Mitsumi CR series User manual

MITSUMI
CR Series CD-R/RW
Drives
INSTALLATION MANUAL
VERSION 5.1

Mitsumi Internal CD-ReWritable Quick Installation Guide
1. Start by shutting down the computer along with the monitor and any other
peripherals.
2.Unplugthepowercordfromthecomputer.
3.Removethecomputercasecover.
4.Removethecoverfromanemptydrivebay.
5. Attach mounting rails or brackets to the drive if required.
6. Note the pairs of pins on the back of the drive labeled: Master, Slave and
CableSelect.
7. Note that one of the pairs has a small jumper between them. The factory
setting for the jumper is Master. If necessary, move the jumper to Slave if the
drivewill share an IDE data cable withanotherdrive.
8. Slide the drive into the chassis and secure with the mounting screws.
9. Align the connector of the 40-pin IDE cable with the pin slot on the drive
noting the position of pin 1 and the notch on the connector itself. Gently press
the connector into the pin slot making sure it seats completely and firmly.
10. Plug the other end of the IDE cable into the IDE Secondary connector
locatedon the motherboard.
11. Attach an unused power cable to the back of the drive, with the beveled
edgeup.
12. Plug the audio cable into the audio-out connection on the back of the drive
as shown. It should set firmly with a locking tab securing it. Next, connect the
otherendintoan available audio-in connection on the sound card.
13.Replacethecomputercasecover.
14.Plugin the power cord, connect other computer peripheralsandturn on
yourcomputer.
15. As the computer turns back on, the WindowsTM operating system will
automaticallyrecognizethenewdriveandwillmakeit available for use.
16.InserttheSoftwareInstallationCDandfollowtheon-screen instructions for
installingthewriting software.

PowerCable
40-pinInterfaceCable
AudioCable
Pin #1
Rear View of the Drive
Power Cable - Supplies power to the CD-R drive from a standard
PC AT power supply.
40-pin Interface Cable - Connection for 40-pin ribbon IDE
interface cable.
Audio Cable - Provides stereo audio output to a sound card.
CAUTION:Thedischargeofstatic elctricity can damage electronic
circuitry. Avoid static discharge by touching a grounded metal object such
asthecomputercasebeforeandduringinstallationofyournewdriveor
bywearingagroundingstrapconnectedtoagroundsource.

Mitsumi External CD-ReWritable Quick Installation Guide
1. Using an audio cable, connect your drive to your speakers.
2. Next, connect the power cable and plug into a power source.
3.Turn the power of the External CD-R/RWDriveon.
4. Connect the USB cable to the PC.
5. The PC will automatically detect the External CD-R/RW Drive. Click “Next>”.
6.Check“Search for the best driver for your device”andclick “Next>”.
7.Check “Floppy disk drives”. Inset the diskette provided with theExternal CD-
R/RW Drive into the A:\ drive and click “Next>”.
8. Click “Next>”.
9.The device driver willbeinstalledfor your External CD-R/RWDrive.

PowerCable
AudioOut
Power Switch
Rear View of the Drive
USB Connector
Power Cable - Supplies power to the external CD-R/RW drive .
USB Connector - Connection for USB interface cable.
Audio Out - Provides stereo audio output to a speaker.
Power Switch - Power on/off

Safety Information
Please follow all safety warnings and instructions printed in this manual and on
theCD-R/RW drivetoavoid damagingyourdriveor harmingyourself.
Neverattempt to servicethedriveyourself.
Nouserserviceableparts are inside the unit.
Openingor removingthecover canexpose
youto dangerous voltage levels, laser beams,
andother hazards.
Do not attempt to open the unit. The laser beam
usedbythe CD-R/RW drive can be harmful to the
eyes. Allservice procedures should be per-
formedby an authorized dealer or distributor.
Note that the noise level of compact disc audio is much lower than that of an
analog audio source. Do not attempt to set the speaker sound level by listen-
ing to the noise level. Too high a setting can damage your speakers. Begin
withthesound level set low, then gradually increase the volumetothe desired
level.
Disclaimer
The vendor shall have no liability or responsibility to the purchaser or any other
person for any loss or damage or any special, incidental or consequential
damages caused or alleged to be caused directly or indirectly by the product,
including, but not limited to, loss of previously or currently written data, any
interruption of service, loss of customer goodwill, loss of business, anticipatory
profitsorconsequentialdamagesresultingfromtheuseoroperationofthe
product.

Federal Communications Commission (FCC)
Information
This unit generates and uses radio frequency energy and if it is not installed
and used properly in strict accordance with the manufacturer’s instructions, it
maycauseinterferencewithradioandtelevisionreception.Thisunithasbeen
tested and found to comply with the limits for a class B computing device, in
accordance with the specifications in Part 15 of the FCC rules which are
designedto provide reasonable protection againstsuchinterferenceina
residentialinstallation.
Wecannotguarantee,however,thatinterferencewillnotoccurinaparticular
installation.Ifthisunit does cause interference to radio or television reception,
which can be determined by turning the unit off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorientthereceivingantenna
• Relocate the unit with respect to the receiver
• Movethe unit awayfromthereceiver
• Plug the unit into a different outlet so that the unit and the receiver
areon different branch circuits
Ifnecessary,consult your dealer oranexperiencedradio/television engineer for
additionalsuggestions. The booklet“Howto Identify andResolveRadio-TV
InterferenceProblems,” Stock No.004-000-00345-4,maybe helpful. This
bookletwaspreparedbytheFederalCommunicationsCommissionand is
availablefrom the U.S.GovernmentPrintingOffice, Washington, DC20402.
Changesor modifications not expresslyapprovedbythe manufacturer for
compliancecouldvoidtheuser’s authority to operate the equipment.

For customers in Canada
ThisClassBdigital apparatus meets all requirements of the Canadian Interfer-
ence-CausingEquipmentRegulations.
Pour les utilisateurs au Canada
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglementsur le matériel brouilleurduCanada.
FCC Declaration of Conformity
MITSUMI CR-4802TE
CR-4802TU
CR-4803TE
CR-4804TE
The device complies with part 15 of the FCC (U.S.A.) rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference,and (2) this device must accept any interferencereceived,includ-
inginterferencethat may cause undesired operation.
MITSUMIElectronics Corp.
5808W.CampusCircle Dr.
Irving,TX.75063
Tel.[phone]

CR-4802TE Specifications
SupportedDiscFormats
CD-ROM Mode 1; CD-DA; CD-i; Video CD; CD-Extra (CD Plus)
CD-ROM XA Mode 2 Form 1 and Form 2; Photo CD
WritingMethods Disc-at-Once,Track-at-Once,Multisession,
Packet Writing
DiscDiameters 12 cm, 8 cm
Interface ATAPIspecificationSFF-8020i/8080
DataTransferRate(Average)
Read: 1200Kbytes/sec (Mode 1), 1400 Kbytes/sec (Mode 2)
Write: 600 Kbytes/sec (Mode 1), 700 Kbytes/sec (Mode 2)
IDEData TransferRate(Burst)
11.1 Mbytes/sec (16 bits PIO mode)
13.3Mbytes/sec(MultiwordDMAmode)
AverageAccess Speeds (including the latency time)
Random 150 ms typical
Full Stroke 250 ms typical
DataBuffer Size2 Mbyte
Audio
Channels 2channels
Sampling Frequency 44.1 kHz
Filtering 4 times over-sampling, digital/analog filters
Quantization 1 bit (16bits linear equivalent)
Volume Control Software, L& R separate volume control
Reliability(MTBF)
Power on hour 50,000hours
DimensionsandWeight
Width/Height/Depth 148 x 42 x 210 mm
Weight 0.9 kgW max.
PowerSupply
DC +5V +5V +/-5%, 2.00A max. @ 8x full stroke
DC +12V +12V +/-5%, 2.80A max. @ 8x full stroke
EnvironmentalConditions
Operating: 5~40°C, 20 to 85% RH non-condensing
Storage: -20~60°C, 10 to 95% RH non-condensing

CR-4802TU Specifications
SupportedDiscFormats
CD-ROM Mode 1 and 2; CD-DA; CD-i; Video CD; CD-Extra (CD Plus)
CD-ROM XA Mode 2 Form 1 and Form 2; Photo CD (read), CD UDF
WritingMethods Disc-at-Once,Track-at-Once,Multisession,
Packet Writing
DiscDiameters 12 cm, 8 cm
Interface USBInterface
DataTransferRate(Maximum)
Read: 1200KB/s (8X speed)
Write: 600 KB/s (4X speed)
Rewrite: 300 KB/s (2X speed)
AverageAccess Speed
Random 200mstypical(8Xspeed)
DataBuffer Size2 MB
Audio
Channels 2 channels
Sampling Frequency 44.1 kHz
Filtering 4 times over-sampling, digital/analog filters
Quantization 1 bit (16bits linear equivalent)
Volume Control Software, L& R separate volume control
LoadingMechanism
Power tray
InstallationOrientation
Horizontal
Lifetime(MTBF)
50,000 POH
ExternalDimensions
7.6” wide x 2.1” high x 9.9” deep [194 (W)x 53.5 (H) x 255.70 (D) mm]
Weight
5.01 lbs. [2.27kg]
PowerSupply
AC110-240V(50Hz-60Hz)
EnvironmentalConditions
Operating: 5~40°C, 20 to 85% RH non-condensing
Storage: -20~60°C, 10 to 95% RH non-condensing

CR-4803TE Specifications
Supporteddisc formats
CD-ROM Mode 1; CD-DA; CD-i; Video CD; CD-Extra (CD plus)
CD-ROM XA Mode 2 Form 1 and Form 2; Photo CD
WritingMethods Disc-at-Once,Track-at-Once,Multisession,
Packet Writing
Discdiameters 12 cm, 8 cm
Interface ATAPIspecificationSFF-8020i/8080
Datatransfer rate
Read:(MAX) 3000 Kbytes/sec (Mode 1), 3500 Kbytes/sec (Mode 2)
Write:(average) 600 Kbytes/sec (Mode 1), 700 Kbytes/sec (Mode 2)
(Compatible only with 2x speed recording for CD-RW disc)
IDEData transfer rate (Burst) 16.6 Mbytes/sec (16 bits PIO mode)
16.6Mbytes/sec(MultiwordDMAmode)
Average Access speeds (including the latency time)
Random 135 ms typical
Full Stroke 220 ms typical
DataBuffer Size 2 Mbyte
Audio
Channels 2 channels
Sampling Frequency 44.1 kHz
Filtering 8 times over-sampling, digital/analog filters
Quantization 1 bit
Volume Control Software, L& R separate volume control
Reliability(MTBF)
Power on hour 50,000 hours
Dimensionsand weight
Width/Height/Depth 148 x 42 x 210 mm
Weight 0.9 kgW max.
PowerSupply
DC +5V +5V +/-5%, 2.00A max. @ 20x full stroke
DC +12V +12V +/-5%, 2.90A max. @ 20x full stroke
Environmentalconditions
Operating 5~40°C, 20 to 85%RH non-condensing
Storage: -20~60°C, 10 to 95%RH non-condensing

CR-4804TE Specifications
Supporteddisc formats
CD-ROM Mode 1; CD-DA; CD-i; Video CD; CD-Extra (CD plus)
CD-ROM XA Mode 2 Form 1 and Form 2; Photo CD
WritingMethods Disc-at-Once,Track-at-Once,Multisession,
Packet Writing
Discdiameters 12 cm, 8 cm
Interface ATAPIspecificationSFF-8020i/8080
Datatransfer rate
Read:(MAX) 3600 Kbytes/sec (Mode 1), 4200 Kbytes/sec (Mode 2)
Write:(average) 600 Kbytes/sec (Mode 1), 700 Kbytes/sec (Mode 2)
IDEData transfer rate (Burst) 16.6 Mbytes/sec (16 bits PIO mode)
16.6Mbytes/sec(MultiwordDMAmode)
Average Access speeds (including the latency time)
Random 135 ms typical
Full Stroke 220 ms typical
DataBuffer Size 2 Mbyte
Audio
Channels 2 channels
Sampling Frequency 44.1 kHz
Filtering 8 times over-sampling, digital/analog filters
Quantization 1 bit
Volume Control Software, L& R separate volume control
Reliability(MTBF)
Power on hour 50,000 hours
Dimensionsand weight
Width/Height/Depth 148 x 42 x 210 mm
Weight 0.9 kgW max.
PowerSupply
DC +5V +5V +/-5%, 2.00A max. @ 20x full stroke
DC +12V +12V +/-5%, 2.90A max. @ 20x full stroke
Environmentalconditions
Operating 5~40°C, 20 to 85%RH non-condensing
Storage: -20~60°C, 10 to 95%RH non-condensing

Licenses and Trademarks: Product names mentioned in this manual are trademarks or
registered trademarks of their respective companies and are hereby acknowledged. Informa-
tion in this manual is subject to change without notice and does not represent a commitment on
thepartofthe vendor. Thesoftware describedin thismanual isfurnished undera licenseagree-
ment and may be used or copied only in accordance with the terms of that agreement.
Printed in USA. June, 1999