Mini 807 User manual

807 User Manual

1. PRECAUTIONS
1. Do not expose the camera to dusty, dirty or sandy conditions, if these gets into the
camera or on the lens it can damage the components.
2. Do not expose the camera to high temperatures.
The normal operating of the camera is 0℃to 40℃(32F to 104F).
High temperatures can shorten the life span of electronic device, and extremely high
temperature will shorten the battery and/or degrade the plastic components. Note
extreme temperatures can be achieved in parked cars in direct sunlight.
Expose the dash camera to strong sunlight when using Motion Detection mode may
cause the camera to malfunction or become damaged as the temperature can be too
high in your car in summer.
3. Do not expose the camera to a cold environment.
Extremely low temperatures can also damage the electronic components; if there is
water moisture in cold environment, freezing water can cause damage, as can thawing.
Do not try to dismantle or open the casing. Doing so may result in electrical shock and
will most likely result in damaging the camera.
4. Do not mistreat the camera, dropping, sudden impact, and vibration can cause
damage.
5. Do not clean the camera with chemicals, cleaning solution or a high concentration
detergent. Only a slightly damp cloth should be used.
6. Before using, please format the cards in the camera or computer to avoid some
unnecessary troubles; the cards also need to be formatted regularly. (see 6.36)
7. There may be a layer of plastic film on the LCD screen and the lens ,which is tended to
prevent any scratch when transportation. In the case,please remove the protective film
of lens before using, maybe you can keep the protective film on screen, it’s okay.
8. The camera use built-in supper capacity to get power from the car, due to the charge
time is a little long (about 10 seconds), first time to connect with computer, camera
maybe can’t connect with the computer or computer can’t detect a USB flash, which
are normal in the first time, please pull out the plug and re-plug USB cable to
computer, everything will go to normal.
9. Camera only start to record automatically when car engine is started . Camera can not
record when ACC power on.

2. ACCESSORIES
Before using this product, please make sure that your camera package consists of all the
following items . Please contact the distributor in case of any loss.
Name
Quantity
Name
Quantity
Camera
1 piece
Car Charger
Optional
USB cable
1 piece
3M sticker
4 pieces
Cable Clip
1 bag (6 pieces)
User Manual
1 piece
Film
2 pieces
Lens Cleaning Cloth
1 piece
CPL Filter
optional
GPS
optional
CPU (mount)
optional
Gift box
1 piece
OBD II cable
optional
CPL Filter (optional): Reduce the reflection from shiny surface like vegetation, sweaty skin,
water surface, glass, road, and let the natural color come through at the same time. Some
of the light coming from the sky is also polarized to give a more dramatic sky and high
contrast clouds, rendering outdoor scenes crisper the deeper color tones. Align the white
line on CPL with the dot on camera will bring the best reflection reducing effect.
Methods of pasting the FILM:
1. Spray some water on the place that the FILM will be pasted on, and then use a dry
towel to clean it;
2. Tear off the FILM, and then paste it to the right place.
3. After you have adjusted the location well, you can use a scratch board or something
else flat to slick the film and squeeze the water inside out until there is no bubble or
water in it.
4. Then put 3M sticker onto the film, then if you want to remove bracket, it is easy, just
remove the FILM.

3. MAIN FEATURES
A: Small and delicate design, install behind the rear view mirror, that will not block your
sight, don’t effect the safety of driving. If user want to check the videos or connect with
computer to check the files, he can remove camera from the windscreen at any time.
B: This camera use the best Ambarella A7 DSP chip-set,the best high definition video
images in low bit rate.
C: Use most excellent sensor manufacturer Sony’s latest IMX 322 sensor, best 6G IR lens,
to achieve the most perfect effect of low illumination image at night.
D: User can choose to get power from OBD via OBD II cable, to achieve real Parking
Guard function.
E: we use the super capacity for backup power when car engine stop, not battery inside
the camera, so do not need to worried about the safety of lithium battery.
F: ADAS ( LDWS/FCW/FCMD ), the auxiliary warning system of driving, additional
considerate service of safety driving.
G: CPL filter is optional.
H: Real loop recording between two Micro SD cards, support 128GB high speed card.
I: One button mute video and one button protected video functions, use the Thumb-wheel
switch button to control Menu and Playback, convenient and elegance.
J: Electrostatic Film and 3M glue installation method are very intimate and safety. User
don’t need to worried about it will like the sucker installation method: block driver’s sight or
easy to drop off and hurt the driver.
More surprises, please study manual to find them.

4. SPECIFICATIONS
CMOS Sensor
SONY (1920*1080)
Chip
Ambarella A7
Display
1.5inch, 480x240
Format
Video:H.264 / Voice:ACC / File:MOV
Video Resolution
1920*1080 30P 16:9 / 1280*720 60P 16:9 / 1280*720 30P 16:9
HDMI
support
Micro SD card and
Formatting warning
Support dual cards, up to 128GB, support FAR32 and exfat
format, user can choose loop recording. If a card is use for a
long time in this camera and never be formatted, camera will
warning the user to format the card when it is turn on.
GPS track record
and playback
GPS Player is built-in the camera, support Baidu and Google
maps at the same time.
G-sensor collision
video protected
The current video will extend 15 seconds recording when
violence collision happened, this video will be auto-save and
locked. If the current video time is less than 10 seconds before
violence collision happened, the previous video will be locked
automatically. There are at most 20 files will be locked.
G-sensor data is not to be recorded.
Audio
Built-in microphone/ speaker
Loop recording and
segment
Segment time: 1min / 2min / 3min the card will remain
500MB space to make sure loop recording will not be
interrupted. If the protected files exceed 20 segments, the
earliest protected file will be unlocked automatically.
ADAS
LDWS (Land Departure Warning System)
FCW (Forward Collision Warning)
FCMD (Forward Car Motion Detection)
Recording time
after car engine
stop
If camera get power via car charger, it always save the video
and turn off immediately, no prolong video. If camera get
power from car battery via OBD II cable, default video is 10
seconds, user can set it in the MENU.
When violent
collision happened,
recording time in
parking guard mode
If camera get power from car battery via OBD II cable, default
recording time is 15 seconds when violent collision happened.
User can set it.
Maximum power
consumption
3W
Parking Guard mode
power consumption
1.5W
Standby current
12V <6mA
Battery
No battery inside, it’s super capacity

5. APPEARANCE
Remarks:
1. Thumb-wheel Switch
This button include three functions: UP / DOWN / OK
A. UP button: pull thumb-wheel switch upwards
1) When camera is standby, long press UP button for 2 seconds to enter the Menu, long
press UP button for 2 seconds again to exit the Menu.
2) In the Menu mode or Playback mode, short press UP button to choose the
sub-menu.
3) When camera is recording, short press UP button to control MIC on or off (mute
video). (see 6.6)
B. DOWN button: pull thumb-wheel switch downwards
1) When camera is standby or recording, long press DOWN button for 2 seconds to
enter the Playback.（see 6.9）

2) In the Menu mode or Playback mode, shore press DOWN button to choose
sub-menu.
C. OK button: push thumb-wheel switch middle
1) when camera is standby, short press OK button to start recording, short press again
to go back to standby.
2) When camera is standby or recording, long press OK button to take a photo.
3) In the Menu mode or Playback mode, short press OK button to confirm your choose.
2. SOS button
When camera is standby or recording, long press SOS button to control mute video.
(see 6.6)
When camera is recording, short press SOS button to protect the current video; short
press again to unprotected the video. (see 6.7)
3. Screen button
When camera is standby or recording, you can short press Screen button to turn off
the screen, short press again to turn on the screen.
Or you can set the power off screen time in the Menu. See 6.24
4. The other holes are cooling holes.
5. Camera Mounting Bracket
GPS logger and parking guard board are inside the camera mounting bracket.
3M sticker put here and then stick to car front window.
If no GPS and no parking guard function, it is a bracket only, but also can connect car
charger with micro USB port 2 to get power from car.

6. OPERATION
Read this chapter to know how to operate the camera.
6.1 Turn on /off camera
This camera not have battery inside, its supper capacity, so must connect with the power
when using it. (Power source see 7)
When connected with the power source, camera will automatically turn on. If no power
source, camera will automatically turn off.
When the camera is recording or standby, if user cut off the power suddenly, screen will
show red words ”do not power off”.
6.2 Recording Video & Take Photo
When the camera is standby, short press OK button to start video recording;
When the camera is recording, short press OK button to cancel video recording.
The camera is also pre-configured to auto start recording once it receives power, i.e. when
the car engine is started.
The camera is also pre-configured to auto stop recording and turn off once it loose power,
i.e. when the car engine is stopped.
Please notice short press SOS button to protect video when recording. see 6.7
When camera is standby or recording, long press OK button to take a photo.
6.3 Storage card preparation
The camera supports dual micro SD cards, both 64GB MAX.
The files can be stored in card A or card B. you can insert one micro SD card into the
camera or two micro SD cards into camera at the same time, provide more space to store
videos, images or other files. Please use high-speed micro SD card meeting the
specification of TFHC. (Class6 is perfect .Class10 may cause some problem because the
speed of card is too fast, it is better not use Class10 card)
6.4 Copy function for backup video
Video clips can be copied manually between cardA and card B, then you will have backup
after you hand over one card to police or the court.
1. Please choose card (see 6.9). For example, if you choose card A, then copy the files to
card B.
2. when camera is standby, long press DOWN button to enter playback video or photos
Then long press UP button to enter playback sub-menu, you can see COPY FILE TO
ANOTHER CARD, options are YES/NO.
3. If press OK button to choose YES, the selected video or photo will be copied from this
card to another card.
4. Please notice user can copy only one video or one photo to another card each time, not

all the files.
6.5 Loop recording
1. This camera supports automatic loop recording when the card is full. Here you can set
the segment length according to your requirement. If you need continuous video without
any segmentation, please set it to OFF but be aware that the maximum video file size is
4GB.
Video loop recording time setting see 6.21.
2. This camera also supports loop recording between card A and card B,Here you must
choose AUTO in choose card (MENU); if choose card A or card B, the videos will be not
loop recording between 2 cards, only one card is recording.
6.6 Recording Mute Video
When the camera is in either standby or recording, you can short press UP button to mute
the microphone inside camera any time; short press UP button again to cancel mute
status.
When the camera is in either standby or recording, you can long press SOS button to
mute the microphone inside camera any time; long press SOS button again to cancel
mute status.
6.7 SOS Manual Protect Video
The camera support automatic loop recording which means the oldest video will be
over-written by new video when the card is almost full unless the video is protected (read
only file attribute).
The camera can auto protect videos if the G-sensor data exceeds the configured
threshold.
You can also manually protect the videos by short press SOS button when recording;
short press SOS button again to cancel protected status.
If any impact is detected when recording, the current video will be locked automatically.
You can manually protect the video and picture in playback mode (see 6.9).
6.8 Power off Screen
When camera is standby or recording, you can short press SCREEN button to turn off the
screen to save power at any time, short press SCREEN button again to turn on the
screen.
Or you can set it in the MENU.
6.9 Videos and photos playback
1. Playback on camera
When the camera is in standby, long press DOWN button for 2 seconds to enter
videos playback; long press DOWN button again for 2 seconds to enter photos
playback; long press DOWN button thirdly for 2 seconds to standby.
When the camera is in standby, press UP and DOWN buttons to highlight the video or
photo you want to review, and then press OK to view.

When the camera is in playback, you can press UP or DOWN buttons to highlight the
video or photo you want to edit it, then long press UP button to active the sub-menu.
Press UP or DOWN buttons to choose and then OK button to perform the action.
Sub-menu:
1. FILE PROTECT OPERATION (protect current file / protect all files / unprotected
current file)
1. AUTO PLAY (video play one / video play all / video repeat one / video repeat all)
2. DELETE FILE (cancel / delete this file / delete all files), protected files can’t be
deleted here.
3. COPY FILE TOANOTHER CARD
4. CHOOSE CARD
If you want to playback videos/photos in cardA, please choose cardA; if you
want to playback videos/photos in card B, choose card B.
2. Playback on TV
When the camera is connected to a TV via an HDMI cable, the camera screen will be
turn off and the transfer the display to the TV. The operation will be the same as when
using playback on the camera.
For videos and photos playback only, can’t make any changes on the sub-menu.
(Please make sure camera connected with the power when playback on TV)
3. Playback on computer
When you wish to review the videos or photos on computer, a micro SD card reader
can be used, or you can connect the camera to your computer with the supplied USB
cable.
GPS PLAYER PROGRAM is placed in the PLAYER folder when a micro SD card is
formatted by the camera, which can playback the video recording with GPS traces.
You can also use a compatible media player to playback the MOV video files directly,
without the GPS trace.
If you connect the camera to your computer with the supplied USB cable. The camera
will be recognized as a mass storage device.
You can then use the camera as micro SD card readers for two separate micro SD
cards for playback.
6.10 Light Indicator
Blue blinking: the camera is in parking mode with low frame rate recording.
Red blinking with Blue: the camera is in normal recording mode with MIC on.
Red blinking: when in normal recording mode, MIC off;
When in parking mode, this means a shock triggered recording.
6.11 Red Light in Bracket
Car engine is started

6.12 Reset
If the camera can’t work or freeze, you can try to long press RESET button to reset it.
6.13 Resolution
Here you can choose the video resolution you want to use; higher resolution videos will
take more storage space.
Options: 1920*1080 30P 16:9 1280*720 60P 16:9 1280*720 30P 16:9
6.14 Quality
Here you can adjust the video quality; the quality will affect video grain, sharpness,
contrast and so on. Better quality videos will result in higher bit rate and take more storage
space.
Options: Normal / S.Fine (super fine) / Fine
6.15 AE Meter Mode
Here you can set the measuring area for Auto Exposure; this setting will affect the video
brightness and quality. CENTER is recommended if there is no special requirement.
Options: Center / Average / Spot
6.16 WDR
Options: ON / OFF
6.17 ADAS Detect / ADAS Calibration
ADAS: LDWS (Land Departure Warning System)
FCW (Forward Collision Warning)
FCMD (Forward Car Motion Detection)
Options: ON / OFF
6.18 Flicker
Here you can set the sensor flicker frequency to fit your AC power frequency and reduce
the effect of flickering lamps. Please leave itAUTO if you don’t know which frequency is in
use in your country.
Options:Auto / 60hz / 50hz
6.19 White Balance
Here you can set the image white balance mode to improve color balance in videos /
images in different weather and lighting conditions. Auto is recommended to fit most
conditions.
Options:Auto / Sunny / Cloudy / Tungsten / Fluorescent
6.20 Exposure Values (EV)
Here you can manually adjust the Exposure Values (EV) to improve the image brightness.
Options: 0 / +0.3 / +0.7 / +1.0 / +1.3 / +1.7 / +2.0 / -2.0 / -1.7 / -1.3 / -1.0 / -0.7 / -0.3

6.21 Recycle
This camera supports automatic loop recording when the card is full. Here you can set the
segment length according to your requirement. If you need continuous video without any
segmentation, please set it to OFF but be aware that the maximum video file size is 4GB
and the camera will stop recording once the card is full.
Options: 1 MIN / 3 MIN / 5 MIN / OFF
6.22 Motion Detect
Motion detection is used to reduce the amount of storage space used. When there isn’t
obvious motion detected the camera will switch standby. Once motion over the threshold
value is detected, the camera will start recording and continue until 15 seconds after the
motion stops.
Options: OFF / ON
6.23 Time Setup
Here you can set the Time Zone, system date and time manually. The date/time
information will be automatically updated if GPS satellites are connected.
00 2015 / 01 / 01 12:12
Time zone Date Time
The time zone, corrected for daylight saving time, will need to be set before the GPS
signal can correctly update the time.
6.24 Power off Screen
When camera is standby or recording, you can short press SCREEN button to turn off the
screen to save power at any time, short press SCREEN button again to turn on the
screen.
Or you can set it in the MENU, options are OFF / 10 sec / 20 sec / 30 sec.
6.25 Stamp
Here you can stamp information on video.
Options: OFF / Date Time / Driver Number Stamp
6.26 Drive Number
Here you can define the driver number or your customized information to stamp on the
video (9 characters or numbers).
6.27 GPS Stamp
The camera can record your driving track and stamp the GPS data on video.
Here you can define the GPS data stamping method. Please notice there maybe
electronic interference on GPS signal from camera, radar detector, wireless transmitter,
hardwire kit, car charger, or something else; which will delay the GPS connecting or
mistake the GPS data.An external GPS antenna will help to enhance the reliability.
Options: OFF / ON

6.28 Speed Stamp
Here you can set the Speed stamp.
Options: OFF / ON
6.29 G-sensor Sensitive
The G-sensor is used to detect the 3-axis impacting forces. If any impact over the
threshold value is detected. The current recording file will be locked / protected to avoid
being over-written. Here you can define the sensitivity threshold value.
Options: CLOSE / LOW / MIDDLE / HIGH
6.30 GPS (see 6.39)
Options: ON / OFF
6.31 Speed Unit
Options: Km/H / MpH
6.32 Parking Guard Mode (see 6.40)
Options: Low frame mode / normal mode / OFF / Pre-record mode
6.33 Senior Setting
6.34 Language
Here you can set the language you prefer.
Options: English / 简体中文 / 繁體中文 / Русский
6.35 Default Setting
Here you can restore all the settings to the factory default settings.
Default setting in Menu, options: NO / YES
6.36 Format
Before using, please format the cards in the camera or computer to avoid some
unnecessary troubles. Please check the card icon shown (card A or card B) on screen
carefully before formatting, all files will be lost once you start the formatting process.
After a period of time, We suggest users to format the cards regularly.
(If you are using micro SD card bigger than 32GB, please format the cards on a computer
to be FAT32 format)
Options: NO/YES
6.37 Choose Card
Here you can choose the card which you want to store the videos and photos.
Options: Auto / CARD A / CARD B
If there is only one card in camera body, this card will store videos and photos by default.
If there are two cards in camera body,
1. Here chooseAuto, loop recording between cardA and card B. Please make sure don’t

set Recycle OFF, otherwise once the recording card is full, the other card will not start
to record.
2. If choose CARD A or CARD B, only CARD A or CARD B store videos and photos, not
loop recording between two cards.
There is another choose card sub-menu in playback, not the same as here.
6.38 Firmware version
Here you can find the current version of the firmware in your camera.
You may need this information when you are trying to upgrade the camera to a later
firmware.
Firmware update process:
1. Copy firmware (bin) file into Micro SD card.
2. Insert Micro SD card into camera and turn on the power, please make sure camera
connect with the power in the process.
3. Waiting for several seconds, “firmware update? YES, NO”on the screen, choose YES
to update it, the camera will automatically to update the firmware, all the process will
takes about 1 minute.
6.39 GPS
GPS tracker
The camera can record your driving track and stamp the GPS data on video. You can
define the GPS data stamping method.
Options: OFF/ON
If you want to use GPS function, please make sure car charger connected with the micro
SD card slot in the GPS (micro USB port 2 in bracket), not the micro SD card slot 1 in the
camera body.
Please notice there maybe electronic interference on GPS signal from camera, radar
detector, wireless transmitter, hard wire kit, car charger, or something else; which will
delay the GPS connecting or mistake the GPS data, GPS signal will be very weak under
the bad weather.
GPS player
Before playing the GPS tracker, user need to download GPS player QTPLAYER
application into your computer, operations as below:
1. Insert your micro SD card into camera; the camera system will copy the GPS player to
your SD card automatically.
2. Connect your camera to computer, find [Player] file, double-click the to
start the player. At the same time, it will jump out a window as below, please choose
YES to download the Quicktime. You need install the driver (named Quicktime) before
using.
(You can also visit Quicktime website to download it directly:
http://www.apple.com/quicktime/download/)

Please click the red arrow words:
1. Previous Versions of QuickTime for Mac and Windows
2. QuickTime 7.7.6 for Windows
3. Download
3. After download, find the Quicktime driver , double-click
to install.
4. After installing the Quick time in your computer, now you can back to micro SD card
and use the GPS player now.

5. click to import files from camera, use or to check more
files.
Player Icon:
Open the video file form here
Remarks: If user uses to play the video directly, it will not have GPS track. So
we suggest user copy all PLAYER file from micro SD card to computer, and play the
videos on , by this way, all the GPS information will be showed.
6.40 Parking Guard
(OBD power supply and how to use parking guard function)
1) When using Parking Guard Function , only use OBD II cable to get power from car
battery.
use OBD II cable, plug and use, it is very easy and convenient (Optional).
Please notice that you can not use car charge at the moment , please remove the
Micro USB cable from GPS box bracket when using parking guard function.
2) In the OBD power supply mode, built-in CPU will auto-detect whether the car engine is
started.

if the car engine is detected,the camera will start recording.
3）if the car engine is stopped, the camera will be in Parking Guard modes, there are 4
modes in this status, user can choose one of them. (choose it in camera menu, the
default is A):
A:Normal mode: camera will not record after parking, but it will auto start to record a 15
seconds emergency video when unexpected shocks or collision is detected, And the
video file will be locked automatically.
(advantage:the Micro SD card’s life will be extended under this mode.)
B: Low Frame mode: When parking, camera will start loop recording in low
Fps status (1fps/second). Once unexpected shocks or collision is detected, camera will
auto start to record a normal fps 15 seconds emergency video immediately, and this video
file will be locked automatically. camera will go back to low fps recording if the crisis is
resolved.
(advantage: under this mode, the whole course will be recorded when parking).
Parking guard function with Time Lapse for monitor your car perfectly when parking
under low FPS monitor mode.
C: Pre-record mode:Once unexpected shock or collision is detected, the camera will save
and lock two videos, each videos last for 15 seconds, one is recording the video before
violence collision happened, the other one is recording the video after violence collision
happened.
(advantage: under this mode, Car owner know what happen before and after shock or
collision happened . One more is the Micro SD card’s life will be extended )
D: OFF: Don’t use this function at all . No any record after car engine is stop. (under this
mode, camera didn’t work all the time, and save the power of car battery. )
4)When the voltage of car battery below safe starting voltage, camera power will cut off
power automatically, enter the standby mode, under this mode, camera almost no need
power. User can set this safe voltage in the senior setting, default setting is 11.5V.
5)Parking Guard setting and other settings:
A: Firstly, use car charger to charge the camera, turn on it, long press UP key to enter
MENU, set Parking Guard mode, save and exit MENU.
B：Use OBD II cable connect camera with parking guard hole in GPS bracket. The camera
will automatically turn on once the card engine is started. Please press OK key to stop
recording, under standby mode,

6）Parking Guarding parameter setting as below：
Items
Functions
Default
Settings
Function Descriptions
1
Parking Guard Mode
Normal
Mode
As above
2
collision detection sensitivity w
hen the car engine was stop
Middle
3
recording times after violence
collision happened
15
seconds
4
recording times after car engin
e stop
15
seconds
5
collision detection sensitivity w
hen the car engine is starting
Middle
6
voltage of car battery when c
ar engine was started
13.3V
When the car engine is
started, automotive alternator
charge to car battery voltage is
13.3V. If the car battery
voltage more than 13.3V, it
means the car is start and
camera will be in recording
mode. Different cars, different
battery ageing situation, then
different voltages, 13.3V is the
most common voltage. In
Parking Guard mode, start the
car engine, if the camera can’t
recording, maybe this voltage
is a little higher than the actual
value; if the camera can’t stop
recording automatically after
car engine stop, maybe this
voltage is a little lower than the
actual value, need to make
adjustment.

7
the lowest voltage of car engi
ne starting
11.5v
If car battery voltage below
11.5V, camera can not get
power from OBD ,camera will
be turned off automatically,
Parking Guard function will not
work at the same time, to
ensure the car engine start will
work as normally.
7. POWER SOURCE
The camera can be powered by power lead for cigar lighter socket (standard accessory),
or OBD II cable (optional accessory).
1. Power lead for cigar lighter socket is a easy & fast connecting method for camera, the
only thing you need to do is plug the power lead into the cigar light socket in your car.
The camera will be powered once the engine is start. The advantage of power lead for
cigar lighter socket is it will engage your cigar lighter socket and maybe alignment
difficulty for the long cable.
2. Please connect the car battery with round hole in GPS (bracket) via OBD II cable.
When using parking guard function, camera must use OBD II to get power from car,
don’t use the car charger.
8. MOUNTING
The camera is designed for easy & quick mounting to your windshield with the VHB sticker
pad.
1st, mount the camera to the mounting bracket with power cable plugged into either the
mount or camera body;
2nd, simulate the unit on your windshield with the camera powered on, rotate the camera
vertically to find the best mounting location;

3rd, clean and dry your windshield, put the film on it. Stick the VHB sticker pad to the
mount bracket or wedges, and attach it in the film to your windshield, hold the mount for a
few seconds to ensure good adhesion;
4th, power on the camera and check the camera display again.
When you want to demount the camera, just slide the camera out from the mounting
bracket; no need to take the mounting bracket down.
If you want to change the location, just remove the film, take the camera and bracket
down, it is very convenient.
Please don’t break off the mount bracket from windshield with a rigid crowbar, which may
damage the mount bracket or your windshield.
The recommended mounting location for camera is at the center of the windshield, just
behind the rear view mirror. That is the most invisible location to hide the camera, and will
never interrupt you when driving.
9. PC SYSTEM REQUIREMENTS
Windows XP or later operating system, MAC 10.1
Intel Pentium 4 2.8Ghz CPU or above (recommended 3GHz)
At least 2GB RAM or above (recommended 4GB）
Internet connection (for GPS log playback)
10. UI ICON and STATEMENT