MSTR BRAND RACK SK-SWING User manual

INSTRUCTION MANUAL
V1
Swing Arm Wall Mount Accessory for RACK SK14,SK28 and SK38
RACK SK-SWING

2
Required Tools
13mm
(1/2 in.)
5.5mm
(7/32 in.)
10mm
(3/8 in.)

3
Supplied Parts
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your
dealer; contact Customer Service. Never use damaged parts!
[01] x 2
[02] x 8 [03] x 8 [04] x 8
5/16 x 3½ in.
[05] x 4 [08] x 2
[07] x 4
[06] x 1

4
guration best
suits your needs. Attach the rack arm
of both swing arms [01] to the back
brace of the rack using carriage bolts
[02], washers [03], and lock nuts [04].
The swing arms [01] can be mounted
guration or a right
guration.
Attach Swing Arm to Rack Assembly
Left Hinge Right Hinge
[01]
[01]
[02]
[03]
[04]
[01]
[01]

5
12
Locate studs. Verify the center of the stud with an
nder.
CAUTION: Avoid potential personal injuries
and property damage!
ÙAny material covering the wall must not
exceed 16 mm (5/8 in.).
ÙMinimum wood stud size: common 2 x 4 in
(nominal 1½ x 3½ in).
rst lag
bolts on the center line of the stud
564 mm
41 cm
(16 in.)
Mounting to Wall (Wood stud)
(22.2in)
 

6
3 4 Start hinge side lag bolts [05]. Leave
approximately 13 mm (1/2 in.) of
space from the bolt head to the wall.
Drill pilot holes as illustrated.
CAUTION: Improper use
could reduce the holding power
of the lag bolt. To avoid potential
injuries or property damage:
pilot holes MUST be drilled to a
depth of 89 mm (3½ in.), using a
5.5 mm (7/32 in.) diameter drill
bit.
89 mm
(3in.)
5.5 mm
(7/32 in.)
[05]
[05]
13mm
(1/2 in.)
13 mm
(1/2 in.)

7
5Hang swing arm/rack assembly onto the lag
bolts [05].
[01]
[01]
[05]
[05]

8
7Tighten lag bolts [05] only until the washers [06]
rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
13mm
(1/2 in.
)
[05]
[05]

9
89Tighten lag bolts [05] only until the washers [07]
rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
13mm
(1/2 in.)
Drill through the top slots of the wall arms [01]
into the center of the next stud.
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage: pilot holes MUST be
drilled to a depth of 89 mm (3½ in.), using a 5.5
mm (7/32 in.) diameter drill bit.
89 mm
(3½ in.)
[01]
[01]
5.5 mm
(7/32 in.)
[01]
[01] [05]

10
12
406.6 mm
(16 in.)
Mark the locations for the lag bolts on the
corners of a rectangle measuring 406.4 (16 in.)
Drill pilot holes as illustrated.
CAUTION: To avoid potential injuries or
property damage:
ÙPilot holes MUST be drilled to adepth of 89 mm
(3½ in.) using a 10 mm (3/8 in.) diameter drill bit.
ÙNever drill into the mortar between blocks.
ÙMinimum solid concrete thickness: 8 in.
ÙMinimum concrete block size: 8 x 8 x 16 in.
89 mm
(3½ in.)
10 mm
(3/8 in.)
Mount to Wall (solid concrete or concrete block)
 
(22.2in)
564 mm

11
3 4
Insert lag bolt anchors [08].
CAUTION: To avoid potential injuries or
property damage be sure the anchors [08] seat
ush with the concrete surface.
[08]
Start hinge side lag bolts [05].
NOTE: Leave approximately 13 mm
(1/2 in.) of space from the bolt head
to the wall.
13mm
(1/2 in.)
13 mm
(1/2 in.)
[05]
[05]
[05]

12
5Hang swing arm/rack assembly onto the lag
bolts [05].
[01]
[01]
[05]
[05]

13
Tighten lag bolts [05] only until the washers [06]
rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
6
13mm
(1/2 in.)
[05]
[01]
[01]

14
8Tighten lag bolts [05] only until the washers [07]
rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
13mm
(1/2 in.
[01]
[01]
)
[05]

15
1 2
Close the rack arm/frame assembly onto the
swing arm. Secure frame arm to wall
arm with locking pins [08].
NOTE: Remove the locking
pins [08] and swing rack
away from the wall to
access the back of the rack.
[08]
[08]
Lock Frame to Wall
[08]

16
Run cables through both slots
on the wall arms [01] or out
the side of the rack frame to
prevent damage to the cables.
If there are additional cables
above or below that need to be
routed behind the rack, route
them through the slots of the
wall arms.
Manage Cables