miseno MNO351CP User manual

SINGLE HANDLE KITCHEN FAUCET
Model MNO351CP, MNO351SS, MNO351ORB
1
CAUTION-TIPS FOR REMOVAL
OF OLD FAUCET:
Always turn off water supply
before removing existing faucet
or replacing any part of the
faucet. Open the faucet handle
to relieve water pressure and
ensure that water is completely
shut off.
CARE INSTRUCTIONS:
To preserve the finish of your
faucet, apply non-abrasive wax.
Any cleaners should be rinsed
off immediately. Do not use
abrasive cleaners on the faucet.
11/30/15 REV.A
You may need
Goggles Wrench Basin Wrench
(2) Supply Lines Sealant Tape Silicone
SILICONE
Phillips Head Screwdrivers

211/30/15 REV.A
3
2
1
4
1
3
2
1
4
3
2
1
3
4
2
Standard Installation
Shut off water supplies.
(If installing the faucet with the escutcheon, begin with step 2.)
Insert faucet body through the hole in sink. Install plastic washer
(1) and metal washer (2) onto the threaded mounting shank.
Thread nut (3) onto mounting shank. Lock nut into position by
tightening screws (4). Do not overtighten.
Please continue to Step 4.
Optional Escutcheon Installation
Shut off water supplies.
(If installing the faucet without the escutcheon, begin with step 1.)
Screw the bolts (1) into the escutcheon (2) and ensure that the
base plate (3) is pressed onto the escutcheon (2) before the
escutcheon (2) is installed over the three holes in the sink. From
underneath sink, hand tighten the mounting nuts (4). Do not
overtighten.
Note: If the sink surface is uneven or irregular, plumber’s putty or
a silicone sealant may be used to create a watertight seal.
Plumber’s putty may have an adverse reaction with plastic
gaskets under the spout base so if your faucet has a plastic
gasket, use a high quality silicone sealant. Plumber’s putty also
may have an adverse reaction with some cultured marble or
natural stone. In these cases a high quality silicone sealant is
recommended.
Optional Escutcheon Installation (2)
Insert faucet body through the hole in escutcheon.
Install plastic washer (1) and metal washer (2) onto the threaded
mounting shank. Thread nut (3) onto mounting shank. Lock nut
into position by tightening screws (4). Do not overtighten.

311/30/15 REV.A
4
3
2
1
4
4
Weight
here
Weight
here
5
2
1
6
Screw quick connector to the free end of hose.
Align block (1) and tabs on quick connect. Push quick connect housing
firmly upward and snap onto receiving block. Pull down moderately to
ensure connection has been made.
If it is necessary to remove quick connect, squeeze tabs on hose
between index finger and thumb, then pull down to disconnect.
Install the weight clip (2) at the point of the hose (3) marking “weight
here”. Insert the weight (4) onto the clip (2) by sliding it down onto the
clip (2).
Making the waterline connections
Thread the nut (1) on supply line onto outlet of water supply valve (2)
and tighten with wrench. Do not overtighten.
After installation is complete, remove the sprayer by unscrewing it in a
counter-clockwise direction.
Turn on the water supply to flush debris from the faucet. Run the hot and
cold water for at least one minute each.
Important: This flushes away any debris that could cause damage to
internal parts.

4
* Specify Finish
Maintenance:
If faucet leaks underneath handle or water does not completely shut o: Replace
cartridge.
11/30/15 REV.A
RP70550
Bonnet
RP70421
Block
RP60002
O-ring
MIR20052
Cartridge
RP80237*
Cap
RP50095
Screw
RP13454*
Handle
RP50002
Set Screw
MIRXC3811901
Sprayhead
RP50137
Bolt
RP56109
Mounting Nut
RP80536*
Escutcheon
RP50004
Screw
RP64131
Plastic Washer
RP64111
Metal Washer
RP60089
O-ring
RP70479
Quick Connector
RP56077
Nut
RP70551
Hose
RP60071
O-ring
RP70380
Wearable ring
RP64204
Weight Clip
RP70525
Weight