National Instruments NI myDAQ User manual
ni.com/mydaq
Contents I Contenu I Inhalt
内容 I 내용 I 内容
NI myDAQ
Quick Start
Démarrage rapide
Erste Schritte
クイッ クス ター ト
시작하기
快速入门
373059C-01 May16
Caution Before installing your device, read all product
documentation to ensure compliance with safety, EMC, and
environmental regulations.
Attention Avant d’installer votre périphérique, lisez toute la
documentation se rapportant au produit pour vous assurer du respect
des règles concernant la sécurité, la CEM et l’environnement.
Achtung Lesen Sie vor dem Einbauen des Geräts die
Produktdokumentation, um sich über alle einzuhaltenden Sicherheits-
vorschriften, EMV-Vorschriften und Umweltrichtlinien zu informieren.
注意 デバイスを取り付ける前に、すべての製品ドキュメントをお読みに
なり、安全、EMC、環境規制を遵守してください。
주의 디바이스를 설치하기 전에 모든 제품 관련 문서를 읽고 안전,
EMC, 환경 규정을 준수하는지 확인하십시오.
警告 安装设备之前，请阅读所有产品文档，确保符合安全、EMC以
及环境法规。
Useful Links I Liens utiles I Nützliche Links
役に立つリンク I 유용한 링크 I 相关链接
Getting Started/Support
ni.com/mydaq/support
Specifications
ni.com/infoamydaqspecs
Software
ni.com/downloads
© 2012–2016 National Instruments Corp.
All rights reserved.
DEVICE CONNECTIONS
Screw Terminal Connections
• +15V: Power supply (32 mA max output current1)
• –15V: Power supply (32 mA max output current1)
• AGND: Ground for ±15 V power supplies, AO, and AI
• AO: Analog output (±10 V, 200 kSamples/second max update rate, 2 mA max
output current per line1)
• AGND: Ground for ±15 V power supplies, AO, and AI
• AI: Analog input (±10 V, 200 kSamples/second max sample rate)
• DIO: 5 V compatible LVTTL input, 3.3 V LVTTL output (4 mA max output
current per line1)
• DGND: Ground for DIO and 5 V power supply
• +5V: Power supply (4.0 to 5.2 V, 100 mA max output current1)
Interface Connections
• USB: Type A to B, direct connect or powered hub only
DMM Connections
• HI [V, Ω, ]: Voltage, resistance, and diode measurement positive input terminal
(60 VDC, 20 Vrms max input voltage)
• COM: Common reference for all DMM measurements
• HI [A]: Current measurement positive input terminal (1 A max input current)
Audio Connections
• AUDIO IN: 3.5 mm stereo jack (±2 V LINE IN or microphone)
• AUDIO OUT: 3.5 mm stereo jack (±2 V LINE OUT)
1Total power is limited to 500 mW (typical)/100 mW (minimum) for all outputs and supplies.
Refer to the NI myDAQ User Guide and Specifications for how to calculate total power.
Projects and Example Code
ni.com/mydaqzone
USB Cable
DMM Cables
T
erminal Connector
Software
Audio Cables
NI myDAQ
NI myDAQ
AnalogICs
supplied by
Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for more information on National
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their
respective companies. For patents covering National Instruments products/technology, refer to the appropriate
location:
Help»Patents
in your software, the patents.txt file on your media, or the National Instruments
Patents Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and
third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/
legal/export-compliance for the National Instruments global trade compliance policy and how to obtain
relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE
ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.
Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable
limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
NI myDAQ User Manual
ni.com/infoamydaqug
ni.com/mydaq
Contents I Contenu I Inhalt
内容 I 내용 I 内容
NI myDAQ
Quick Start
Démarrage rapide
Erste Schritte
クイッ クス ター ト
시작하기
快速入门
373059C-01 May16
Caution Before installing your device, read all product
documentation to ensure compliance with safety, EMC, and
environmental regulations.
Attention Avant d’installer votre périphérique, lisez toute la
documentation se rapportant au produit pour vous assurer du respect
des règles concernant la sécurité, la CEM et l’environnement.
Achtung Lesen Sie vor dem Einbauen des Geräts die
Produktdokumentation, um sich über alle einzuhaltenden Sicherheits-
vorschriften, EMV-Vorschriften und Umweltrichtlinien zu informieren.
注意 デバイスを取り付ける前に、すべての製品ドキュメントをお読みに
なり、安全、EMC、環境規制を遵守してください。
주의 디바이스를 설치하기 전에 모든 제품 관련 문서를 읽고 안전,
EMC, 환경 규정을 준수하는지 확인하십시오.
警告 安装设备之前，请阅读所有产品文档，确保符合安全、EMC以
及环境法规。
Useful Links I Liens utiles I Nützliche Links
役に立つリンク I 유용한 링크 I 相关链接
Getting Started/Support
ni.com/mydaq/support
Specifications
ni.com/infoamydaqspecs
Software
ni.com/downloads
© 2012–2016 National Instruments Corp.
All rights reserved.
DEVICE CONNECTIONS
Screw Terminal Connections
• +15V: Power supply (32 mA max output current1)
• –15V: Power supply (32 mA max output current1)
• AGND: Ground for ±15 V power supplies, AO, and AI
• AO: Analog output (±10 V, 200 kSamples/second max update rate, 2 mA max
output current per line1)
• AGND: Ground for ±15 V power supplies, AO, and AI
• AI: Analog input (±10 V, 200 kSamples/second max sample rate)
• DIO: 5 V compatible LVTTL input, 3.3 V LVTTL output (4 mA max output
current per line1)
• DGND: Ground for DIO and 5 V power supply
• +5V: Power supply (4.0 to 5.2 V, 100 mA max output current1)
Interface Connections
• USB: Type A to B, direct connect or powered hub only
DMM Connections
• HI [V, Ω, ]: Voltage, resistance, and diode measurement positive input terminal
(60 VDC, 20 Vrms max input voltage)
• COM: Common reference for all DMM measurements
• HI [A]: Current measurement positive input terminal (1 A max input current)
Audio Connections
• AUDIO IN: 3.5 mm stereo jack (±2 V LINE IN or microphone)
• AUDIO OUT: 3.5 mm stereo jack (±2 V LINE OUT)
1Total power is limited to 500 mW (typical)/100 mW (minimum) for all outputs and supplies.
Refer to the NI myDAQ User Guide and Specifications for how to calculate total power.
Projects and Example Code
ni.com/mydaqzone
USB Cable
DMM Cables
T
erminal Connector
Software
Audio Cables
NI myDAQ
NI myDAQ
AnalogICs
supplied by
Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for more information on National
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their
respective companies. For patents covering National Instruments products/technology, refer to the appropriate
location:
Help»Patents
in your software, the patents.txt file on your media, or the National Instruments
Patents Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and
third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/
legal/export-compliance for the National Instruments global trade compliance policy and how to obtain
relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE
ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.
Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable
limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
NI myDAQ User Manual
ni.com/infoamydaqug
Or
ni.com/downloads
Install software off the media or from ni.com/downloads. (Application development software,
such as LabVIEW, then NI ELVISmx driver software.)
Connect the NI myDAQ to your computer using the enclosed USB cable. Connect the DMM
cables to the NI myDAQ.
Installez les logiciels à partir du média ou de ni.com. (Logiciels de développement d’application,
tels que LabVIEW, puis le driver NI ELVISmx.)
Installieren Sie die Software mithilfe des Datenträgers oder von ni.com/downloads(erst die
Entwicklungsumgebung, z. B. LabVIEW, und dann den NI-ELVISmx-Treiber).
ソフトウェアをメディアまたはni.com/downloadsからインストールします（LabVIEWなどのアプ
リケーション開発ソフトウェア、その後にNI ELVISmxドライバソフトウェア）。
설치미디어를 사용하여 소프트웨어를 설치합니다. (LabVIEW와 같은 어플리케이션 개발 소프트
웨어 설치 후, NI ELVISmx 드라이버 소프트웨어 설치.)
Select Start»All Programs»National Instruments»NI ELVISmx for NI ELVIS &
NI myDAQ»NI ELVISmx Instrument Launcher. Click Digital Multimeter.
Connectez le périphérique NI myDAQ à l’ordinateur à l’aide du câble USB fourni. Connectez les
câbles DMM au NI myDAQ.
Schließen Sie das NI myDAQ mit dem mitgelieferten USB-Kabel an den Computer an. Verbinden
Sie die DMM-Kabel mit dem NI myDAQ.
保護カバー付きUSBケーブルを使用して、NI myDAQをコンピュータに接続します。DMMケー
ブルをNI myDAQに接続します。
키트의 USB 케이블을 사용하여 NI myDAQ을 컴퓨터에 연결합니다. DMM 케이블을 NI myDAQ
에 연결합니다.
使用封闭式USB线缆连接NI myDAQ至计算机。连接DMM线缆至NI myDAQ。
Sélectionnez
Démarrer»Tous les programmes»National Instruments»NI ELVISmx for
NI ELVIS & NI myDAQ»NI ELVISmx Instrument Launcher. Cliquez sur
Digital Multimeter
.
Klicken Sie auf Start»Alle Programme»National Instruments»NI ELVISmx for NI ELVIS &
NI myDAQ»NI ELVISmx Instrument Launcher. Klicken Sie auf
Digital Multimeter
.
スタート»すべてのプログラム»National Instruments»NI ELVISmx for NI ELVIS & NI myDAQ»
NI ELVISmx Instrument Launcherを選択します。
Digital Multimeter
をクリックします。
시작»모든 프로그램National Instruments»NI ELVISmx for NI ELVIS & NI myDAQ»
NI ELVISmx Instrument Launcher를를 선택합니다. Digital Multimeter을클릭합니다.
4
4
Specify Range
Run Continuously
Dev1 (NI myDAQ)
(or the device number of your myDAQ)
20 V
3
3
2
2
1
1
从光盘安装，或从ni.com/downloads下载安装程序进行安装。（先安装LabVIEW等应用程序开发软
件，然后安装NI ELVISmx驱动程序。）
选择开始»所有程序»National Instruments»NI ELVISmx for NI ELVIS & NI myDAQ»
NI ELVISmx Instrument Launcher，单 击 Digital Multimeter打开界面。
Configure the Measurement Settings of the DMM soft front panel instrument and click Run. Measure the voltage of a known voltage source (such as a AA battery). 60 VDC/20 Vrms max. DO NOT plug DMM cables into circuits with Hazardous Voltage, such as wall outlets. Click Stop
when finished.
Configurez les paramètres de mesure de la face-avant logicielle de l’instrument DMM puis cliquez sur le bouton
Run
. Mesurez la tension d’une source de tension connue (telle qu’une pile AA).
60 VDC/20 Veff max
. NE PAS brancher de câbles DMM à des circuits à tension dangereuse, tels que
des prises murales. Cliquez sur le bouton
Stop
lorsque vous avez terminé.
Nehmen Sie auf dem Soft-Frontpanel des Multimeters die gewünschten Einstellungen vor und klicken Sie auf
Run
. Messen Sie die Spannung einer bekannten Spannungsquelle, z. B. einer AA-Batterie (
max. 60 VDC/20 Ueff
). Die DMM-Messfühler dürfen auf keinen Fall mit gefährlichen
Spannungen (z. B. Netzspannungen) in Kontakt kommen. Klicken Sie auf
Stop
, wenn Sie fertig sind.
DMMソフトフロントパネル計測器の測定設定を構成し、Runをクリックします。最大60 VDC/20 Vrmsの既知の電圧ソース（単三電池など）の電圧を測定します。DMMケーブルを危険電圧が印加された回路（壁のコンセントなど）に接続しないでください。終了したらStopをクリックします。
DMM 소프트 프런트 패널 인스트루먼트의 Measurement Settings를 설정하고
Run
을 클릭합니다. AA 배터리와 같이 값을 이미 알고 있는 전압 소스의 전압을 측정합니다. 최대 한도는
60 VDC/20 Vrms
입니다. DMM 케이블을 벽 콘센트와 같이 위험 전압이 발생할 수 있는 회로에 연결하지
마십시오. 측정을 마치면
Stop
을 클릭합니다.
配置DMM软面板仪器的测量设置并单击
Run
，测量已知电压源（例如，AA电池）的电压。最大测量值为
60 VDC/20 Vrms
。请勿连接DMM线缆至危险电压电路（例如，壁装插座）。测量完成后单击
Stop
。
Or
ni.com/downloads
Install software off the media or from ni.com/downloads. (Application development software,
such as LabVIEW, then NI ELVISmx driver software.)
Connect the NI myDAQ to your computer using the enclosed USB cable. Connect the DMM
cables to the NI myDAQ.
Installez les logiciels à partir du média ou de ni.com. (Logiciels de développement d’application,
tels que LabVIEW, puis le driver NI ELVISmx.)
Installieren Sie die Software mithilfe des Datenträgers oder von ni.com/downloads(erst die
Entwicklungsumgebung, z. B. LabVIEW, und dann den NI-ELVISmx-Treiber).
ソフトウェアをメディアまたはni.com/downloadsからインストールします（LabVIEWなどのアプ
リケーション開発ソフトウェア、その後にNI ELVISmxドライバソフトウェア）。
설치미디어를 사용하여 소프트웨어를 설치합니다. (LabVIEW와 같은 어플리케이션 개발 소프트
웨어 설치 후, NI ELVISmx 드라이버 소프트웨어 설치.)
Select Start»All Programs»National Instruments»NI ELVISmx for NI ELVIS &
NI myDAQ»NI ELVISmx Instrument Launcher. Click Digital Multimeter.
Connectez le périphérique NI myDAQ à l’ordinateur à l’aide du câble USB fourni. Connectez les
câbles DMM au NI myDAQ.
Schließen Sie das NI myDAQ mit dem mitgelieferten USB-Kabel an den Computer an. Verbinden
Sie die DMM-Kabel mit dem NI myDAQ.
保護カバー付きUSBケーブルを使用して、NI myDAQをコンピュータに接続します。DMMケー
ブルをNI myDAQに接続します。
키트의 USB 케이블을 사용하여 NI myDAQ을 컴퓨터에 연결합니다. DMM 케이블을 NI myDAQ
에 연결합니다.
使用封闭式USB线缆连接NI myDAQ至计算机。连接DMM线缆至NI myDAQ。
Sélectionnez
Démarrer»Tous les programmes»National Instruments»NI ELVISmx for
NI ELVIS & NI myDAQ»NI ELVISmx Instrument Launcher. Cliquez sur
Digital Multimeter
.
Klicken Sie auf Start»Alle Programme»National Instruments»NI ELVISmx for NI ELVIS &
NI myDAQ»NI ELVISmx Instrument Launcher. Klicken Sie auf
Digital Multimeter
.
スタート»すべてのプログラム»National Instruments»NI ELVISmx for NI ELVIS & NI myDAQ»
NI ELVISmx Instrument Launcherを選択します。
Digital Multimeter
をクリックします。
시작»모든 프로그램National Instruments»NI ELVISmx for NI ELVIS & NI myDAQ»
NI ELVISmx Instrument Launcher를를 선택합니다. Digital Multimeter을클릭합니다.
4
4
Specify Range
Run Continuously
Dev1 (NI myDAQ)
(or the device number of your myDAQ)
20 V
3
3
2
2
1
1
从光盘安装，或从ni.com/downloads下载安装程序进行安装。（先安装LabVIEW等应用程序开发软
件，然后安装NI ELVISmx驱动程序。）
选择开始»所有程序»National Instruments»NI ELVISmx for NI ELVIS & NI myDAQ»
NI ELVISmx Instrument Launcher，单 击 Digital Multimeter打开界面。
Configure the Measurement Settings of the DMM soft front panel instrument and click Run. Measure the voltage of a known voltage source (such as a AA battery). 60 VDC/20 Vrms max. DO NOT plug DMM cables into circuits with Hazardous Voltage, such as wall outlets. Click Stop
when finished.
Configurez les paramètres de mesure de la face-avant logicielle de l’instrument DMM puis cliquez sur le bouton
Run
. Mesurez la tension d’une source de tension connue (telle qu’une pile AA).
60 VDC/20 Veff max
. NE PAS brancher de câbles DMM à des circuits à tension dangereuse, tels que
des prises murales. Cliquez sur le bouton
Stop
lorsque vous avez terminé.
Nehmen Sie auf dem Soft-Frontpanel des Multimeters die gewünschten Einstellungen vor und klicken Sie auf
Run
. Messen Sie die Spannung einer bekannten Spannungsquelle, z. B. einer AA-Batterie (
max. 60 VDC/20 Ueff
). Die DMM-Messfühler dürfen auf keinen Fall mit gefährlichen
Spannungen (z. B. Netzspannungen) in Kontakt kommen. Klicken Sie auf
Stop
, wenn Sie fertig sind.
DMMソフトフロントパネル計測器の測定設定を構成し、Runをクリックします。最大60 VDC/20 Vrmsの既知の電圧ソース（単三電池など）の電圧を測定します。DMMケーブルを危険電圧が印加された回路（壁のコンセントなど）に接続しないでください。終了したらStopをクリックします。
DMM 소프트 프런트 패널 인스트루먼트의 Measurement Settings를 설정하고
Run
을 클릭합니다. AA 배터리와 같이 값을 이미 알고 있는 전압 소스의 전압을 측정합니다. 최대 한도는
60 VDC/20 Vrms
입니다. DMM 케이블을 벽 콘센트와 같이 위험 전압이 발생할 수 있는 회로에 연결하지
마십시오. 측정을 마치면
Stop
을 클릭합니다.
配置DMM软面板仪器的测量设置并单击
Run
，测量已知电压源（例如，AA电池）的电压。最大测量值为
60 VDC/20 Vrms
。请勿连接DMM线缆至危险电压电路（例如，壁装插座）。测量完成后单击
Stop
。
