Creative Play carousel mini Guide

Installation + Assembly Instructions
REF: CR101 - CAROUSEL MINI
CR102 CR103
pg 1 of 19

REF: CR101 - CAROUSEL MINI
pg 2 of 19
PARTS required
x1 (triangular floor) x1 (square floor)
x1 (triangular floor SLIDE - has a straight edge)
NOT REQUIRED
QTY: 2 (90mm x 90mm) 1 HOLE
(various colour end caps)
MS1a
MS1b
QTY: 2 (90mm x 90mm)
(2 with BLUE end cap)
MS2a
QTY: 2 (90mm x 90mm)
(2 with BLUE end cap)
MS2b
x10 (M12 110* square hex bolt)
x10 (M12 Nylocs)
x10 (End Caps)

REF: CR101 - CAROUSEL MINI
pg 3 of 19
PARTS required continued...
x4 ATTACHMENT Metal Bracket
2 for STAIRS / 2 for WINDOW PLANTER
MB-A
x14 STANDARD Metal Bracket
4 for SNAKE SLIDE / 4 for WINDOW GUARD RAIL / 6 for 123 BOARD
*many parts are pre-assembled with the brackets attached - totals above are for ‘loose’ brackets
MB-S
x1 SQUARE ROOF
(inc 16 roof clips - same colour as roof) x1 STAIRS

REF: CR101 - CAROUSEL MINI
pg 4 of 19
PARTS required continued...
x1
SLIDE ASSEMBLY
x1
THREAD BAR
x1
slide SUPPORT FRAME x1 123 BOARD
x1 TIMBER GUARD RAIL
x1 WINDOW GUARD RAIL x1 WHITE BOARD (with COMBINATION BRACKETS)
x4 PLAYTEC
WASHERS
x1 WINDOW PLANTER

REF: CR101 - CAROUSEL MINI
pg 5 of 19
PARTS required continued...
x16 (80mm brass screws)
x48 (40mm brass screws)
x24 (TORK TAINERS various sizes)
(13 x Thickness to go through = 29mm
4 x Thickness to go through = 36mm
1 x Thickness to go through = 41mm
6 x Thickness to go through = 52mm)
x24 (End Caps)
To be used for TORK TAINERS
TOOLS required

REF: CR101 - CAROUSEL MINI
pg 6 of 19
Foundation Details
SLIDE FOUNDATION
STAIRS FOUNDATION
*MAIN POSTS ARE POSITIONED @ 750mm centres
*attacments such as slide and stairs alter - shown above

REF: CR101 - CAROUSEL MINI
pg 7 of 19
Foundation Details continued...
Slide Details AS SHOWN LEFT
All posts = 600mm depth AS SHOWN RIGHT
*REMEMBER - 600mm below FINISHED GROUND LEVEL - if WETPOUR / MULCH /
PLAYSAFE is to be laid amend as required
SOIL
SLIDE SUPPORT FRAME
CONCRETE
SOIL
TIMBER SUPPORT POST
CONCRETE

REF: CR101 - CAROUSEL MINI
pg 8 of 19
Installation + Assembly Instructions
Construct the main assembly BEFORE laying concrete
foundations STEPS to
11 7/8

REF: CR101 - CAROUSEL MINI
pg 9 of 19
Installation + Assembly Instructions
Position the main support posts & floor assemblies
Using M12 hex bolts, nylocs and end caps
2
*FLOOR FOR SLIDE HAS
A FLAT EDGE
*All triangular
floors/bases attach
to the FLAT FACE of
the support post
All square floors/bases attach to the grooved
side
MS2a = Support for roof - SHORT
MS2b = Support for roof - LONG
All other supports are MS1
MS2a
MS2a
MS2b
MS2b
PLEASE NOTE:
The following pages show images which are not necessarily for the specific version and are used to show
the assembly / installation for the specific component /sub assembly ONLY

REF: CR101 - CAROUSEL MINI
pg 10 of 19
Installation + Assembly Instructions
Attach the SLIDE ASSEMBLY
Attach the STANDARD METAL BRACKETS using NYLOCS, TORKTAINERS & ENDCAPS
*Attach the SLIDE SUPPORT FRAME using
thread bar - This will be -PRE ATTACHED
but not ’fixed’
5
Use 80mm brass screws to secure assem-
bly (STANDARD METAL BRACKETS) to the
main upright supports
STANDARD METAL
BRACKET is positioned in
the centre of the upright
support

REF: CR101 - CAROUSEL MINI
pg 11 of 19
Installation + Assembly Instructions
Attach the STAIRS
Using ATTACHMENT METAL BRACKETS and COMBINED BRACKET using NYLOCS, TORKTAINERS & ENDCAPS
Attach the brackets to the upright supports using 80mm brass screws
Attach the WHITEBOARD
The combined bracket is pre-assembled with the whiteboard
POSITION THE WHITEBOARD as shown below
Use 80mm brass screws for the COMBINED
BRACKET & 40mm screws for the STANDARD
BRACKET
6
7
MB-A
MB-C
80mm brass screws
40mm brass screws
ATTACHMENT METAL BRACKET
10mm from the end of the timber
(timber face)

REF: CR101 - CAROUSEL MINI
pg 12 of 19
Installation + Assembly Instructions
Main assembly complete
Concrete foundations can now be laid OR follow the rest of the instructions then concrete
8
Attach the ROOF
Using 40mm brass screws and roof clips - the colour of the clips corespond to the colour of the ROOF
9
Each post has 2 x clips ABOVE and 2
x clips BELOW
The holes in the roof are SHAPED and should ‘want’ to
position itself at an angle
ROOF IS NOT LEVEL ensure the drawing right is followed
(measurements are from top of PLATFORM / hex board)

REF: CR101 - CAROUSEL MINI
pg 13 of 19
Installation + Assembly Instructions
10 Attach the 123 Board
Using 6 x 40mm brass screws, 6 x STANDARD METAL BRACKETS, tork tainers and 123 Board assembly
TOP VIEW DETAIL
Platform ‘SIDE’
6 x TORKTAINER
Thickness to go
through = 52mm
Out‘SIDE’

REF: CR101 - CAROUSEL MINI
pg 14 of 19
Installation + Assembly Instructions
Attach Timber Guard Rail
Using 40mm brass screws
11
METAL BRACKET is
positioned in the centre
of the upright support
0.00 = TOP of BASE /
HEX BOARD

REF: CR101 - CAROUSEL MINI
pg 15 of 19
Installation + Assembly Instructions
Attach Window Guard Rail
Using 40mm brass screws, NYLOCS, TORKTAINERS & ENDCAPS
12
3 x TORKTAINER @ 29mm
thickness
1 x TORKTAINER @ 41mm
thickness
*Window always faces OUT
- Yellow frame OUTWARDS
(away from platform)
PLAYTEC WASHER

REF: CR101 - CAROUSEL MINI
pg 16 of 19
Installation + Assembly Instructions
Attach the Window Planter
Using 80mm brass screws, NYLOCS, TORKTAINERS & ENDCAPS
13
MB-A
ATTACHMENT METAL BRACKET
10mm from the end of the timber
(timber face)
2 x TORKTAINER @ 29mm
thickness

REF: CR101 - CAROUSEL MINI
pg 17 of 19
Installation + Assembly Instructions
Installation + Assembly COMPLETE
Ensure all END CAPS are present - make any final checks ...
14

REF: CR101 - CAROUSEL MINI
pg 18 of 19
Dimensions

REF: CR101 - CAROUSEL MINI
pg 19 of 19
NOTES:
This space can be used to make any notes relating to installation / assembly of the MINI - pass this sheet back
to PRODUCT DEVELOPMENT to review the notes