Newtech Casalino BTW Toilet Suite 8070 User manual

Casalino BTW
Toilet Suite
Installation Instructions
0800 728 662
www.newtech.co.nz
Casalino
Toilets
Casalino Compac
BTW Toilet Suite
8070 8090

| CASALINO BACK TO WALL TOILETS www.newtech.co.nz2
8070 Model:
Trap-60: 60~115 mm
Trap-100: 100~165 mm
JT43 connector: 150~205 mm
P-trap: 180 mm
* Rough in position of water inlet, waste outlet and
floor fixing bracket holes Ensure inlet connection
extends 60mm from finished wall. Drill holes for
floor fixing bracket then fix brackets to floor.
* Lubricate the fins
of the pan bend
and position into
waste pipe.
* Please measure existing toilet pan
to setup p trap from wall to spigot
distance. Dierent toilet suite may
have dierent set out
* Set up waste pipe and the end of the
pan collar extends approx. Minimum of
50mm onto spigot.
* Lubricate rubber
on the exposed
connector end.
“S” TRAP installation:
“P” TRAP installation:
Important
25mm approx
projection from
wall 1/2” B.S.P
Nipple
180
Min of 50mm
onto spigot
Approximately
STEP 1:
Decide if a “s” trap installation or “p” trap installation is required
8090 Model:
Trap-60: 60~110 mm
Trap-100: 100~170 mm
JT43 connector: 150~210 mm
P-trap: 180 mm

CASALINO BACK TO WALL TOILETS |www.newtech.co.nz 3
STEP 2:
1. Place rubber seal into pan recess (Do not use sealant).
2. Press Pan screw A into the pan screw hole.
3. Use Nut B to tight pan screw A underneath the pan. (refer to Fig 1).
4. Place cistern screw C into holes on the inside of cistern, making sure washers
are located correctly.
* Fit o stop tap then connect
rear water inlet valve to stop
tap. Fill cistern and ensure
correct water level
* Remove cap from cistern plug A or B at base
cistern. Connect flexible hose to cistern plug A or
B depending on location of stop tap. Complete
stop tap connection to underside of cistern plug A
or B. Fill cistern and ensure correct water level.
Note: Inlet valve can be adjusted if required.
For back inlet For bottom inlet
Do the below installation for the cistern fixing.
STEP 2 : Do the below installation for the cistern fixing.
* Place rubber seal into pan recess (Do not use sealant)
* Press Pan screw A into the pan screw hole.
* Use Nut B to tight pan screw A underneath the pan. (refer to Fig 1).
* Place cistern screw C into holes on the inside of cistern, making sure washers are
located correctly.
STEP 3:
* Align and push fully assembled toilet back
to wall, connecting pan spigot to pan collar.
Bucket flush and check for leaks. Due to the
design, weight and stability of the pan and
cistern, a silcone adhesive only is
recommended and excepted by manufactorer
for floor based fixing.
STEP 2 : Do the below installation for the cistern fixing.
* Place rubber seal into pan recess (Do not use sealant)
* Press Pan screw A into the pan screw hole.
* Use Nut B to tight pan screw A underneath the pan. (refer to Fig 1).
* Place cistern screw C into holes on the inside of cistern, making sure washers are
located correctly.
STEP 3:
* Align and push fully assembled toilet back
to wall, connecting pan spigot to pan collar.
Bucket flush and check for leaks. Due to the
design, weight and stability of the pan and
cistern, a silcone adhesive only is
recommended and excepted by manufactorer
for floor based fixing.
B. Nut
A. Pan ScrewC. Cistern screw
Stop Tap
Flexible
Hose
AB
CD
STEP 3:
Align and push fully assembled toilet back to wall, connecting
pan spigot to pan collar.
Bucket flush and check for leaks. Due to the design, weight
and stability of the pan and cistern, a silicon adhesive is
recommended for floor based fixing.
STEP 4:
Choose back inlet or bottom inlet

795
460
90
425
865
180
Ø100
380
155
130
605
440
355
355
Ø100
380
160
425
800
465
90
870
180
130
650
440
Casalino Rimless BTW Toilet Suite_8070
Casalino Compac BTW Toilet Suite_8090
505
555
15
20
430
15
20
425
795
460
90
425
865
180
Ø100
380
155
130
605
440
355
355
Ø100
380
160
425
800
465
90
870
180
130
650
440
Casalino Rimless BTW Toilet Suite_8070
Casalino Compac BTW Toilet Suite_8090
505
555
15
20
430
15
20
425
795
460
90
425
865
180
Ø100
380
155
130
605
440
355
355
Ø100
380
160
425
800
465
90
870
180
130
650
440
Casalino Rimless BTW Toilet Suite_8070
Casalino Compac BTW Toilet Suite_8090
505
555
15
20
430
15
20
425
STEP 5:
Gently lower cistern onto pan locating fixing screw into matching pan screw holes.
Rubber Seal
step 1: stick
the black
rubber seal to
the cistern
step 2: lower
the cistern
Figure 2
Figure 3
0800 728 662
[email protected]
www.newtech.co.nz
SPECIFICATIONS
NOTE: Before tightening fully, make sure cistern sits square and straight to the pan.
Casalino BTW Toilet Suite - 8070
Casalino Compac BTW Toilet Suite - 8090
795
460
90
425
865
180
Ø100
380
155
130
605
440
355
355
Ø100
380
160
425
800
465
90
870
180
130
650
440
Casalino Rimless BTW Toilet Suite_8070
Casalino Compac BTW Toilet Suite_8090
505
555
15
20
430
15
20
425