Mobvoi AI Recorder User manual

Manual

Package contents
Mobvoi AI Recorder
USB Type - C data wire
Quick guide
Manual

Device composition
Dual microphone
array (high-
sensitivity
digital silicon
microphone)
Front side of AI recorder
Rear side of AI recorder
Record key
On/WiFi fast
transfer key
Magnetic back clip
USB-C

Operation instructions
1. Power on, start button is on in green, APP will
detect device Bluetooth automatically for connection.
2. If device has been connected to mobile phone
Bluetooth, the device will have automatic connection
when detect that Bluetooth is enabled.
Bluetooth pairing
Long press Bluetooth until green indicator flickers

1. Power on, click “Record” and it will shake;
recording is started when red indicator flickers.
2. Click “Record” key again to shake, red indicator
is off and recording is stopped.
Start/stop recording

WiFi fast transfer
1. When Bluetooth is connected to mobile phone, click
WiFi button again, WiFi blue indicator is on, which
means WiFi fast transfer is enabled.
2. The APP will detect WiFi automatically for
automatic connection.
3. When APP is connected, enter the device’s folder
for data synchronization.
Turn on WiFi fast transfer to speed up transfer of
record into mobile phone APP

Indicator status
Recording is
completed
Bluetooth
connection
Recording in
process
Wait for Bluetooth
connection
Low power
Power on
Power off
WiFi connecting
WiFi connection
enabled
WiFi connected
OTA upgrading
Charging
Charging
completes
Record key
Red indicator is
off
Green indicator
is normally on
Red indicator
flickers
Green indicator
flickers
Green indicator
is on
Red indicator
is on and then
becomes off
Red indicator
flickers
Blue indicator is
normally on
Yellow indicator
flickers
Red light is
on
Green indicator
is normally on
Blue indicator is
on
Blue indicator
flickers
WiFi on/off
key
WiFi on/off
key (charging)

Connect new device
Open mobile phone APP → Bluetooth setting,
click “Unbind device” to connect the recorder to
new mobile phone. The mobile phone can also be
connected to new device.
Operation instructions
v 1.6.2
123 h
Firmware version
Space management
Unbind device

Safety and precautions
Safety and Notice
Important safety message
Please handle the recorder with care to avoid
damage, battery liquid leakage, overheat, fire,
explosion or personal injuries if it falls down, burns,
be pierced, squeezed, dismantled or exposed to high
temperature or liquid, for it contains high-sensitivity
electronic components (including battery). Do not use
if the recorder is damaged.
word mark and trademark are owned
by Bluetooth SIG, INC. Use of this mark by Shenzhen
Tinno Technology Co. Ltd. is subject to the license.
Other trademarks and trade names are owned by the
respective owners.
Battery
Do not attempt to replace the recorder’s battery
to avoid damage, overheat or personal injury.
The battery must be operated by manufacturer or
maintenance institute authorized by manufacturer.
[Warning] Do not put the recorder in high-
temperature environment, such as places with
direct sunlight, open fire, heating, microwave oven
and oven. Do not put the recorder in water to avoid
battery overheat.
USB connection wire and recorder
Avoid long-term contact between skin and plug when
USB connection wire is connected to power supply;
otherwise, discomfort or injury will occur. For example,
do not sit or lean on the USB plug, nor put under the
carpet, pillow or your body when connection line is

inserted into power socket for charging. Please be
careful if your perception of heat is affected.
Please charge the recorder using the charger
permitted by manufacturer; otherwise, fire hazard,
explosion or scald will occur. Do not touch any
exposed metal of USB connection wire when
connecting power supply to avoid electric shock.
Make sure USB connection wire and recorder are
put in dry places during charging, and make sure
USB connection wire and recorder are not immersed
in water; otherwise, electric shock or short circuit
will occur and further lead to fire hazards, explosion
and scald. Stop using the recorder immediately if it
becomes hot; if the recorder becomes hot during
charging, unplug the recorder and USB connection
line from power supply, contact the manufacturer’s
after-sales personnel for solutions, in order to avoid
scald or battery explosion.
Suffocation
Do not swallow or bite the recorder, but keep it
inaccessible to children for it may lead to suffocation
or other injuries of children.
Electronic device
Do not use the recorder where electronic device is
prohibited, for its radio wave may bring interference to
other devices and lead to accidents and hazards. Do
not use the recorder when you take a plane but follow
the regulations of airline, for it may affect the flight
system.
Interference of medical device
The electromagnetic wave may be emitted by
some components and radio of the recorder.
Besides, the recorder also contains magnets. Such
electromagnetic waves and magnets may bring
interference to the pacemaker, defibrillator or other
medical devices. Please follow the rules and turn off

the recorder in medical places where the recorder
is prohibited, or keep safe distance between your
recorder and the specific medical device. Please
consult your physician and manufacturer of medical
device to acquire the operation information of specific
medical device if using the recorder along with the
medical device. Please stop using the recorder
immediately if it is suspected to affect your heart rate
regulator, defibrillator or other medical devices.
Skin stimulation
Please stop using the recorder immediately if
there’s skin simulation when using the recorder. If
skin simulation remains, it is suggested that you see
a doctor and consult the professional doctor.
Electrostatic shock
Your body may encounter weak electrostatic
discharge when using the recorder in places with dry
area due to easy accumulation of static electricity.
Please avoid using the recorder in extremely-dry
places, or put the recorder onto the grounded and
unpainted metal object to minimize the hazard of
electrostatic discharge.
Ambient environment
It is recommended to use the recorder at temperature
[-5℃ -40℃ ] and store it at temperature [0℃ -30℃ ];
Otherwise, the recorder may be damaged. Do not
use the recorder in case of thunderstorm to avoid
possible damages. Do not use the recorder in humid,
rainy, dusty or oily places to avoid faults of internal
circuits. Do not use or store the recorder in places
which are close to gas station, inflammables or
explosives. Do not immerse the recorder in liquid or
expose it to pressurized fluid, such as water flow in
shower. Do not carry the recorder when you have
other activities, such as shower or swimming, to
avoid damaging it. The charging port can be corroded

by the sweat or liquid in charging USB. Make sure to
clean the charging USB before you put the charging
wire in the packaging box.
Certification Information
FCC ID:2AX5U-CXR-TNT

Hazardous Substances of
Product
Name and content of hazardous substances in
product
Part Name
Hazardous Substances
Polybromi-
nated Diph-
enyl Ethers
(PBDE)
Polybromi-
nated
Biphenyls
(PBB)
Hexavalent
Chromium
(Cr(Vl))
Lead (Pb) Mercury
(Hg)
Cadmium
(Cd)
Compone-
nts of
printed
circuit
board
The figure in this mark means the product enjoys
10-year environmental-protection period under the
normal use conditions.
The parts above may be excluded in the product due
to the difference of model. The actual configuration of
product sold should prevail.
Some internal/external components may have mark of
environmental protection period according to standard of China’s
electronic industry SJ/T 11364 and relevant laws and regulations
of China. The mark of use period on product and component may
vary depending on the component and manufacturer. For any
conflict or difference of environmental-protection period, the ones
on component should prevail.
Plastic
Metal
Battery
Accessory
This sheet is prepared as per SJ/11364.
：Content of hazardous substance of this part in all homogen-
eous materials is conforming to the limit requirements of GB/T
26572.
： Content of hazardous substance of this part in all homogen-
eous materials is nonconforming to the limit requirements of GB/T
26572.

Three-guarantee Voucher of
Mobvoi AI Recorder
Warranty Service
For any non-artificial performance failure of the
recorder under normal use condition, the consumer
of Mobvoi AI Recorder enjoys three-guarantee
services as of the date of procurement.
1. For any performance failure within 7 days after
procurement, the consumer may return, exchange or
repair the recorder.
2. For any performance failure within 15 days after
procurement, the consumer may exchange or repair
the recorder.
3. The recorder enjoys 1-year quality warranty as of
the date of procurement.
Three-guarantee service applies if:
The recorder is not dismantled, repaired, maintained
or modified without permission;
The recorder is not running in abnormal environment
(such as special environment with high magnetic
fields, strong electric field or high humidity);
The recorder is damaged due to violation against the
user’s manual;
The recorder has collision, falling and bending due to
improper storage, or faults and major deformations
due to liquid leakage in humid places.
The consumer should show the valid invoices and
three-guarantee voucher to enjoy the 3-guarantee
policies.
Three-guarantee service does not apply and
paid repairing is provided if:
1. The recorder is damaged due to improper use,
maintenance and storage of consumer;
2. The recorder is damaged due to unauthorized
dismantling;
3. The consumer fails to show the three-guarantee
voucher and valid invoice;

4. The model of product on three-guarantee voucher
is inconsistent or modified;
5. The recorder is damaged by Force Majeure.
After-sales service does not apply in the
following cases and the recorder has no quality
problems:
The customer is unsatisfied with the recorder’s
performance;
The customer is unsatisfied with the battery life,
compatibility, color, appearance and shape of the
recorder’s battery;
The recorder has normal wear and aging;
The attached charging wire is damaged and its color
and material have decay.

Sales Records
Customer Name:
Seller (seal):
Tel:
Address and Postcode:
SN No:
Address and Postcode:
E-mail:
Tel:
Procurement Date:

FCC regulatory conformance ：
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. owever, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
RF Exposure
The SAR limit of FCC is 1.6W/Kg for body. The highest SAR value reported under this
standard during product certification when used against the body is 0.243W/Kg.
Use 0mm away from the body.