Myenergi zappi Pedestal User manual

Pioneer Business Park, Faraday Way, Stallingborough, DN41 8FF | 03 33300 1303 | www.myenergi.com
myenergi Ltd. | Registration No. 10261262 June 2022, Revision 1.2
D3470
zappi
Pedestal
Installation Guide

Pioneer Business Park, Faraday Way, Stallingborough, DN41 8FF | 03 33300 1303 | www.myenergi.com
myenergi Ltd. | Registration No. 10261262 June 2022, Revision 1.2
D3470
1. Product Overview
The zappi Pedestal is designed for mounting the zappi EV charger. It can
accommodate either a single zappi or two zappismounted back to back.
2. Purpose of this document
These installation instructions contain the information required to ensure correct and
safe installation. These instructions should be read fully and understood before you
begin installation and should be retained for the lifetime of the product.
3. Warranty and Liability
myenergi shall not assume liability for defects or damage that are the result of failing
to follow the installation instructions. The liability exclusion particularly applies for:
bInstallation by untrained personnel
bImproper use
bRepairs not carried out by myenergi
bUse of non-genuine parts
4. Safety
4.1 Intended use
This stand is intended for the mounting of the myenergi zappi EV Charger(s) in a free
space, independent of wall mounting. It should not be used to mount anything other
than the myenergi zappi EV Charger(s). One pedestal can mount up to two zappi
chargers, one on either side.
4.2 Qualifications of installation personnel
These installation instructions are intended for suitably qualified installation
personnel only.
4.3 General safety information
The pedestal for the myenergi zappi EV Charger(s) has been developed, produced,
tested and documented according to the relevant safety and environmental
requirements and regulations.
For electrical safety information refer to the zappi EV Charger specific instructions.
Ensure only persons who have read these instructions have access to the
pedestal.

Pioneer Business Park, Faraday Way, Stallingborough, DN41 8FF | 03 33300 1303 | www.myenergi.com
myenergi Ltd. | Registration No. 10261262 June 2022, Revision 1.2
D3470
5. Box contents
b1nr zappi Pedestal
b6nr M6 x 25 Button Head Socket Screws (3nr per side – Come as part of
pedestal)
b2nr grommets (1nr per side)
b1nr Installation Guide
6. Appearance
7. Installation
Observe the safety information provided in section 4. In addition to these installation
instructions follow and comply with the local regulations relating to operation,
installation and environmental protection. Install the pedestal only in combination
with the application of the Operating and Installation instructions of the myenergi
zappi Pedestal
7.1 Required tools / Materials
Tool
Description

Pioneer Business Park, Faraday Way, Stallingborough, DN41 8FF | 03 33300 1303 | www.myenergi.com
myenergi Ltd. | Registration No. 10261262 June 2022, Revision 1.2
D3470
Suitable 10mm Fixings (To be
determined by installer based on
substrate depth etc.)
For fixing base plate to concrete
substrate.
4mm Allen Key/Hex Key
For mounting of the
zappi
EV charging
station.
Cabling tools
For making all connections
General tools, drill etc.
For mounting of the pedestal.
7.2Location requirements
bIf pedestal is installed in close proximity of a road or public parking place an
adequate collision barrier/guard/protector must be installed.
bShould you install more than one pedestal in the same location you should
ensure there is at least a 200mm gap between the two.
bThe surface you are mounting to should be fully level and flat.
7.3Mounting base
It is the responsibility of the installer to ensure the base for mounting the stand is of
a suitable build up and thickness and the fixings used to secure the pedestal are
adequate enough for the substrate you are mounting to.
General;
bThe electrical supply cables must come out of the concrete at the centre of the
pedestal’s baseplate and have an excess of at least 1500mm
7.4Step by step instructions
These instructions are for the installation of the pedestal only and should be read in
conjunction with the zappi operation and installation manual.
Step 1: Remove from box and recycle packaging.
Step 2: Remove rubber grommet as necessary on side you will be mounting your
zappi(s) and slice down the centre line to create an opening.
Step 3: Feed cable through the base plate and up the pedestal to the hole and through
the grommet.

Pioneer Business Park, Faraday Way, Stallingborough, DN41 8FF | 03 33300 1303 | www.myenergi.com
myenergi Ltd. | Registration No. 10261262 June 2022, Revision 1.2
D3470
Step 4: Fix base plate of pedestal down to substrate using fixings suitable for
thickness and material, as necessary.
Step 5: Remove screws from head of pedestal and keep safe for later use.
Step 6: Refer to mounting instructions in “zappi Operation and Installation Manual”.
Note: Use screws supplied with pedestal. Use washers supplied with zappi charger.
Step 7: Make electrical connection as per instructions in “zappi Operation and
Installation Manual”.

Pioneer Business Park, Faraday Way, Stallingborough, DN41 8FF | 03 33300 1303 | www.myenergi.com
myenergi Ltd. | Registration No. 10261262 June 2022, Revision 1.2
D3470
8. Maintenance, cleaning and repair
8.1 Maintenance
The pedestal does not require any maintenance.
8.2 Cleaning
bClean the installation only with a dry cloth. Do not use aggressive cleaning
agents, wax or solvents.
8.3 Repair
Unauthorised repair of this pedestal is not permitted.
9. Decommissioning the pedestal
In case the pedestal is to be decommissioned it should be carried out by an authorised
electrician.
bDecommission the charging station(s) in accordance with the “zappi
Operation and Installation Manual”.
bDismantle the pedestal.
bDispose of the pedestal in accordance with the national regulations.
10. Disposal
bDispose of packaging in corresponding recycling container and in accordance
with national regulations.
DANGER
High voltages – Danger of fatal electric shock
Never clean the pedestal with a high-pressure cleaner or similar device.
NOTE
bDo not use alkaline cleaning agents. Alkaline cleaning agents can cause a
discolouring of the pedestal.
b
Tree resin could also cause discolouration.

Pioneer Business Park, Faraday Way, Stallingborough, DN41 8FF | 03 33300 1303 | www.myenergi.com
myenergi Ltd. | Registration No. 10261262 June 2022, Revision 1.2
D3470
11. Technical Data
Specification
Details
Weight (kg)
8.3kg
Material
Aluminium
Corrosion Protection
Powder coated
Colour
RAL 9005 (Black)
Dimensions
See figures 1 and 2 below
Figure 1 - Pedestal Figure 2 - Base

Pioneer Business Park, Faraday Way, Stallingborough, DN41 8FF | 03 33300 1303 | www.myenergi.com
myenergi Ltd. | Registration No. 10261262 June 2022, Revision 1.2
D3470
12. Technical Support
If you experience any issues during or pedestal set-up, please contact our technical
support team by scanning the QR Code below.
https://myenergi.com/manual-support/
Please contact us directly for the quickest solution.