2
1. Determine mounting location. Using the template (Figure
1) and a pencil, lightly mark the location of the two mounting
holes and the two wire feed holes.
2. Route the HID Model 6005B wires. The minimum number
of wires required to activate the HID Model 6005B are dis-
played in Table 3. Determine which wires will be needed
and plan how these wires will be accessed from behind the
mounting location.
3. Install dry wall mounting hardware. Use hardware such
as molly bolts, toggle bolts or other anchoring devices. Drill
the smallest hole needed for the device. Warning: Use
caution when drilling holes--there may be high voltage wir-
ing in wall.
4. Drill wire feed holes. Minimum size for the top feed hole
(A) is 1/2", but can be made larger if necessary. Note: Do
not exceed a diameter that can be concealed by the GEM-
PXCV reader cover. The diameter of the bottom feed hole
(B) should not exceed 1/2" and should be made as small as
possible. Note: Use care to ensure that the bottom feed
hole (B) does not damage the structural integrity of the bot-
tom mounting hole anchoring device.
5. Route the HID Model 6005B wires from behind the mount-
ing location through the top wire feed hole (A).
6. Insert the 3 LED System Status wires into the bottom wire
feed hole (B) and then out of the top wire feed hole (A).
7. Connect the HID Model 6005B wires as displayed in Ta-
ble 3. Connect the GEM-PX wires as displayed in table 4,
below.
8. Note: Do not apply power until all wiring is complete.
9. Push all wires back into wall. Use care not to damage the
wiring or the mounting surface.
10. Mount HID Model 6005B Reader Base using two #4
mounting screws (supplied).
11. Install cover. Place the GEM-PXCV proximity reader cover
over the HID Model 6005B base and snap on to secure.
NOTE ON READER TYPE
The type of HID Model 6005 Reader used and the PCD-
Windows setting "Enable Card Presentation Beep and Green
LED Flash" will determine the exact operation of the Access
Status LED (see Table 1) as shown below:
HID MODEL 6005B-00 (Recommended)
•Setting Disabled: Green LED will operate when card is read.
•Setting Enabled: Green LED will double flash when card is read.
HID MODEL6005B-07
•Setting Disabled: Green LED will not flash when card is read.
•Setting Enabled: Green LED will operate when card is read.
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free
from manufacturing defects in materials and workmanship for thirty-six months following
the date of manufacture. NAPCO will, within said period, at its option, repair or replace
any product failing to operate correctly without charge to the original purchaser or user.
This warranty shall not apply to any equipment, or any part thereof, which has been
repaired by others, improperly installed, improperly used, abused, altered, damaged,
subjected to acts of God, or on which any serial numbers have been altered, defaced or
removed. Seller will not be responsible for any dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS
OR IMPLIED WARRANTY OF MERCHANTABILITY OR A WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF
ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO.
Any action for breach of warranty, including but not limited to any implied warranty of
merchantability, must be brought within the six months following the end of the warranty
period.
IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS
CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional who installed and maintains your
security system. In order to exercise the warranty, the product must be returned by the
security professional, shipping costs prepaid and insured to NAPCO. After repair or
replacement, NAPCO assumes the cost of returning products under warranty. NAPCO
shall have no obligation under this warranty, or otherwise, if the product has been
repaired by others, improperly installed, improperly used, abused, altered, damaged,
subjected to accident, nuisance, flood, fire or acts of God, or on which any serial
numbers have been altered, defaced or removed. NAPCO will not be responsible for
any dismantling, reassembly or reinstallation charges.
This warranty contains the entire warranty. It is the sole warranty and any prior
agreements or representations, whether oral or written, are either merged herein or are
expressly canceled. NAPCO neither assumes, nor authorizes any other person
purporting to act on its behalf to modify, to change, or to assume for it, any other
warranty or liability concerning its products.
In no event shall NAPCO be liable for an amount in excess of NAPCO's original
selling price of the product, for any loss or damage, whether direct, indirect, incidental,
consequential, or otherwise arising out of any failure of the product. Seller's warranty, as
hereinabove set forth, shall not be enlarged, diminished or affected by and no obligation
or liability shall arise or grow out of Seller's rendering of technical advice or service in
connection with Buyer's order of the goods furnished hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY
TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the
following: criminal tampering, electrical or communications disruption, it is possible for the
system to fail to perform as expected. NAPCO does not represent that the product/
system may not be compromised or circumvented; or that the product or system will
prevent any personal injury or property loss by burglary, robbery, fire or otherwise; nor
that the product or system will in all cases provide adequate warning or protection. A
properly installed and maintained alarm may only reduce risk of burglary, robbery, fire or
otherwise but it is not insurance or a guarantee that these events will not occur.
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL
INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE
PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in turn advise
the consumer to take any and all precautions for his or her safety including, but not
limited to, fleeing the premises and calling police or fire department, in order to mitigate
the possibilities of harm and/or damage.
NAPCO is not an insurer of either the property or safety of the user's family or
employees, and limits its liability for any loss or damage including incidental or
consequential damages to NAPCO's original selling price of the product regardless of
the cause of such loss or damage.
Some states do not allow limitations on how long an implied warranty lasts or do not
allow the exclusion or limitation of incidental or consequential damages, or differentiate in
their treatment of limitations of liability for ordinary or gross negligence, so the above
limitations or exclusions may not apply to you. This Warranty gives you specific legal
rights and you may also have other rights which vary from state to state.
NAPCO LIMITED WARRANTY
