Narvon 378SM261 User manual

1
NARVON
2.6 GALLON BOWL
FROZEN BEVERAGE
DISPENSERS
#378SM261
SINGLE BOWL
#378SM262
DOUBLE BOWL
#378SM263
TRIPLE BOWL
USER MANUAL
READ THOROUGHLY BEFORE OPERATION • UPDATED 2/2019

NARVON

1
NARVON
TABLE OF CONTENTS
SAFETY
SAFETY ....................................... 1
COMPONENTS, FEATURES & CONTROLS ...... 2
Main Components .........................................2
Technical Features .........................................2
Serial Plate................................................2
Main Control ..............................................2
Bowl Control ..............................................2
INSTALLATION ................................ 3
Unpacking ................................................3
 Posioning................................................3
Electrical Safety ...........................................3
 MainSafetyInformaon ....................................3
OPERATION................................... 4
Preparaon ...............................................4
 SlushProducon ..........................................4
Thickness Control..........................................4
 ColdDrinkProducon......................................4
CLEANING .................................... 5
Disassembly ..............................................5
 Washing&Sanizing.......................................6
Condenser Cleaning........................................6
Reassembly ...............................................7
Rinsing ...................................................8
DISPOSAL..................................... 8
TROUBLESHOOTING .......................... 9
WARRANTY..................................10
ELECTRICAL DIAGRAMS ......................11
PARTS DIAGRAMS............................12
• Thisinstruconmanualisanintegralpartofthemachineandmustbekeptforanyfurtherconsultaon.
• This machine is a cold drink dispenser.
• This machine should be used only for the purpose for which it was designed. Any other use is inappropriate and
therefor dangerous.
• The manufacturer will not be held responsible for any damage caused by improper use.
• Beforeinstallingandoperangthemachine,readthisinstruconmanualcarefully.
• Basic safety rules:
- DO NOT touch the machine when hands or feet are wet.
- DO NOT use the machine when barefoot.
-Thisapplianceshouldonlybeusedbypersonswhohavetheknowledge,experience,
and capability to operate it in a safe way.
- DO NOT allow children to play with the appliance.
- DO NOT allow the machine to be used by children or untrained persons.
- DO NOT leave the machine outdoors.
- DO NOT pull on the electrical cord to unplug the machine.

NARVON
2
COMPONENTS, FEATURES
& CONTROLS
MAIN COMPONENTS
1. Lid
2. Bowl
3. Tap Lever
4. Product Supply
5. BowlSwitchBox
6. Drip Tray
7. Thickness Control
8. Spiral Blade
9. Main Switches
10.BowlFixingKnob
11.Rubber Leg
1
7
2
8
3
9
B
B
A
A
C
10
11
4
5
6
TECHNICAL FEATURES
SERIAL PLATE
The technical features of the machine are reported on the
serialplateaachedontheframe.
Posionedontherightsideofthemachine.
Posionedunderneatheachbowl.
A - Main Power Switch
0: Machine is OFF
I: Machine is ON
B - Lid Light Switch
0: Light is OFF
I: Light is ON
A - Beverage Type Control Switch
0: Cooling OFF
 I:Slush/FrozenCreamMode
II: Cold Drink Mode
B - Spiral Blade Switch
0: Spiral Blade OFF
I: Spiral Blade ON
C - Thermostat Control
Controls the temperature of the product when
the Beverage Type Control Switch is set to II.
MAIN CONTROLS
BOWL CONTROLS
SM261 SM262 SM263
Bowls 123
Capacity 1 x 2.6 Gal 2 x 2.6 Gal 3 x 2.6 Gal
Gas R404a
Width 8.3 in 15.7 in 23.6 in
Depth 20.8 in
Height 33 in
Weight 70 lb 123 lb 158 lb
Power 530W 850W 1100W
Voltage 120V
Acousc
Pressure < 70 dB (A)
Class N
ITEM #: 378SM261
MFR MODEL #: OASIS 1-10
SPECS: 1 x 2.6 GAL • 120V • 530W
GAS/Q.TY: R134a - Gr. 140
PRESSURE: HIGH - 186 PSI • LOW - 88 PSI
SERIAL #:
MADE IN ITALY

NARVON 3
INSTALLATION
UNPACKING
POSITIONING
ELECTRIC CONNECTION
MAIN SAFETY INFORMATION
1. Removethecartonboxandtheplascbag.
2. Make sure that the machine is intact and has not been damaged
during transport.
3. Disposeofanypackagingmaterialsproperly,keepanythatyou
may need for future moves.
1. Placethemachineonasturdyhorizontalsurface.
2. Forimprovedvenlaon,maintainadistanceof10in.
between the unit and walls or other obstacles. Increase the
distanceiftheobstaclesareaheangsource.(Fig.1)
3. Leave 60 in. of free space in front of the machine to allow for
easyuseandmaintenance.(Fig.1)
4. Leave 10 in. of free space above the machine to allow for
removaloflids.(Fig.1)
5. Whenthemachineisinplace,adjusttherubberlegstolevel.
1. SettheMainPowerSwitchtoOFF(0).
2. Verify that the machine is properly grounded.
3. Verify the voltage of the outlet matches what is
indicated on the serial plate.
4. Verifythecurrentavailableissucientforthe
maximumrequiredbythemachine.
5. Inspectthecordfordamage,ifanyispresent
DO NOT plug into the outlet.
6. DONOTuseanextensioncordoradapterto
connect the machine to the electric supply.
• DO NOT touch the machine with wet hands or feet.
• DO NOT operate when barefoot.
• DO NOT allow the machine to be operated by
children or untrained persons.
• DO NOT leave the machine outside.
• DO NOT pull the cable to disconnect the machine
from the electric supply.
• DONOTplacethemachinenearammableor
explosivematerials.
• DO NOT place the machine nearby any heat source
orheangelement.
Ifindoubt,consultaspecializedelectricaltechnician.
Beforeinserngtheplugintotheelectricoutlet,
carefully verify the following:
Whenliingortransporng,
DO NOT GRAB THE MACHINE BY
THE CYLINDRICAL EVAPORATORS.
The manufacturer is not
responsible for any damage caused
by improper handling.
CAUTION
10”
10”
10”
60”
Fig. 1

NARVON
4
OPERATION
PREPARING THE PRODUCT
FROZEN BEVERAGES
COLD DRINKS
Concentrate
 Inordertoobtainahomogeneousmix,theproductwillneed
 tobepre-mixedbeforebeingaddedtothemachine.Followthe
 manufacturer’srecommendaonsformixing.
Ready-to-Use & Pre-Mixed Concentrates
1. Turn the machine OFF and unplug from power supply.
2. Pourliquidintothebowl.(Fig.2)
3. DO NOT pour below the MIN Level.
4. DO NOT pour above the MAX Level.
1. PosiontheBeverageTypeControlSwitchtoI(Slush/FrozenCreamMode).
2. PosiontheSpiralBladeSwitchtoI(ON).
3. Waitforthemixturetofreezeandtestconsistency.
Ifconsistencyisgood,connuetostep5.Ifnot,connuetostep4.
4. ThicknessControlKnobisfoundbehindthebackpanelofthemachine.
Themachineissetforopmalslushthicknessbythefactory,turnthescrew
LtoRtoincreasethickness,RtoLtodecreasethickness.(Fig.3)
5. Dispensethebeveragebypullingthetaplever.(Fig.5)
1. PosiontheBeverageTypeControlSwitchtoII(ColdDrinkMode).
2. PosiontheSpiralBladeSwitchto0(OFF).
3. Theopmaldrinktemperaturehasbeensetbythefactory.
UsetheThermostatControltoadjustthetemperatureofthedrink.
4. Tosettemperature,openthetransparentscreenonthefrontpanelbelowthe
bowl and turn the Thermostat Screw.
5. Dispensethebeveragebypullingthetaplever.(Fig.5)
Inordertoobtainaslushconsistency,themixturemusthavea
minimumsugarcontentof13°BRIX(13gsugarto100gsoluon).
Alowerconcentraonmaydamagethespiralbladesandgearmotors.
Prepare the product separately before proceeding.
It is recommended to maintain a product level above the cylinder evaporators
forconsistentcooling.(Fig.4)
Beforeusingthemachine,allfoodcontactsurfacesandcomponentsmustbecleaned
andsanizedinaccordancetotheWashing&Sanizingseconofthismanual.
Over-icingandspiralbladejammingcan
becausedbythewrongthicknessseng.
CAUTION
CAUTION

Fig. 2
Fig. 3
Fig. 4
Fig. 5

NARVON 5
CLEANING
EMPTY THE BOWL(Skipthisstepifthisistheinialcleaning)
DISASSEMBLY
Dispensing Tap(Fig.6)
Lid(Fig.7)
Bowl(Fig.8-12)
Drip Tray (Fig.13)
1. Usethetaplevertoemptyanyremainingliquidintoacontainer.
2. DO NOT proceed without emptying the bowl.
1. Place hand beneath the dispensing outlet
to catch pieces as they are released.
2. PulltheLeverPin(A)todisconnectthe
TapValve(C)andSpring(D).
3. IftheTapLever(E)istobewashed,
removeLeverPin(B).
1. Lithelidstraightupwardto
remove from the bowl.
1. Removethe(2)FrontFixingKnobsbyunscrewingthem
counter-clockwise.(Fig.8)
2. Remove the bowl from its seat. (Fig.9)
3. Gently pull on the spiral blades to remove from the cylindrical
evaporators.(Fig.10)
4. GentlypullontheSpiralBladeGaskettoremove.(Fig.11)
5. Gently pull on the Bowl Gasket to remove. (Fig.12)
1. Liupwardandthenawayfromthemachinetounseatthehooks.
2. Wash with warm water and dry.
3. Re-insert the hooks into their holes and push down.
The machine must be turned OFF and unplugged
from the power source before cleaning.
CAUTION
CAUTION
I
I
0
0
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
When cleaning
orliing,
DO NOT GRAB
THE MACHINE
BY THE
CYLINDRICAL
EVAPORATORS.
Fig. 6
AB
C
D
E

NARVON
6
WASHING & SANITIZING
CONDENSER CLEANING
WASHING
SM261(Fig.14) SM262 & SM263 (Fig.15)
SANITIZING
Tomaintainhealthstandardsandproductquality,themachineshouldbecleanedasoenaspossible.
Regularmaintenanceofthecondenserensuresthequalityoftheproductandeciencyofthemachine.
This cleaning should be performed at least once a month.
Sanizingmustbedonebeforetheinialuseofthe
machineorifitisnotusedforanextendedperiodofme.
• Fillabasinwithlukewarmwater(Approx.104°F)and
aneutraldetergentsuitableforplascitems.
• DONOTuseabrasivepowderswhichmightaect
the bowl’s transparancy.
• Washallcomponents(exceptthelid)inthebasin.
• DO NOT wash the lid by dipping in water. Doing so
may damage electric components.
• Useawet,socloth.
• Rinse all parts carefully with clean lukewarm water to
remove any residual soap.
• Dryallpartswithasocloth.
• Ifthemachinewillnotbeinuseforanextended
period,coverandkeepitawayfromdust.
• Remove the back panel by unscrewing the 4 screws.
• Useasoanddrybrushtoremovethedustfromthe
condenserns.
• Whencleaningiscomplete,replacethebackpanel
with the 4 screws.
• Removethelesidestainlesssteelpanelby
unscrewingtheFixingKnob(A)asshown.
• Useasoanddrybrushtoremovethedustfromthe
condenserns.
• Whencleaningiscomplete,replacethesidepanel
withtheFixingKnob(A).
• Followwashinginstrucons.
• Makeasoluonoflukewarmwater(Approx.104°F)
andhypochlorite(bleach)witha10gto1Lrao.
• Useasoclothorbrushtoapplythesoluon
to all components.
• Rinse all parts carefully with clean lukewarm water
toremoveanyresidualsoluon.
• Dryallpartswithasocloth.
DO NOT wash any components of the machine in the dishwasher.
The machine must be turned OFF and unplugged from the power source before cleaning.
CAUTION
CAUTION
Fig. 14 Fig. 15
A

NARVON 7
Allwashedand/orsanizedpartsmustbecompletelydrybeforebeing
carefully reassembled. Some components must be lubricated in order to
workeciently.Atubeoflubeisincludedwitheachmachine.
Fig. 16
Fig. 17
Fig. 19
Fig. 18
Fig. 20
Fig. 21
Fig. 22
CAUTION
When cleaning
orliing,
DO NOT GRAB
THE MACHINE
BY THE
CYLINDRICAL
EVAPORATORS.
REASSEMBLY
Bowl(Fig.16-20)
Lid(Fig.21)
Dispensing Tap(Fig.22)
1. PlacetheBowlGasketattheboomoftheCylinder
Evaporator,lubricangtheupperpart(A).(Fig.16)
2. Lubricatethesurfaceofthecylinderinthezoneof
thetransmissionshaoutlet(A).(Fig.17)
3. PlacetheSpiralBladeGasket(B),lubricangboththe
internalandexternalsurfaces.(Fig.17)
4. InserttheSpiralBladesothattheheadjoinsthe
transmissionsha.(Fig.18)
5. LubricatetheexternalpartoftheheadoftheSpiral
Blade(A).(Fig.18)
6. Aerallbowlcomponentsareproperlyposioned
andlubricated,slidetheBowlintoposion.(Fig.19)
7. SecurethebowlbyscrewingtheBowlFixingKnobs
clockwise.(Fig.20)
1. Placethelidoverthebowl,verifyingthecorrect
inseronoftheelectriccontacts.
1. PlacetheLever(E)inplacesoPin(B)linesup
correctly.InsertPin(B)andsecure.
2. LubricatetheTapValve(C).
3. InserttheSpring(D)intotheproductsupplyhole,
followedbythelubricatedTapValve(C)andsecure
withPin(A).
A
A
A
B
C
D
E

NARVON
8
RINSE CYCLE
USEFUL INFORMATION
DISPOSAL
REPLACING THE LID LIGHT
Aercleaning,itisnecessarytorunarinsecyclebeforeloadingproduct.
Whenthemachineisnolongerofuse,disposeofitproperly.Orifslloperaonal,sellothroughan
authorizedorganizaonorcompany.
1. Fill the bowl with clean water to the MAX Fill Line.
2. TurntheMainPowerSwitchON(I).
3. TurntheSpiralBladeON(I).
4. Let the machine run for 5 minutes.
5. Empty the bowl through the Dispensing Tap.
6. TurntheMainPowerSwitchOFF(0).
7. Useasotoweltodrytheinsideofthebowl.
1. Thecoolingperformanceofthemachineisinuencedby:
 -Externaltemperature
 -Inialproducttemperature
- Sugar percentage in the product
 -Thickness/Temperaturesengs
2. Inordertoreducestartupme,itisstronglyrecommendedthatyounotllthe
bowl with warm or room temperature products. It is recommended to chill the
product beforehand.
3. Whenrellingortoppingoaproduct,itishighlyrecommendedthatyouchill
the added product beforehand.
4. Iftheproductisamixtureofwaterandconcentrate,itneedstobemixedbefore
adding to the bowl.
1. Removethelidfromthebowl.(Fig.23)
2. Unscrewthe(2)topscrewssecuringthetoptothelidbase.
3. Replace the bulb only with a genuine spare part.
4. Securethetoptothebasewiththe(2)topscrews.
5. Reaachlidtobowl.
The machine must be turned OFF and unplugged
from the power source before maintaining.
CAUTION Fig. 23

NARVON 9
TROUBLESHOOTING
Problemsmarkedwiththissymbolmustbehandledbyaspecializedtechnician.
CAUTION
PROBLEM CAUSE SOLUTION
The machine does
not turn ON
The Main Switch is not set to I Set the Main Switch to I
The machine is not plugged in Plug the machine into the outlet
Electriccabledefecve Replace the electric cable
TheMainSwitchisdefecve Replace the switch
The machine does
not make the
product into slush
The Spiral Blade Switch is set to 0 Set the Spiral Blade Switch to I
The Beverage Type Control Switch is not set to I Set the Beverage Type Control Switch to I
Product has too high of a sugar content Remove product and dilute in a separate container
WrongThicknessControlseng SetThicknessControlcorrectly(seeFig.3)
Insucientvenlaonornearbyheatsource Movethemachinesoithasadequatevenlaon
andisfarawayfromheatsources(seeFig.1)
Leaking refrigerant Restore and re-charge the cooling system
Dustaccumulaononcondenser Cleanthecondenser(seeFig.14/15)
Themicro-switchoftheThicknessControlisdefecve Clean or replace the micro-switch
The Spiral Blade
does not turn
Spiral Blade Switch set to 0 Set Spiral Blade Switch to I
Iceaccumulaoninbowl Switch the Main Switch OFF and wait for ice to melt
SpiralBladeSwitchisdefecve Replace the Spiral Blade Switch
The Spiral Blade
makes noise Insucientlubricaon Lubricateallareascorrectly(seeFig.16-18)
Dispensing Tap
is leaking
DispensingTapValve(C)isdefecve ReplacetheTapValve(C)
Insucientlubricaon LubricateTapValve(C)correctly(seeFig.22)
Dispensing Tap does
not dispense product Iceaccumulaoninbowl Switch the Main Switch OFF and wait for ice to melt

NARVON
10
WARRANTY
6 Month Replacement Warranty
Select units are eligible for a replacement warranty for a period of 6 months from the date of purchase. It warrants to the original purchaser
ofnewNarvonBeverageEquipmentunits(andallpartsthereof),thatsuchequipmentwillbefreefromdefectsinmaterialandworkmanship.
Narvonequipmentinstalledin/onafoodtruckortrailerwillbelimitedtoaperiodof30Daysfromtheoriginaldateofpurchase.Narvon
reservestherighttoapproveordenytherepairorreplacementofanypartorrepairrequest.
NarvonBeverageEquipmentwillnotwarrantcoverageforcomponentfailureorotherdamagesthatariseunderthefollowingcondions:
• Failuretoinstalland/orusetheunitwithinproperoperangcondionsspeciedbyNarvonBeverageEquipment.
• Failuretoproperlymaintaintheunit.Thisincludes,butisnotlimitedto,basicpreventavemaintenancelikecleaningthe
 condensercoiloroperaonalexpectaons,suchaskeepingtheunitadequatelylledwithproduct.
• Installaoninnon-commercialorresidenalapplicaons.
• Products sold or used outside of the United States.
• Any damage that occurs as a result of negligence or improper handling.
• Overloadingorimproperloadingoftheunitinamannerthatpreventsproperairow.
Addionally,noclaimscanbemadeagainstthiswarrantyforspoilageofproducts,lossofsalesorprots,oranyotherconsequenaldamages.
Normalweartypeparts,suchaslightbulbsandgaskets,arenotincludedinwarrantycoverage.
What This Warranty Does Not Cover:
This warranty is only valid on equipment purchased from an authorized dealer.
Failure to contact Narvon Beverage Equipment prior to obtaining equipment service may void your warranty.
ThisstatestheexclusiveremedyagainstNarvonrelangtotheproduct(s)whetherincontractorintortorunderanyotherlegaltheory,and
whetherarisingoutofwarranes,representaons,instrucon,installaon,ordefectsfromanycause.Narvonshallnotbeheldliablewhether
incontractorintortorunderanyotherlegaltheory,forlossofrevenueorprot,orforanysubstuteuseorperformance,orforincidental,
indirect,specialorconsequenaldamages,orforanyotherlossorcostofsimilartype,includingwithoutlimitaon,lossesordamagesarising
from food or product spoilage.

NARVON 11
ELECTRICAL DIAGRAMS
Lighting Scheme
0 I
0 I
0II I
0 I
0II I
Lighting Scheme
0 I
0 I
0II I
0 I
0II I
0 I
0II I
Lighting Scheme
S Main power switch
G 1,2,3 Motor-gearbox
FM Fan motor
C Compressor
T 1,2,3 Drink thermostat
SD 1,2,3 Thickness micro-switch
EV 1,2,3 Electrovalve
TR Transformer
L 1,2,3 Light
SM 1,2,3 Spiral blade switch
SGB 1,2,3 Slush/drink switch
TD Timer
FU Fuse
SL Light Switch
SM261
SM262
SM263

NARVON
12
23
37
3
5
4
2
17
16
15
14
13
9
11
12
10
8 6
28
27
26
30
31
24
25
20
19
21
34
33
32
35
1
47
38
44
42
41
40
48
Lubrificante
49
50
Fuse
29
7
46
18
22
43
36
52
53
45
54
51

NARVON 13
PARTS DIAGRAM - SM261
NO. CODE DESCRIPTION
1 2107 Lid
2 2122 Screen for lid
3 2158 12V-3W lamp led
4 2127 Under-lid
5 2112 Spiral blade
6 2133 Bowl Oasis 10Lt
7 2150 Rotaon pin
8 2117 Tap lever
9 2149 Fixing knob
10 2120 Tap spring
11 2134 Tap valve
12 2113 Spiral blade
13 2115 Spiral blade gasket
14 2137 Slush/Drink switch
15 56 Spiral blade switch
16 2160 Thermostat
17 2161 Complete drip tray
18
182 Fan motor 220-240V - 50/60Hz
68 Fan motor 115V - 60Hz
19 0159 Rubber leg H=35
20
2164 Compressor 220-240V-50Hz
2165 Compressor 115V-60Hz
21
2162 Timer 220V (4 min)
2163 Timer 115V (4min)
22
2166 Transformer 220-240V - 50Hz
2167 Transformer 115V - 60Hz
23 2157 Thickness control spring
24 56 Light switch
25 57 Main switch
26 2108 Back support cover
27 2131 Motor-gearbox support
28 2121 Motor-gearbox 220/115V-50/60hz
NO. CODE DESCRIPTION
29 2168 Micro-switch
30 2116 Bowl gasket
31 2110 Evaporator
32 2145 Evaporator cover
33 2101 Transmission sha
34 2111 Metal ring M25
35 2123 Evaporator cover inner OR (small)
36 154 Evaporator cover inner OR (large)
37 2159 Complete lid
38
54 Cable cord 220V
407 Cable cord 115V
40 2169 Thickness control knob
41 2125 Evaporator plate
42 2126 Switches box
43 2148 Side panel
44 2172 Fuse
45 2220 Front panel
46 2174 Back panel
47 2175,01 Condenser
48
2164,01 Electric parts kit 220-240V-50Hz
2165,01 Electric parts kit 115V-60Hz
49 2118 Lubricant tube
50 2103 Electric contact sha
52 2133,01 Bowl Kream line 6 Lt
53 2107,02 Kream line lid

NARVON
14
3
21
24
25
17
13
16
15
14
18
20
19
28
22
9
11
29
27
26
12
5
4
2
10
8 6
34
33
32
35
30
31
37
1
23
40
Lubrificante
49
45
38
48
41
Fuse
50
44
43
51
46
7
42
36
52
53
47

NARVON 15
PARTS DIAGRAM - SM262
NO. CODE DESCRIPTION
1 2107 Lid
2 2122 Screen for lid
3 2158 12V-3W lamp led
4 2127 Under-lid
5 2112 Spiral blade
6 2133 Bowl Oasis 10Lt
7 2150 Rotaon pin
8 2117 Tap lever
9 2149 Fixing knob
10 2120 Tap spring
11 2134 Tap valve
12 2113 Spiral blade
13 2115 Spiral blade gasket
14 2137 Slush/Drink switch
15 56 Spiral blade switch
16 2160 Thermostat
17 2161 Complete drip tray
18
2138 Fan motor 220-240V - 50/60Hz
2208 Fan motor 115V - 60Hz
19 2153 Rubber leg H=35
20
2186 Compressor 220-240V-50Hz
2187 Compressor 115V-60Hz
21
2143 Electrovalve complete 220V
2184 Electrovalve complete 115V
22
2166 Transformer 220-240V - 50Hz
2167 Transformer 115V - 60Hz
23 2157 Thickness control spring
24 56 Light switch
25 57 Main switch
26 2108 Back support cover
27 2131 Motor-gearbox support
28 2121 Motor-gearbox 220/115V-50/60hz
NO. CODE DESCRIPTION
29 2168 Micro-switch
30 2116 Bowl gasket
31 2110 Evaporator
32 2145 Evaporator cover
33 2101 Transmission sha
34 2111 Metal ring M25
35 2123 Evaporator cover inner OR (small)
36 154 Evaporator cover inner OR (large)
37 2159 Complete lid
38
54 Cable cord 220V
407 Cable cord 115V
40 2169 Thickness control knob
41 2125 Evaporator plate
42 2126 Switches box
43 2148 Side panel
44 2172 Fuse
45 2220 Front panel
46 2174,01 Back panel
47 2146,01 Condenser
48
2186,01 Electric parts kit 220-240V-50Hz
2187,01 Electric parts kit 115V-60Hz
49 2118 Lubricant tube
50 2103 Electric contact sha
51
2105 Coil 220V - 50/60 Hz
2183 Coil 115V - 50/60 Hz
52 2133,01 Bowl Kream line 6 Lt
53 2107,02 Kream line lid

NARVON
16
6
8
10
2
4
5
12
26
27
11
9
28
13
17
25
24
3
37
14
15
16
30
31
34
33
32
35
22
Fuse
44
Lubrificante
49
18
20
19
38
48
43
23
40
29
50
1
42
7
45
46
41
52
53
47
36
21
51

NARVON 17
PARTS DIAGRAM - SM263
NO. CODE DESCRIPTION
1 2107 Lid
2 2122 Screen for lid
3 2158 12V-3W lamp led
4 2127 Under-lid
5 2112 Spiral blade
6 2133 Bowl Oasis 10Lt
7 2150 Rotaon pin
8 2117 Tap lever
9 2149 Fixing knob
10 2120 Tap spring
11 2134 Tap valve
12 2113 Spiral blade
13 2115 Spiral blade gasket
14 2137 Slush/Drink switch
15 56 Spiral blade switch
16 2160 Thermostat
17 2161 Complete drip tray
18
2139 Fan motor 220-240V - 50/60Hz
2218 Fan motor 115V - 60Hz
19 2153 Rubber leg H=35
20
2188 Compressor 220-240V-50Hz
2189 Compressor 115V-60Hz
21
2144 Electrovalve complete 220V
2144,01 Electrovalve complete 115V
22
2166 Transformer 220-240V - 50Hz
2167 Transformer 115V - 60Hz
23 2157 Thickness control spring
24 56 Light switch
25 57 Main switch
26 2108 Back support cover
27 2131 Motor-gearbox support
28 2121 Motor-gearbox 220/115V-50/60hz
NO. CODE DESCRIPTION
29 2168 Micro-switch
30 2116 Bowl gasket
31 2110 Evaporator
32 2145 Evaporator cover
33 2101 Transmission sha
34 2111 Metal ring M25
35 2123 Evaporator cover inner OR (small)
36 154 Evaporator cover inner OR (large)
37 2159 Complete lid
38
54 Cable cord 220V
407 Cable cord 115V
40 2169 Thickness control knob
41 2125 Evaporator plate
42 2126 Switches box
43 2148 Side panel
44 2172 Fuse
45 2220,02 Front panel
46 2174,02 Back panel
47 2146,02 Condenser
48
2188,01 Electric parts kit 220-240V-50Hz
2189,01 Electric parts kit 115V-60Hz
49 2118 Lubricant tube
50 2103 Electric contact sha
51
2105 Coil 220V - 50/60 Hz
2183 Coil 115V - 50/60 Hz
52 2133,01 Bowl Kream line 6 Lt
53 2107,02 Kream line lid