Mercia Garden Products 02CHYTWR-V2 User manual

02CHYTWR-V2
MADE IN GREAT BRITAIN
PLEASE RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
For Assistance Please
Contact Customer Care on
01636 880514
x2
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
This building should be erected by
two Adults.
For ease of assembly, it is advisable to
pilot drill all screw holes and ensure
all screw heads are countersunk. We
recommend using a 2mm, 5mm and
8mm drill bit.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Utility knife, wood saw, and
drill with 2mm, 5mm and 8mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
- Make sure you have a suitable base ready to erect your building and is
accessible all the way around to enable any maintenance to be carried out
if needed.
TIMBER
As with all natural materials, timber can be affected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling
of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these
processes cannot be avoided but can be helped. It is suggested that the
outdoor building is sprayed with water during extended periods of warm
sunshine and sheltered as much as possible during rain or snow.
Though this building is supplied pre painted it is recommended to treat the building
annually using wood paint or preserveative which there are a variety of of colours
and stains available.
Annual care and maintenance will ensure the longevity of your
building.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently
tested to EN71 level. We cannot accept responsibility for your safety whilst erecting or using this product.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23
CONTENTS CHECK ALL PARTS LISTED ARE IN THE KIT BEFORE ASSEMBLY
BASE DIMENSIONS
Length - cm
Width - cm
OVERALL DIMENSIONS
Length - cm
Width - cm
Height - 0cm
50mm Screw x 43
40mm Screw x 25
20mm Screw x 5
30mm Screw x 4
10mm Screw x 20
100mm Screw x35
2
1
3
4
5
6
7
8
9
10
11
12
13
14
WARNING: Only for domestic use
Not suitable for children under 36 month
To be used under direct supervision of an adult
Bunk Floor
44x58x1088mm x3
44x58x1870mm x2
28x28x1170mm x2
27x58x1044mm
44x58x523mm x4
27x58x400mm x8
Ladder side Left
Ladder side Right
Ladder Step 27x95x476mm x2
Slide
28x28x1057mm x2
Shiplap board 1200mm
Shiplap board 1112mm x2

STEP 3
Bunk Rail
100mm
screw
4 X 100MM SCREWS
Lift the frame up and position
the leg posts (6) as shown.
Fix the posts to the frame using
100mm screws. Pre-drill holes
first.
6
6
6
6
STEP 4
Place the components as shown
and fix together using 100mm
screws. Pre-drill holes first to
avoid splitting the wood.
16 X 100MM SCREWS
7
Fix a brace (7) to either side of
each leg post using 100mm
screws as shown. Pre-drill holes
STEP 1
STEP 2
43
3
2 X 100MM SCREWS
5
4
4 X 100MM SCREWS
100mm
screw
Place the next set of
components inside the frame
make sure component 5 is
postioned in the center and use
component 5 as a guide for
positioning component 4 in the
middle.
Fix together using 100mm
screws. Pre-drill holes first.
100mm
screw
4

STEP 5
40mm
screw
10 X 40MM SCREWS
1
STEP 6
Place the Bunk Floor on top
and fix into position using 40mm
screws. Pre-drill holes first.
10 X 30MM SCREWS
30mm
screw
Next take out the solid sheet floor
which is supplied with the
playhouse.
Place the floor sheet on top of
the platform and secure into
position using 30mm screws.
Predrill holes first to avoid
splitting the wood.
STEP 7
50mm
screw
12 X 50MM SCREWS
8
9
8
9
Now Place the framing on top of the
floor sheet around the edge as
shown. Fix each piece place into
place using 3x50mm screws per
piece.
Predrill holes first to avoid splitting the
wood.
STEP 8
The platform is ready for the assembly of the playhouse on top. Follow the instructions provided with
the playhouse. Disregard the floor joists as these are not needed when fitting to the platform.
Ensure to place the playhouse on top of the framing mentioned in step 7. Secure the playhouse to this
framing using 50mm screws. Predrill holes first.
8 X 50MM SCREWS

STEP 9
Now slot parts 10 and 11 into the
bottom of the cladding around the
sides. Fix into position using
40mm screws.
Predrill holes first to avoid
splitting the wood.
11
STEP 10
STEP 11
Then place the ladder against the
platform as shown and fix into
position using 100mm screws.
Pre-drill holes first and ensure the
screws go straight through into the
platform framing.
The Ladder can also be
positioned at the front, see step
12.
8 X 50MM SCREWS
50mm
screw
12 14
13
Next assemble the ladder using
the components shown and
finxing with 50mm screws.
Pre-drill holes first.
2 X 100MM SCREWS
100mm
screw
10
11
10
11
40mm
screw
40mm
screw
40mm
screw
12 X 40MM SCREWS

STEP 12
2 X 40MM SCREWS
STEP 13
I
t
i
s
E
S
S
E
N
T
I
A
L
t
h
a
t
y
o
u
a
p
p
l
y
w
o
o
d
t
r
e
a
t
m
e
n
t
i
m
m
e
d
i
a
t
e
l
y
a
f
t
e
r
t
h
e
b
u
i
l
d
i
n
g
h
a
s
b
e
e
n
a
s
s
e
m
b
l
e
d
.
Place the Slide into position
shown and secure using 40mm
screws. Pre-drill holes first.
The position of the ladder and
slide can be reversed to create
an alternative set up if desired.
We adivse not to place either
the ladder or slide on the same
side as the door as this creates
a potential hazard.
x
We adivse not to place
either the ladder or slide on
the same side as the door
as this creates a potential
hazard.
Score around protective cover
on glazing and carefully peel
covering back using a utility
knife.
score around protective
cover on glazing and
carefuly peel
covering back