Mercia Garden Products SI-002-001-0007 User manual
!
x2
2mm Drill bit
12mm CSK
1!
2!
3!
50kg
¡
¢
£
Playhouse Options:
Take a look at the dierent playhouse options below which refers to the instruction
leaets required to build each option.
5x5 Playhouse With Half Glazed Door,
Tower & Slide
SI-002-001-0007
5x5 Playhouse With Half Glazed Door,
Tower, Slide & Swing
SI-002-001-0008
02DTSHAX05051W-V1-PEFC (Playhouse)
02DTTWR6565-V1-PEFC (Tower)
02PATINCSWA-V1-PEFC (Swing Set)
02DTSHAX05051W-V1-PEFC (Playhouse)
02DTTWR6565-V1-PEFC (Tower)
5x5 Playhouse With Framed Door, Tower &
Slide
SI-002-001-0024
5x5 Playhouse With Framed Door, Tower,
Slide & Swing
SI-002-001-0025
02DTSHAX05051W-V1-PEFC (Playhouse)
02DTTWR6565-V1-PEFC (Tower)
02PATINCSWA-V1-PEFC (Swing Set)
02DTSHAX05051W-V1-PEFC (Playhouse)
02DTTWR6565-V1-PEFC (Tower)
5x5 Playhouse With Boarded Door, Tower
& Slide
SI-002-001-0024
5x5 Playhouse With Boarded Door, Tower,
Slide & Swing
SI-002-001-0025
02DTSHAX05051W-V1-PEFC (Playhouse)
02DTTWR6565-V1-PEFC (Tower)
02PATINCSWA-V1-PEFC (Swing Set)
02DTSHAX05051W-V1-PEFC (Playhouse)
02DTTWR6565-V1-PEFC (Tower)
5x5 Playhouse With Half Glazed
Door, Tower & Slide
5x5 Playhouse With Half Glazed Door, Tower,
Slide & Swing
5x5 Playhouse With Framed Door,
Tower & Slide
5x5 Playhouse With Framed Door, Tower, Slide &
Swing
5x5 Playhouse With Boarded Door,
Tower & Slide
5x5 Playhouse With Boarded Door, Tower, Slide &
Swing
Model Build Instructions Required
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Overall Dimensions:
Width = 1984mm
Depth = 1923mm
Height = 1625mm
2
1
4
5
3
6
8
7
9
Ladder Step QTY 4
PRO2758-390mm
Corner Braces - 44x58x762mm QTY 8
F4458-G-802mm (762mm nished length)
Front Post - 70x70x1625mm QTY 2
PI-04-0017
Rear Post - 70x70x900mm QTY 2
PI-04-0018
Additional Items required for Slide:
Front Saftey Board QTY 1
PI-03-0204
Side Safety Board QTY
PI-03-0203
Slide Framing - 75x75x555mm QTY 1
F7575-555mm
12
13
14
11
Small Rail QTY 1
AI-02TCR416X543-V1
Part not required if purchased slide
Platform QTY 1
AI-02TB1470X1983-V1
Large Rail QTY 1
AI-02CR1331X543-V1
Ladder Side Right - 27x95x1365mm QTY 1
PRO2795-1365mm
Ladder Side Left - 27x95x1365mmQTY 1
PRO2795-1365mm
10
Ladder Block - 44x44x372mm QTY 1
F4444-372mm
Slide QTY 1
PI-10-0001
Building Content:
60mm Screw x 2
50mm Screw x 33
40mm Screw x 24
30mm Screw x 8
150mm Screw x 8
100mm Screw x 19
Nail Bag
Pre Assembly
Before assembling remove the transportation
blocks from the bottom of each panel.
Take care removing the blocks as to not damage
the panels. Tap with a at headed screwdriver
and hammer.
Dispose of the blocks once removed.
8
150mm
screw
Step 1
Parts needed - &
Place the platform (No.1) face down
on a level surface, place the two rear
posts (No.8) in the two corners
shown. Secure with 150mm screws
directed through the platform into
the end of the post.
Ensure the platform is supported
throughout the construction
process.
4 x 150mm screws
1
1
8
8
181! 2!
Pre drill
hole
Step 2
Parts Needed - & &
Place a corner brace (No.7) up
against the platform (No.1) and
the rear post (No.8) Ensure that
the corner brace is sitting from the
post and the platform. If you do
not ensure the correct angle the
platform may be out of square.
Once you have the correct angle x
the corner brace to the platform
and the base using a 100mm
screw.
2 x 100mm screws
7
100mm
screw
7
871
1! 2!
Pre drill
hole
Step 3
Parts needed -
Measure the distance from the
edge of the corner brace (No.7) up
to the post from both ends, both
measurments should be the same.
Make a note of the exact
measurment and you can then use
this as a guide for all the corner
braces.
Pencil mark where the corner
braces should sit based on the
measurment already taken. Fix a
further three corner braces using
the same method as above.
6 x 100mm screws
100mm
screw
7
7
7
71! 2!
Pre drill
hole
Step 4
Part needed - & &
Place the front post (No.9) next
to the rear post (No.8) ensuring
the end sits ush with the
platform (No.1) and make a
pencil mark on the front post
where the rear post nishes.
Make sure you do this for both
front posts.
981
9
1! 2!
Pre drill
hole
9
Step 5
Part needed - &
With some help, tip the platform
(No.1) on it’s side. Place the front
post (No.9) within the cut out on the
platfrom, make sure the pencil mark
lines up with the top of the platfrom
framing.
Once you are happy the front post is
lined up correctly t a 150mm screw
through the post into the platform,
do this from the two available sides
ensuring the screws are staggered
and do not clash.
2 x 150mm screws
150mm
screw
1 9 1! 2!
Pre drill
hole
871
Step 6
Part needed - & &
Use the measurment taken
previously for the corner braces
(No.7) and using a pencil mark out
where the corner braces need to sit
on the platform (No.1) and the front
post (No.9)
Fix the two corner braces in place
using 100mm screws.
4 x 100mm screws
100mm
screw
7
7
1! 2!
Pre drill
hole
9
Step 7
Parts needed - &
With some help tip the platform
(No.1) round to the other side.
Place the remaining front post
(No.9) within the cut out on the
platfrom, make sure the pencil
mark lines up with the top of the
platfrom framing.
Once you are happy the front post
is lined up correctly t a 150mm
screw through the post into the
platform, do this from the two
available sides ensuring the screws
are staggered and do not clash.
2 x 150mm screws
150mm
screw
191! 2!
Pre drill
hole
1
Step 8
Parts needed - & &
Use the measurment taken
previously for the corner braces and
using a pencil mark out where the
corner braces (No.7) need to sit on
the platform (No.1) and the front
post (No.9)
Fix the two corner braces in place
using 100mm screws.
4 x 100mm screws
100mm
screw
7
791! 2!
Pre drill
hole
Step 9
Part needed -
With some help tip the platfrom
(No.1) the right way around
ready for the playhouse to be
assembled.
Fix the oor sheet provided in
the playhouse directly to the
platform not to the oor joist.
Follow the steps on the seperate
set of instructions to construct
the playhouse.
20 x 40mm Screws
40mm
screw
1
1
1! 2!
Pre drill
hole
50kg
Once you have nished constructing the
playhouse you can now continue to
nish the tower. This particular
playhouse has been used for illustrative
purposes.
Step 10
Parts needed -
Place the large rail (No.2)
between the two front posts
(No.9) ensuring the front of the
rail nishes ush with the front
of the posts. Fix the rail in place
with 8x50mm screws.
8 x 50mm screws
50mm
screw
2
1! 2!
Pre drill
hole
50kg
2
9
9
4
5
6
Step 11
Parts needed - & &
To construct the ladder ensure you
pre-drill all holes and using
16x50mm screws attach each step
(No.6) to the ladder sides (No.3 & 4).
16 x 50mm screws
50mm
screw
4 65
1! 2!
Pre drill
hole
If slide is purchased,
position the slide on the
opposite side to the door
as shown in the diagrams.
1! 2!
Pre drill
hole
50kg
Step 12
Parts needed -
To position the Ladder Block
(No.10), measure 27mm from
upright. This is where the block will
be xed wth 2x60mm screws.
2x60mm screws
60mm
screw
10
10
¡
Step 13
Part Needed -
Place the ladder between the
front post (No.9) and the
playhouse left hand side rail.
Ensure the ladder ts ush
with the post and the
playhouse rail, x in place
using 4x50mm screws as
shown.
4 x 50mm screws
50mm
screw
9
9
1! 2!
Pre drill
hole
50kg
If slide is purchased, position
the slide on the opposite side
to the door as shown in the
diagams.
Step 14
Parts needed -
If you have purchased the slide
skip this step and go straight to
step 14.
If you have not purchased the
slide then this is your nal step.
Place the short rail (No.3)
between the front post (No.8) and
the playhouse side panel. Fix the
rail in place with 5x50mm screws.
5 x 50mm screws
50mm
screw
3
31! 2!
Pre drill
hole
50kg
Step 15
Parts needed -
This and all further steps are for when
a slide has been purchased.
Attach the slide framing (No.13) to the
side of the platform with 3x100mm
screws level with the top of the platform.
3 x 100mm screws
100mm
screw
Note:
We recommend applying an impact reducing
surface around the base and slide, also a 2
Meter safety perimeter should be set up
around the building free from obstacles and
potential hazards.
13 1! 2!
Pre drill
hole
50kg
If slide is purchased,
position the slide on
the opposite side to
the door as shown in
the diagrams.
13
Note if tting slide
1. Please keep this instruction sheet safe for future reference.
2. Inappropriate use or faulty application of the product is explicitly forbidden and absolves
the manufacturer of all liability.
3. The assembly must be done by an adult.
4. All elements of the item should be inspected regularly for eventual wear.
5. This product meets to all safety aspects of the European standard EN71. It is only suitable
for domestic use, both indoors and outdoors.
6. The product must be installed onto a playframe that is suitable for this activity (e.g. a
wooden tower). The assembly must be carried out in such a way that head, nger and
clothing entrapments are excluded. In order to prevent clothing entrapments during
gliding, there should be no openings around the platform between 3mm and 25mm. Pay
special attention to the boards of the platform onto which the slide is mounted.
7. When mounting or assembling the product attention should be given to minimum required
distance between the product and eventual obstacles: walls, fencing,... The distance should
be minimum 2000mm.
8. In this safety area no hard, angular or pointed objects should be present. The surface
underneath the product should be at and shock absorbing, so no asphalt, concrete
or any other hard surface.
9. The product must be mounted onto a suitable platform (see point 6) and only in accordance
with the recommended platform height with a tolerance of approximately 50mm (see notes
at the rear of the slide). The assembly must be done with 5mm or 6mm gauge countersunk.
The ground level surface must be suuciently stable to avoid subsidence and to ensure that
the slide does not get damaged.
10. It is strongly advised not to lift the slide from the bottom after it has been xed to the
platform.
11. To avoid the heating up of the product, do not orient the sliding surface towards the sun.
12. Sliding can cause a small electrostatic charge. This can be avoided by not wearing synthetic
fabric clothing and/or by regularly cleaning the surface of the slide with water and soap.
Step 16
Parts needed -
Position the slide (No.14) on top
of the platform and the slide
framing (No.13), ensure the slide
is pushed right up to the slide
frame and x to the platform with
2x40mm screws.
2 x 40mm screws
40mm
screw
14
4!
1! 2!
Pre drill
hole
50kg
14
If slide is purchased, position
the slide on the opposite side
to the door as shown in the
diagrams.
Step 17
Parts needed - &
The safety boards (No.11 & 12)
are positioned to block the gaps
on the tower’s rails and stop
entrapment when going down
the slide. Fix them in place using
4x30mm screws per board.
8 x 30mm screws
30mm
screw
11 12
1!
Pre drill
hole
4!
12
11
2!
50kg
It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.
AFTER TREATMENT:
score around protective
cover on glazing and
carefuly peel
covering back
£
£
£
£
¡
£
¤
£
££
¤
¢
¢
¥
£¤
¤
¦
1
2
3
4
5
6
7
8
9
¥
§
§
§
¦
¨£
2
§
1
§
§
3
4
§
©
¢
£
ª
£
£
¦
¢
«
¤
¦
12
£
§
£
£
¦
¢
«
¤
This manual suits for next models
3
Table of contents
Other Mercia Garden Products Play Set & Playground Equipment manuals
Mercia Garden Products
Mercia Garden Products 0SNO0705-V3 Instruction manual
Mercia Garden Products
Mercia Garden Products 02ROCK0606-V1-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products 02HON51156-V2-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products 02CHYTWR-V2 User manual
Mercia Garden Products
Mercia Garden Products 02PLAY511511-V2-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products Chestnut User manual
Mercia Garden Products
Mercia Garden Products 02LRGTWR-V1 User manual
Mercia Garden Products
Mercia Garden Products 02SNO0705-V4-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products 02DORM0707-V1 User manual
Mercia Garden Products
Mercia Garden Products 02HON51156-V1 User manual
Mercia Garden Products
Mercia Garden Products 02DTSHAX0606SFHD2W-V1-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products 02PLM0404-V1 Instruction manual
Mercia Garden Products
Mercia Garden Products 02PENTPLAY-V2-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products Poppy Instruction manual
Mercia Garden Products
Mercia Garden Products Dorma Playhouse User manual
Mercia Garden Products
Mercia Garden Products 02TWR-V2-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products SI-002-001-00109 Instruction manual
Mercia Garden Products
Mercia Garden Products 02DTTWR0707-V1-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products 02PIP0605-V1 Instruction manual
Mercia Garden Products
Mercia Garden Products 02BRAM0806-V2 Instruction manual
Mercia Garden Products
Mercia Garden Products 02BRAM0806-V3-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products TULIP PLAYHOUSE 02TUL411411-V3-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products 02DTTWR6565-V1-PEFC User manual
Mercia Garden Products
Mercia Garden Products 02DTSHPN0606SFD2W-V1-PEFC Instruction manual
Popular Play Set & Playground Equipment manuals by other brands
AGame
AGame MSC-4552 Assembly instructions & user manual
Ledon
Ledon Basic Bing Assembly instructions
KidKraft
KidKraft HAMPTON PLAYSET Installation and operating instructions
Swing-N-Slide
Swing-N-Slide Wrangler Assembly instructions
BOERPLAY
BOERPLAY Bird's nest swing Anti-wrap H2.12 manual
BOERPLAY
BOERPLAY PSTE110.064 manual
Jungle Gym
Jungle Gym Jungle Palace 2.1 Assembly instructions
Eastern Jungle Gym
Eastern Jungle Gym BOTTOM PLAYHOUSE Assembly instructions
BOERPLAY
BOERPLAY Roundabout 2 SOLE030.161 manual
Zupapa
Zupapa Dome Climber user manual
SPORTSPOWER
SPORTSPOWER JET MAT MSC-5019 Assembly and use instructions
Creative Play
Creative Play carousel mini Installation and assembly instructions