Brodware YOKATO 1.9305.05 User manual

BASIN AND WALL MIXER
INSTALLATION INSTRUCTIONS
Brodware Industries
2 St James Place
Seven Hills NSW 2147
Australia
[phone]
brodware.com
FURTHER INFORMATION
For any further information regarding installation, cleaning
or replacement components, please do not hesitate to call
our customer service on [phone].
IMPORTANT INFORMATION
IMPORTANT
All tapware and
showers to be
installed by a licensed
plumber and to
Australian Standards.
Fit tempering and
pressure reduction
valves where required.
Flush water lines
before fitment to avoid
damage to valve.
WATER
TEMPERATURE
Is not to exceed 50ºC
as per AS3500
WATER PRESSURE
Is not to exceed
500kPa as per
AS3500
PRESSURE DIFFERENCE
Hot – Cold water pressure difference
is not to exceed 150kPa.
This product is designed to work on high
pressure systems only.
This unit cannot be used for unpressurised
storage heaters.
SHOWERS
When installing wall showers ensure that the male connecting
threads do not damage the flow controller.
CORRECT FUNCTION & MAINTENANCE
CHECK FOR CORRECT
FUNCTION AND
OPERATION
1. Pull lever – open
(water flows)
2. Depress lever – closed
3. Turn lever clockwise –
COLD water
4. Turn lever anticlockwise –
HOT water
MAINTENANCE AND
CARE / CARTRIDGE
REPLACEMENT
A. Shut off the hot and cold water supplies
B. Loosen the socket screw at the back or underside of the
handle with a 2mm Allen key and pull off lever handle
C. Remove the metal cover cap below the lever handle
D. Remove the Hex Locknut below cover cap
E. Pull out the cartridge and base ‘O’ Ring Seal
F. Replace with a genuine Brodware cartridge.
Care must be taken to ensure that the lower
‘O’ Ring Seal is located in the cartridge correctly.
H<150kPa
C
Brodware.com
A. To comply with Australian
standards, stop cocks are
to be installed below the
tail pipes
B. Fit ‘O’ ring to mixer base
C. Fit the optional base ring or
extension if required. This
is not included as standard
D. Hole size to be Ø35mm
except 9301 and 9402
which is Ø32mm
Lower mixer into basin
or counter top
E. Fit the metal washer to
underside of basin or
counter top
F. Fit the brass nut to stud
and tighten mixer into it’s
correct position
G. Check for leaks, ensure
the swivel spout is secured
with a screw
INSTALLATION BASIN OR SINK MIXER
B.A. C.
E. F.D. G.
When installing the mixer,
ensure that it is positioned
correctly, with the mixer on the
top side and the diverter on
the bottom side.
Hot water is connected to
the left, and the cold water is
connected to the right, when
viewed from the operating
position.
When the diverter handle is
rotated fully clockwise, water
is diverted to the bottom port.
Anti-clockwise rotation of the
handle diverts water to the
top port.
1.XX48.05 DIVERTOR / MIXER
INSTALLATION GUIDE
cold
holes
bottom port
top port
hot
diverter
handle
ICNMIX | BR3367 | 0816
ALL PLUMBING MUST BE TESTED BEFORE
CONCEALING / SHEETING OFF AS PER AS3500

Brodware.com
To be read in conjunction
with wall mixer information.
A. Seal and fit plug.
B. Fit and seal nipple then
tighten nuts.
C. Trial fit the wall plate
and ensure centre of mixer
to nipple is correct and
level before sheeting off.
D. Fix backing plate to wall.
E. Cut the nipple thread
to length before fitting
wall plate.
F. Tile or finish wall face.
G. City Que 1.9805.05.
Plate to fit back to the
shoulder of the nipple.
Yokato 1.9305.05.
The nipple screws in from
the front. Screw in till it
bottoms out on the plate.
H. When fitting off lock handle
and spout screws with
allen key supplied.
To be read in conjunction
with information on reverse.
Using copper tubes
supplied, rough in supply lines.
Use the template supplied to
ensure the correct spacing
of tubes.
The tubes are to be clean
and smooth with no external
damage, with the top of
the tubes clean cut and
no external burrs. Ensure
protection of tubes during
building works.
The structure is to be sufficient
to securely anchor the mixer
and tubes.
When fitting off drill floor for
fixings, ensure water lines
are flushed to remove foreign
particles. Push on flexible
connectors to supply tubes.
Supply tubes to be 25-30mm
above finished floor.
Water test before fixing down.
Remote isolating valves must
be fitted to enable ease of
service if required.
If the floor is not level, the
adjustment screws in the floor
mount can be adjusted to
ensure the mixer is vertical.
Screw down dress flange.
These instructions are to be read in
conjunction with the basic installation card.
1. Using copper tubes supplied, rough in
supply lines. Use the template supplied to
ensure the correct spacing of tubes.
2. The tubes are to be clean and smooth with
no external damage, with the top of the tubes
clean cut and no external burrs. Ensure
protection of tubes during building works.
3. The structure is to be sufficient to securely
anchor the mixer and tubes.
5. When fitting off drill floor for fixings, ensure
water lines are flushed to remove any foreign
particles. Push on flexible connectors to
supply tubes. Supply tubes to be 25-30mm
above finished floor and centered 75mm
from wall.
6. Water test before fixing down.
Remote isolating valves must be fitted to enable
ease of service if required.
If the floor is not level, the adjustment screws in
the floor mount can be adjusted to ensure the
mixer is vertical.
Screw down dress flange.
WALL MIXER INSTALLATION CITY QUE 1.9805.05, YOKATO 1.9305.05 AND 1.9306.05
WALL MIXER INSTALLATION
FLOOR MOUNTED BATH / BASIN MIXER
INSTALLATION GUIDE
1.9913.00 AND 1.9813.00
FLOOR MOUNTED SHOWER
INSTALLATION GUIDE
A
B
Front View
C
D
E
F
GH
Side View
A. Remove the handle and trim and push protective sleeve over
the body to protect from damage during tiling.
B. Install mixer to correct depth as shown in the drawing.
It is most important that the finished wall location is
determined.
Base of body to finished wall face (Length B)
Product Max Min
1.9348.00 70mm 45mm
1.9448.00 60mm 45mm
All other innwall mixers 77mm 45mm
When installing the mixer ensure that it is positioned the
correct way (as per the markings on the body) with the hot
water on the left and cold water on the right when viewed
from an operating position.
Connect mixer using union connections (not nylon olives).
Ensure mixer is level and aligned correctly.
C. Because of the speed at which single lever mixers can be
closed, they can accentuate water hammer if not properly
installed. Before sheeting walls it is important that the system
is checked for this.
If hammer is apparent, all possible measures are to be taken,
including but not limited to, correct and secure fixing of
pipework, keeping the length of the pipework on the outlet as
short as possible and the fitting of outlets that have a high star
rating
D. Check operation and test for leaks before plastering or tiling
and refit tiling sleeve. Seal around bodies to prevent water
penetration into wall
E. On completion of tiling remove tiling sleeve and fit dress ring.
Fit handle and secure with grub screw
Length BFinished
Wall
A.
B.
D. E.
C.
Mixer
Dress flange
Alan key
4x Fixing bolts
Floor mount
4x Leveling grub screws
25-35mm above finished floor
Copper tubes
Finished wall to be 75mm
from centre of water inlets
Connects
Key
4x Fixing
Bolts
Brass Flange
Mixer
4x Levelling
Grub Screws
Floor Mount
Connects
Copper Tubes
25-30mm above
finished floor