New Classic Home Furnishings 1415-9 User manual

1415-9 Bunk Bed Assembly Instructions
-Use Only standard Twin size mattress (75”long x 39” wide)-
-Maximum mattress thickness must not exceed 8”-
-Surface of mattress must be at least 5”below the upper edge guardrails-
Top Bunk Weight Limit 200 Lbs

1415-9 Bunk Bed Assembly lnstructions
Please read the instructions and verify that all parts listed on the parts list are complete
Long Bolt31/4inches(N)
Short Bolt21/2inches(M)
Allen Wrench
Barrel Nut Part(P)
Mattress Slde Rail Part(E)
Ladder Side Rail Part(EL)
Mattress Support Slats Part(F)
Upper Quard Rail Part(H)
Guard Rail Post Part(I) Steel Connector Plh Part(K)
Ladder Hook Part(Q)
Upper Guard Rail Part(G)
Ladder Parts
J-L J-R
J-2
Upper Head Board Part(C)
Lower Head Board Part(A)
Lower Head Board Part(B)
Upper Head Board Part(D)
Parts List
Part #
Qty
Description
Part #
Qty
Description
A
1
Lower Headboard
J- L
1
Vertical Ladder Support. (left)
B
1
Lower Footboard
J-R
1
Vertical Ladder Support. (right)
C
1
Upper Headboard
J-2
4
Ladder Steps
D
1
Upper Footbaord
K
4
Steel Bed Connector Pins
E
3
Mattress Side Rails
L
66
1” Black Wood Screws
EL
1
Ladder Side Rail
Tool
1
Allen Wrench
F
2
Mattress Support Slat Sets
M
8
2 ½” Guard Rail Post Bolts
G
1
74” Upper Guard Rails (For Back)
N
22
3 ¾” Rail Bolts
H
1
57” Upper Guard Rails (For Front)
P
32
Barrel Nuts
I
1
Upper Front Guard Rail Post
Q
4
Ladder Hooks
W
2
1 ½” Rail Bolts
O
2
4” Rail Bolts

1415-9 Bunk Bed Assembly Instructions.
Barrel Nut
Mattress Support Slats
Step 2 Assembling Support Slats
Layout the Mattress Support Slats (F) with the webbing facing down.
Insert the slats into the slots in the Mattress Side Rails. Make sure every slot has a slat.
Screw in each end of the slats using the 1”Wood Screws (L) through the pre drilled holes in the slats.
Step 1 Assembling Lower Bunk
Insert 2 Barrel Nuts (P) into each end of the Mattress Side Rails (E). Be sure the long slot on the Barrel Nut is
facing out and towards the end of the side rail.
Attach the side rail to the headboard (A) by inserting 2- 3 3/4”Rail Bolts (N) through the holes in the post of the
Headboard and into the Barrel Nut in the side rail. Slat slots must face in. Screw in only part way using the
Allen Wrench provided.
Repeat this procedure until all 4 corners are attached to both headboard (A) and footboard (B).
Tighten all bolts

Please follow the Upper Bunk Assembly instructions carefully to insure a safe and sturdy bed.
Step 3 Assembling Upper Bunk
DO NOT FULLY TIGHTEN ANY BOLTS UNTIL ALL UPPER BUNK PIECES ARE CONNECTED
The Upper Footboard should be positions so the Post with the two holes is facing towards the front.
Back Side –Use the holes that are at the back of the bunk head & footboards to make the following connections
Attach mattress side rail (E) to upper Headboard (C) into the bottom two holes of the headboard. There a six
holes in the headboard; make sure to secure the mattress rail to the bottom two.
Attach the upper footboard (D) using the Barrel Nuts (P) and Rail Bolts (N). (As in Step 1).
WARNING Label on Headboard must face out away from bed.
Front Side- Use the holes that are at the front of the bunk head & footboards to make the following connections
Attach Front Ladder Side Rail (EL) to headboard (C) and foot board(D).
Install Mattress Support Slats (F) as in step 2
Attach Guardrails: (Curved edge of all guard rails must be facing down)
Attach 2 - 74”Guardrails (G) to the back portion of the upper bunk using the steps described in Step 1. The
curved edge must be facing down.
Mount Guard Rail Post (L) to the front side of Ladder Side Rail (EL) using 2- 1 ½” bolts (M). No Barrel Nuts are
required.
Attach 2- 57”Guard Rails from the Guard Rail Post (L) to the foot board (D) using 3 3/4”Rail Bolt (N) and
Barrel Nuts (P). Curved edge of both Guard Rails must be at the bottom facing down.
Tighten all bolts.

Solid Oak Bunk Bed Assembly Instructions
Step 4. Connecting Bunk Beds
Insert Steel Connector Pins (K) into holes on top of lower bunk posts. Pins should extend 1 1/4”above post.
Place top bunk over pins and onto Lower bunk.
Step 5. Assembling Ladder
Attach left ladder support (J-L) to steps (part J-2) using Barrel Nuts (P). The top of the ladder supports have 2 predrilled
holes for securing ladder hooks. Make sure to face those holes toward the top before assembling steps. Barrel Nut
holes must be on the under side of each step facing down.
Repeat with right ladder support (J-R).
Each ladder support has 2 pre drilled holes at the top for the ladder hooks (Q). Attach the Ladder Hooks (Q) using 2
wood screws (L) .
Hook the ladder securely over the top of the Ladder side rail between the guard rail post and the head.
Secure hook to the ladder side rail using 2 wood screws (L) through the hole in the ladder hook. Ladder must only be
used in this location and secured with 2 screws.
Upper Head Board
Lower Head Board
Short Bolt21/2inches
Ladder Hook
Steel Connector Plh
Ladder Parts

Bunk Bed Safety Warnings
Follow the Information on the warnings appearing on the Upper bunk end structure and on
the carton. Do Not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent
the likelihood of entrapment or falls.
Surface of mattress must be at least 5”(127mm) below the upper edge guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their
proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk.
The use of water or sleep flotation mattress is prohibited.
Keep these instructions for future reference