.6.) Do not use a Power Screwdriver for assembly as you could strip the threads on the Nuts and Bolts.
.7.) The propane tank for this grill is sold separately. See the LP Gas and Cylinder Information later in this
guide.
BQ06042-1
WARNING
Failure to follow all Danger,
Warnings, and For Your Safety
notices in this Grill Guide may result
in serious bodily injury or death, or in
a fire or an explosion causing damage
to property.
CAUTION
Perform the Leak Test explained later
in this Grill Guide before operating
your grill.
!
!

6
1 Thermometer 36 “U” Main Burner 77Silicon Stopper for Countertop
2 Silicon Stopper For Hood 37 Heat Shield-Control Panel Inner 78Left Side Table
3 Hood Bolt 38 Burner Support Rail 79 Decorative Panel
4 Hood 39 Smoke Drawer Cover 80Cabinet Left-Top-Back Panel
5 Hood Handle Seat 40 Electronic Ignition Button 81Firebox Support-Left
6 Hood Handle 41 Flame Sensor 82Cabinet Left-Back Panel
7 Side Burner Top Frame 42 Back Burner Electrode 83Cabinet Front Support - Top
8 Side Burner Cover 43 Rotisserie Motor Support 84Cabinet Left Panel Support
9 Side Burner Inside Frame 44 Rotisserie Spit Support 85Ice Chest Drawer Glide Mounting
10 Side Burner Grate 45 Back Burner Gas Pipe 86Ice Chest Drawer
11 Side Burner Stem 46 Regulator and Hose 87Ice Chest
12 Side Burner Electrode 47 Rotisserie Spit Storage Support Right 88 Ice Chest Handle
13 Electrode Igniter 48 Rotisserie Spit Storage Support Left 89Ice Chest Drain Plug
14 Back Burner Cover 49 Smoker Drawer 90Ice Chest Liner
15 Back Burner Front Frame 50 Manual Igniter 91Ice Chest Cover
16 Grease Tray 51 Right –Top Drawer 92Ice Chest Cover Handle
17 Grease Tray - Handle 52 Drawer Handle 93Cabinet Front Support-Left
18 Rotisserie Assembly 53 Right Middle Drawer 94Cabinet Front Support-Middle
A. Rotisserie Spit Handle 54 Right Bottom Drawer 95Cabinet Front Support-Right
B. Rotisserie Spit Washer 55 Glide Assembly 96Cabinet Shelf
C. Rotisserie Counterweight 56 Cabinet Right Door 97Cylinder Tray Glide Mounting Bracket-Right
D. Rotisserie Spit Bushing 57 Cabinet Left Door 98Cylinder Tray
E. Rotisserie Fork 58 Locking Caster 99Cylinder Tray Glide Mounting Bracket-Left
F. Rotisserie Spit 59 Caster 100Cylinder Support Ring
19 Firebox Front Panel 60 Locking Swivel Caster 101Cylinder Tray Stopper
20 Gas Manifold Assembly 61 Swivel Caster
21 Control Panel 62 Cabinet Front Skirt
22 Rotisserie Motor 63 Cabinet Bottom Panel
23 Control Knob Seat 64 Cabinet Shelf Support
24 Control Knob 65 Cabinet Back Panel Bracket
25 Firebox Rear Panel 66 Cabinet Right-Back Panel
26 Warming Rack 67 Cabinet Right Panel Support
27 Heat Diffuser 68 Cabinet Crossbar
28 Infrared Back Burner 69 Firebox Support-Right
29 Cooking Grate 70 Cabinet Right-Back Support
30 Firebox Back-Top Plate 71 Cabinet Side Panel
31 Firebox - Right Side Panel 72 Cabinet Back Crossbar
32 Firebox Back Panel 73 Cabinet Right-Top-Back Panel
33 Firebox-Left Side Panel 74 Towel Bar Handle
34 Bottom Heat Shield 75 Countertop Frame
35 Heat Shield 76 Granite Countertop Insert
Detail Parts List - Not Shown In Diagram
102Grill Cover 105Control Knob Allen Screw 108Side Burner Cover Bolt and Nut
103Main Burner Screw 106Rotisserie Thumbscrew 109 AA Battery
104Handle Bolt 107Towel Bar Screw
BQ06042-1 Detail Parts List

8
BQ06042-1 Assembly Parts List
4. Rotisserie Spit with
Handle..…1PC 7.Rotisserie
Motor -1Pc
5.Meat Fork - 2 Pcs 6.Counterweight - 1 Pc
BQ06042-1 Assembly Hardware List
A. “AA” Size Battery – 1 Pc B. Spit Washer – 2 Pcs
C. Spit Bushing – 1 Pc
Heat Diffuser ---3 PCS Warming Rack --- 1 PC Towel Bar Handle-----2 PCS
Small Cooking Grate…2PCS
Large Cooking Grate...1PC
WARNING
Always wear protective gloves when assembling your grill.
!

10
STEP 3 – Insert the 3 Cooking Grates into the firebox. There are 2 small and 1 large cooking grates.
They can be inserted in any order.
STEP 4 –Insert the Warming Rack into the upper sides of the firebox. Be sure the sides of the
warming rack fit down into the slots to secure it in place.

11
STEP 5 –Slide the Rotisserie Motor onto the mounting bracket on the right side of the firebox
sidewall. Note: We recommend you store the Rotisserie Motor in one of the drawers when not in use.
Do not use the Rotisserie Motor in rain or expose to moisture.
STEP 6 –Assemble the Rotisserie Spit in the following order. Slide one spit washer onto the spit and
screw up next to the spit handle. Then slide on the counterweight, followed by the second spit washer.
Tighten the second spit washer to secure the counterweight. Next slide on the spit bushing. Finally slide on
both meat forks with the forks facing each other. Secure them to the middle of the spit by tightening their
thumbscrews. Use caution as the forks are sharp.
Insert 1 Insert 2

12
STEP 7 –Slide the Spit Assembly into place by inserting the pointed end into the rotisserie motor
(Insert 2) and placing the bushing into its bracket on the left firebox sidewall (Insert1). Note: We
recommend you store the counterweight and Forks in a drawer when not in use. A holder is located on the
back of the firebox for Spit storage.
STEP 8 –Unscrew the electronic igniter cap. Place the “AA”Battery into the electronic igniter with
the Positive (+) end facing up. Screw the electronic igniter cap back into place on the electronic igniter.
Insert 1 Insert 2
!
WARNING
Do not dispose of batteries in
a fire. Batteries may leak or
explode.

13
STEP 9–Remove any labels and additional packing material from the grill except CSA Label. Be sure to
clean all foam packing material out of all areas.
Congratulations! Your grill is now fully assembled. Please proceed and read the General Information and
Operation portion of the Grill Guide before attempting to hook up the LP gas cylinder or operating your grill.

14
General Information and Instructions
Your new Member’s Mark Island Grill has been designed and manufactured to high quality standards. It will
provide you with many years of enjoyment with a minimal amount of maintenance. Please keep in mind the
following FOR YOUR SAFETY.
OPERATION
1. Your gas grill requires reasonable care during operation. It will be hot during cooking and cleaning.
You should never leave the grill unattended or move the grill when in use.
2. Children should never use your gas grill. Keep younger children and pets away when in use.
3. Only use your gas grill outside in a well-ventilated area. Never use indoors in any building, garage,
shed, or under any type of flammable canopy or overhang.
4. Ensure your grill is on level ground and the locking casters are locked before use.
5. Turn all gas valves off should the burners go out when cooking. Open the lid and wait 5 minutes before
relighting.
6. Do not lean over the grill or touch the edges of the firebox or lid when in use.
7. Turn the burners off, close the lid, and shut off the LP cylinder should a grease fire occur.
8. Do not obstruct the flow of combustion and ventilation air to this grill.
9. Keep the ventilation openings of the cylinder enclosure free and clear from debris.
10. Keep the outdoor cooking gas appliance area clear and free from combustible materials, gasoline, and
other flammable vapors and liquids.
11. Do not put a barbecue cover or other flammable material in the storage area of this grill.
12. Do not use charcoal briquettes, lava rock, or any type of ceramic product in this grill.
LP Gas and Cylinder Information
Your new gas grill operates on LP (Liquid Propane) Gas. It is odorless, colorless, and non-toxic when produced.
You can smell LP gas as it has been given an odor similar to rotten cabbage for your safety.
Your grill uses the newest and safest LP Gas Cylinder.
1. A listed O.P.D. (Overfill Protection Device) must be used. This prevents
accidental gas leaks caused by overfilling of the tank. Each tank contains
a float that closes the input valve when the tank is 80% full. This allows
room for the LP gas to expand in hot temperatures. A triangular hand
wheel distinguishes this type of tank.
2. Q.C.C.1 Type 1 Quick Connect Valve – provides fast tank hook-ups and requires only to be tightened by
hand. Large external threads on the outlet part of the valve distinguish this.
In addition, the LP tank you use with your grill must meet the following requirements
1. Required Measurements: 12-1/2” (317mm) in diameter and 18-1/2” (472mm) in height.
2. 20-pound (9.1kg) propane cylinder.
3. Constructed and marked with U.S. Department of Transportation (D.O.T.) for the US or CAN/CSA-
B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, for
Canada.
4. A safety release valve.
5. A means for vapor withdrawal.
6. A collar to protect the tank valve.
7. A bottom ring for mounting.
Triangular Hand Wheel
WARNING
Do not attempt to use a cylinder with any other type of connection device.
!

15
LP CYLINDER FILLING AND EXCHANGE
Some areas only allow you to exchange your empty cylinder for a replacement that is already full. Other areas
allow you to refill your cylinder. If you are in an area where you can refill your cylinder:
1. Use only a licensed dealer.
2. The dealer must first purge a new cylinder before filling.
3. Never fill a cylinder more than 80% full by weight. Volume will vary by temperature. An empty
cylinder weighs approximately 18 pounds (8.2kgs).
4. Be sure the LP dealer checks the cylinder for leaks after filling.
5. Do not release LP gas into the atmosphere, as it can unexpectedly ignite when mixed with air.
6. Contact a LP dealer to remove LP gas from a cylinder.
7. Only exchange your cylinder for one with an O.P.D. feature as shown above.
LP CYLINDER LEAK TEST
A leak test should be done each time a cylinder is refilled or exchanged. Do
not smoke or use any type of flammable material in the area during this leak test.
Do not use an open flame to check for leaks.
1. Test outside in a well ventilated area.
2. Use a paintbrush and a solution of 50% liquid soap and 50% water. Do
not use cleaning agents and they can damage the fuel supply parts.
3. Brush liquid onto areas highlighted with arrows.
4. Bubbles indicate a leak.
WARNING
1. Never store any extra cylinders under or near your grill.
2. Never fill your cylinder over 80% full by weight. This may cause release of gas from the safety relief
valve.
3. If the information in points 1 and 2 above is not followed exactly, a fire causing death or serious injury
may occur.
DANGER
Bubbles indicate a leak. In that case, call your LP dealer or fire department immediately.
FOR YOUR SAFTY
1.) The gas supply must be turned off at the LP gas supply cylinder when this gas grill is not in use.
2.) Storage of this gas grill indoors is permissible only if the cylinder is disconnected and removed from the
gas grill.
3.) Cylinders must be stored outdoors out of reach of children and must not be stored in a building, garage, or
any other enclosed area.
WARNING
A frosty cylinder valve indicates possible gas overfill. Close the LP valve and call your dealer immediately.
!
!
!
!

16
TRANSPORTATION AND STORAGE
1. Place dust cap on cylinder valve outlet whenever the cylinder is not in use.
Only install the type of dust cap on the cylinder valve outlet that
is provided with the cylinder valve. Other types of caps or plugs
may result in leakage.
2. Always transport in an upright position.
3. Do not smoke when transporting your cylinder.
4. Keep cylinders out of direct sunlight and away from sources of heat.
Your regulator is equipped with a Q.C.C. Type 1 quick connect system. It will not allow gas to flow until a
positive seal has been made. It has a flow-limiting device that will restrict the flow of gas to 10 cubic feet per
hour (0.28 cubic meters per hour).
TO PLACE THE CYLINDER INTO THE GRILL CABINET
1. Place the tank onto the sliding LP cylinder tray.
2. The front of the tank valve should face to the front of the cabinet.
3. Unhook the LP cylinder support ring and lower it down over the
neck of the LP cylinder. Reattach the hook to secure.
4. Lock the LP cylinder tray in place by turning the LP cylinder
tray stopper to a right angle.
TO CONNECT THE CYLINDER TO THE REGULATOR AND HOSE
1. Be sure the LP cylinder is “OFF” by turning the hand wheel clockwise
until it stops.
2. Place the cylinder into the base cabinet shelf of the grill with the valve
facing outward and secure with the cylinder retaining bolt.
3. Be sure all burner controls are turned to the “Off” position.
4. Remove the safety cap from the cylinder valve.
5. Center the nipple of the regulator into the cylinder
6. Turn the black nut clockwise until it stops. Hand Tighten Only.
Do Not Use A Wrench.
Dust Cap
CAUTION
The pressure regulator and hose assembly provided with this gas grill must be used. This regulator is set for an
outlet pressure of 11 inches water column. Replacement pressure regulators and hose assemblies must be those
specified in the parts list.
!
Regulator and LP Cylinder Connections

17
LEAK TESTING THE REGULATOR, VALVES, HOSES, AND CONNECTIONS
1. Ensure the LP cylinder valve and all burners are “Off”.
2. Ensure the LP cylinder is connected to the regulator.
3. If the information in 1 & 2 is not followed exactly, a fire causing death or serious injure may occur.
4. Mix up a solution of 50% water and 50% liquid dish soap. Do not use any household cleaner
solution.
5. Open the LP tank valve by turning the hand wheel counterclockwise one turn. If you hear a rushing
sound, turn the gas off immediately. In that case, there could be a leak at the connection. Reconnect
the cylinder to the regulator.
6. Spray or brush on the solution covering the following areas: cylinder welds, regulator and cylinder
connection, gas hose connection to the regulator, gas hose, and the gas hose connection to the gas
manifold assembly.
7. Growing bubbles on any of the parts and connections listed above indicate a gas leak. Immediately
shut off the LP tank valve by turning the valve clockwise. Retighten the connections or order
replacement parts as needed. Continue to test as necessary until no leaks are detected.
8. Close the LP tank valve by turning the hand wheel clockwise.
Center this nipple of the
regulator into the cylinder
valve.
The regulator must enter the
cylinder valve in a straight
line.
WARNING
1. DO NOT USE THE GRILL if you cannot stop a leak. Be sure the LP cylinder valve is
closed. If the LP cylinder is still leaking, contact your LP dealer or local fire department.
2. Do not use any match or open flame, or smoke, during leak testing.
3. Do not light a burner during leak testing.
4. The replacement hose assembly must be the one identified.
Q.C.C.1 Type 1 Connector
WARNING
1. Do not connect this grill to any unregulated sources of propane.
2. Before each use, check the gas hose for excessive abrasion or wear, or cuts. Replace a hose
assembly showing those signs with the hose assembly specified in the parts list before using the
grill. Inspect the hose assembly by opening the cabinet door underneath the side burner and
following the regulator hose up to its connection to the gas manifold assembly.
3. Always perform the Leak Test listed below before using your grill for the first time, if the cylinder
has been changed, any gas components have been changed, the regulator flow-limiting device has
been activated, or after a long period of non-use.
4. Do not attempt to connect this grill to the LP system of a motor home or trailer.
!
!
!
WARNING
Always keep the gas cylinder in the
upright position all the time

18
Grill Placement
Grill Operations
BEFORE AND AFTER LIGHTING
1. Ensure your grill is located on a level surface.
2. Lock the locking casters by pressing or turning the locking lever on the casters counterclockwise before
use. Unlock by turning or pressing the locking lever on the casters clockwise.
3. Keep the gas grill area clear and free from combustible materials, gasoline, and
other flammable vapors and liquids.
4. Ensure nothing is obstructing the flow of combustion and ventilation air.
5. Ensure the ventilation openings of the cylinder enclosure are free and clear of debris.
6. Visually check burner flames.
LIGHTING THE MAIN BURNERS WITH PUSH AND TURN IGNITION
1. Open the lid.
2. Ensure all burner control knobs are in the “Off” position.
3. Turn on the LP gas by slowly turning the hand wheel on the cylinder valve.
4. Push in the burner control knob of the burner you wish to light
and turn left to “HI/LIGHT”. You will hear a click as a spark is sent
to the burner. If the burner does not light, then turn back to “Off”,
and repeat this procedure. Continue this process until the burner
lights.
5. Use the Manual directions if it still will not light.
6. When lit, turn the burner control knob to its desired heat setting.
! FOR YOUR SAFETY!
1. Minimum clearance required from sides
and back of unit to adjacent combustible
construction is 24 inches (61 cm).
2. Do not locate or use this outdoor cooking
gas appliance under overhead
combustible surfaces.
APARTMENT RESIDENTS
Check with your apartment manager regarding
your regulations for barbecues.
WARNING
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off, wait 5 minutes and repeat
the lighting procedure
Do not face the grill directly into the wind
Keep any electrical supply cord and the fuel
supply hose away from any heated surfaces
and water.
!
Main Burner
24"(61cm)
24"(61cm)

19
MANUALLY LIGHTING THE MAIN BURNERS WITH THE MATCH HOLDER
1. Open the lid.
2. Ensure all burners are in the “Off” position.
3. Slowly turn on the gas at the LP cylinder valve if it is not already on.
4. Place a match in the Match Holder. This is located in the top center
drawer of the grill cabinet underneath the right main burner.
5. Use the holder to slide the lit match though the cooking grates and the
front of the heat tent to the left of the burner you wish to light.
6. Press and turn the burner control knob to “HI/LIGHT”. Continue to push
in and hold up to 5 seconds or until the burner lights.
7. If the burner does not light within 5 seconds, turn the burner control
knob to “Off”. Wait 5 minutes for gas to clear, and try again.
8. When lit, turn the control knob to the desired heat setting.
LIGHTING THE BACK OR SIDE BURNERS WITH ELECTRONIC IGNITION
1. Open the lid or side burner cover
2. Ensure the burner control knob is in the “Off” position, as well as any
main burners not in use.
3. Slowly turn on the gas at the LP cylinder valve if it is not already on.
4. Push in and turn the appropriate burner control knob to “HI/LIGHT”
and hold in.
5. Depress the electronic ignition button and hold. You should hear a
clicking sound, which shows the electronic ignition is working.
6. If the burner does not light within 5 seconds, turn the burner control
knob to “Off”. Wait 5 minutes for the gas to clear, and repeat the
above procedure. Use the Manual directions if it still will not light.
7. For the back burner, continue to push and hold the burner control knob in for 5 to 7 seconds after the burner
lights until the flame sensor begins operating. Letting up on the burner control knob before a high enough
temperature has been reached may cause the flame sensor to shut off fuel to the back burner.
8. When lit, turn the burner control knob to its desired heat setting.
MANUALLY LIGHTING THE SIDE BURNER OR BACK BURNER
1. Open the lid or side burner cover.
2. Ensure the side and back burner control knobs are in the “Off”
position as well as any main burner not in use.
3. Slowly turn on the gas at the LP cylinder valve if it is not already on.
4. Place a match in the Match Holder if lighting the back burner. This
is located in the top center drawer of the grill cabinet underneath the
right main burner.
5. Strike the match, and place near the top of the burner if lighting the
side burner or near the center of the back burner if lighting the back
burner..
6. Push in and turn the appropriate burner control knob to “HI/LIGHT”
and hold in.
7. If the burner does not light within 5 seconds, turn the burner
control knob to “Off”. Wait 5 minutes for the gas to clear, and try again.
8. For the back burner, continue to push and hold the burner control knob in
Electric Igniter
Back Burner
Side Burner

20
for 5 to 7 seconds after the burner lights until the flame sensor begins operating. Letting up on the burner
control knob before a high enough temperature has been reached may cause the flame sensor to shut off fuel
to the back burner.
9. When lit, turn the burner control knobs to their desired heat setting.
TURNING OFF YOUR GRILL
1. Turn all burner control knobs to the “Off” position.
2. Turn off the gas supply at the LP tank by turning the valve clockwise.
Cleaning and Maintaining Your Grill
STAINLESS STEEL SURFACES AND OTHER EXTERIOR SURFACES– wash with a mild dish soap
and warm water. A cloth, soft brush, or plastic cleaning pad can be used. Rinse thoroughly and wipe dry. The
stainless steel used in the construction of your grill is 304 commercial grade. There are many specific stainless
steel cleaners available. Follow the manufacturer’s directions. Always polish in the direction of the lines. Do
not allow dirt and grease to accumulate. Do not use steel wool, as it will scratch the surface.
In addition, the following products and naturally occurring substances
in the outdoors will damage all stainless steel finishes. Use caution so that they do not come in contact with
your Gas Grill. Immediately wash them off and dry the stainless steel should they ever come in contact with
your Gas Grill. This includes, but is not limited to, Pool Chemicals (chlorine and bromine), Lawn Fertilizer, Ice
Melting Salts, Sea or Salt Water, Urine, Bird Droppings, and Tree Sap.
COOKING GRATES, WARMING RACK, AND HEAT DIFFUSERS – use a stiff brass brush. Wash with
warm water and mild dish soap as needed, rinse, and dry.
GREASE PAN AND TRAY – check after each use. Remove and empty the Tray when half full. Remove and
clean the Pan as grease builds up. Both can be washed with warm water and mild dish soap.
ELECTRONIC IGNITER – visually inspect for cracks. Replace if a crack is found. Do not use water to
clean the igniter.
BURNERS – we recommend you clean your burners at least twice a year, or before use if the grill has not been
used in over one month.
WARNING
1. Do not clean any part of your barbecue grill in a self-cleaning oven.
2. Do not use oven cleaners, abrasive kitchen cleaners, cleaners that contain citrus products, or mineral
spirits.
3. Do not use any type of steel bristled brush.
4. Clean your grill regularly to prohibit grease build-ups and avoid a grease fire or excessive flare-ups.
5. Always wear protective gloves when cleaning your grill.
!
WARNING
Small insects, such as spiders, are able to access the burner tubes. Sometimes they will build nests or spin
webs. In either case, this can block or reduce the amount of gas flowing through the burner. You will
usually see a smaller flame, or a flame that is mostly yellow rather than blue, coming from the burner when
this happens. Other signs include the gill not heating evenly, not reaching temperature, or burners not
igniting. In cases with severe blockage, this can cause the flame to burn backwards, and outside of the
burner tubes, which can cause damage to your grill and/or personal injury. IMMEDIATELY SHUT OFF
THE FLOW OF LP GAS AT THE CYLINDER BY TURNING THE HAND WHEEL
CLOCKWISE SHOULD THIS HAPPEN. Wait for the grill to cool, and then clean all burners. Your
grill may be stored indoors only if the LP cylinder is disconnected and removed from the appliance.
!