Nabis B08911 Installation instructions manual

Mono Kitchen Mixer
Instruction & Warranty Leaet
Product code:
B08911 B08912 B08913 B08914 B08915 B08917 B08921 B08923 B08925 B08926 B08927
Tap head shown is for illustration purposes only.
Please keep this instructions for future reference and request of replacement parts.

Water Regulations Requirements
It is important to ensure that the water supplies to your taps and mixers are connected in accordance with the water
regulations (WRAS) requirements and good plumbing practice.
It is Wolseley’s recommendation and good plumbing practice that the supplies of hot and cold water to the products
should be equal (balanced) pressures in order to provide a consistent ow. Supplies should be from a common source.
Either mains or tank fed. If supplies are not equal pressures then non return valves should be tted (not supplied).
There products have been designed to function on all types of water of water systems.
Please note: if a pump is to be installed to boost gravity supplies please refer to the pump manufactures instructions.
The hot and cold inlets for any of the products are hot on the left and cold on the right when viewed from the front of
the tting. It is our recommendation and good plumbing practice that a service valve also should be installed up stream
in the inlet supply lines.
Pipe Connections
IMPORTANT. Before making any inlet pipe connections all supplies MUST be thoroughly ushed to remove any
debris.
Failure to do so could result in damage or low ow from the tting.
It is a requirement of Byelaw 55 of the Water Fittings Byelaw Scheme that this function is undertaken before making
any pipe connections to supplies.
General Installation Notes
• Care must be taken during installation to prevent any risk of damage to the product or injury to installer.
• Installation must be carried out by a qualied and competent person and in accordance with the instructions supplied.
• Installations must comply with all Local and National Water Authority Regulations and Building/Plumbing
Regulations.
• Ensure that you have read and understood all sections of this manual before installation.
Water Supply Pressures
All ttings have been designed to function under the following conditions:
• Minimum supply pressure: 0.2 bar
• Maximum supply pressure: 5.0 bar
Generous ow rates are achieved at pressures as low as 0.2bar. At high pressures it maybe necessary to reduce
excessive ow rates by tting stop or servicing valves in the supply line before the mixer or tap. These stop valves
facilitate ease of maintenance should it be necessary.

Installation Requirements
Flexible Pipes Connection
Please ensure exible pipes are connected to the household pipework with extra care to avoid the exi pipes are not kinked, twist
or bent sharply.
Below are recommended ways to t the exible pipes during tap installation. Failure to follow the below recommended
guidelines may damage the exible pipes or poor taps performance.
Mono kitchen mixer
1. Identify all components and check for completeness, particularly before commencing installation.
2. Screw xing rod to tap body and tighten it.
3. Fit ange to tap body, ensuring that the anti-rotational washer is tted between the ange and the sink. if the ange is not
supplied, t anti-rotational washer directly to the tap body.
4. Screw 2x exible tails into tap body, do not over tighten.
5. Locate the tap assembly down through the tap hole in sink.
6. Slide the C shaped rubber washer and the C shaped metal washer onto the xing rod up to the underside of the sink. To secure
the mixer in place tighten the xing nut onto the xing rods until they fully tightened against the C shaped metal washer.
A suitable spanner may be required to fully tighten the xing nuts.
7. Connect the exible tails to the hot and cold water supplies.
8. Turn on the mains water supply letting the water ow for a few minutes to ush through the system.
9. Check all joints and connections for any leaks.
Tap Body
Flange (if supplied)
Anti-rotational washer
C shaped rubber washer
Fixing rod
Fixing nut
Flexible tails
C shaped metal washer
min.
80mm min.
15mm
max.
3Nm
Tap Body
Anti-rotational washer
C shaped rubber washer
Fixing rod
Fixing nut
Flexible tails
C shaped metal washer

Component Diagram
Care & Maintenance
To maintain the surface nishes, simply wipe occasionally with a mild detergent on a soft damp cloth. Dry using a soft cloth,
never use abrasive cleaners or chemical household cleaners, and avoid contact with concentrated bleach.
Nabis products are manufactured to the highest of standards and should require little or no maintenance. In the unlikely event of
any spare part requirements, please contact our free phone helpline number.
Free Phone Helpline
Should you require any technical help in association with your Nabis products please call 0344 292 7062 with your query.
Warranty: 5 Years
For detail warranty information, please visit our website: plumbcenter.co.uk
Address:
Plumb & Parts
Wolseley Center
Harrison Way
Leamington Spa
CV313HH
Website:
Plumbcenter.co.uk
WUK INST 17 Rev.1.0
5