Nobis A13 V ZENITH User manual

EN - Installation, use and
maintenance manual
A13 V ZENITH
A13 C ZENITH
A13 V PLUS ZENITH

Dear Customer. Thank you for choosing a product from our range.
You are invited to read this manual carefully before using it, to
take full advantage of all its features, in complete safety.
This manual contains information necessary for correct installation,
start-up, use, cleaning and maintenance of the product.
Keep this manual in an appropriate place having carefully consulted it.
Improper installation, maintenance not carried out correctly and improper use of the product
relieve the manufacturer of any liability towards people or property.
All rights reserved. No part of this instructions manual can be reproduced or
transmitted with any electronic or mechanical device, including photocopying, recording or
any other saving system, for any proposals other than the exclusive use
by the purchaser’s staff, without express written permission from the manufacturer.

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
3
ENGLISH
MANUAL INDEX
1 Introduction 4
1.1 Symbols 4
1.2 Planned use 4
1.3 Improper use 4
1.4 Importance of the manual 4
1.5 General safety warnings 4
1.6 Legal warranty 5
1.7 Exclusions from the warranty 5
1.8 Spare parts 6
1.9 Identication plate 6
1.10 Disposal of the product 6
1.11 Hermetic product 6
2 Characteristics of the pellet 6
3 Installation 7
3.1 Air intake 7
3.2 Smoke channel and ttings 7
3.3 Chimney ue 8
3.4 Chimney pot 8
3.5 Hermetic product installation 8
3.6 Examples of correct installation 9
3.7 Documentation to issue 10
3.8 Product unpacking 10
3.9 Electrical connection 10
4 Maintenance 11
4.1 Smoke system maintenance 11
4.2 Product maintenance 11
5 Technical data of the product 11
5.1 Product data sheet 11
5.2 Technical features 11
5.3 Dimensions 12
5.4 Safe distances 12
6 Product conguration 12
6.1 Conguration of handheld device 12
6.2 Conguration of ext thermostat 13
6.3 Pellet loading 13
7 Description of remote commands 14
7.1 Description of receiver 14
7.2 Description of handheld device
keys 14
7.3 Description of handheld device
display 14
7.4 Flat battery signalling 15
7.5 Concise icons diagram 15
8 Menu browsing 16
9 First start-up instructions 16
9.1 Date and time setting 16
9.2 Calibration of handheld device
probe 16
9.3 User/auto management 17
9.4 Ambient temperature setting 17
9.5 Fireplace power setting 17
9.6 Switching on the product 17
10 The working phase 18
10.1 Saving mode 18
10.2 Air conditioning comfort
function 18
10.3 Powerful function 19
10.4 Ventilation management 20
11 Description of the menu functions 20
11.1 Thermostat with timer function 20
11.2 Auger loading function 21
11.3 Pellet/extraction mix 22
11.4 Stove status 22
11.5 Enabling external thermostat 23
11.6 Language 23
11.7 Contrast 23
11.8 FW version 24
11.9 Anticondensation 24
12 Duct channels 24
12.1 Setting single channel 24
12.2 Setting timer channel 25
12.3 Display channel status 25
12.4 Setting double channel 26
12.5 Setting timer channel 26
12.6 Display channel status 27
13 Phases concise diagram 27
14 Functions concise diagram 27
15 Signalling concise diagram 28
16 Anomalies concise diagram 28
17 Description of alarms 29
18 Cleaning the appliance 31
18.1 Cleaning the replace 31
18.2 Cleaning the glass door 32
18.3 Cleaning the ash pan 32
19 Wiring diagram 34

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
4
ENGLISH
1 INTRODUCTION
The product by Nobis was designed and manufactured
in compliance with the reference standards for the
manufacturing products (EN13240 wood stoves,
EN14785 pellet appliances, EN13229 replaces/
inserts for wood, EN12815 wood stoves), with
high quality materials. The products also comply
with the essential requirements of the Directive 2006/95/
EC
(Low Voltage) and the Directive 2004/108/EC
(Electromagnetic Compatibility).
The printing, translation and reproduction,
even partial, of this manual is intended
as binding by the manufacturer's authorisation and
the content of working logic and explanatory
gures is considered not be be disclosed.
Always consult the authorised technicians if in
doubt and/or confused by operation of the
the product.
The manufacturer reserves the right to make changes to
specications and technical and/or working features of
the product at any time without prior warning.
1.1 SYMBOLS
The following manual contains symbols which high-
light the importance of particular descriptions or con-
cepts;
INFORMATION: Compliance with the specications
guarantees correct operation of the product.
ATTENTION: Symbol used to identify
particularly important information
DANGER: The presence of this symbol
indicates utmost attention is required, to guarantee
user and product safety.
1.2 PLANNED USE
The product in this manual, is a
replace for domestic heating,
feed by automatic loading and exclusively with wood
pellets.
The product was designed and manufactured to work in
safety if the following conditions occur:
• installation by specialist staff
according to the specic reference standards;
• use within the limits declared on the product
data sheet and in this manual;
• compliance with technical procedures described in the
manual;
• carrying out routine maintenance within the times
and methods indicated in this manual;
• prompt execution of extraordinary
maintenance if necessary
(malfunctioning);
• activity and maintenance of safety devices
(do not remove or bypass this devices).
1.3 IMPROPER USE
The product must be intended for the use for which it
was expressly designed; for any other use, the manu-
facturer cannot
be held in any way liable for damage caused to
people, animals or property.
Improper use is intended as:
• use of the product as an incinerator;
• use of the product with fuel other than
wood pellets with a diameter of 6 mm;
• use of the product with liquid fuel;
• use of the product with the re door open and/or
glass broken and/or ash pan removed and/or
pellet tank open.
Any other use of the appliance other than that
planned must be authorised in advance
in writing by the manufacturer.
Furthermore, the manufacturer cannot be held in
any way liable for errors in installation, adjustment or
maintenance of
the product.
1.4 IMPORTANCE OF THE MANUAL
The manual has the purpose of providing essential
rules for correct installation, use and maintenance of
the product.
PRESERVATION: Keep the manual in a place that is
easy and quick to nd;
DETERIORATION OR LOSS: Consult the ofcial site to
download the manual;
PRODUCT TRANSFER: In the event of sale between pri-
vate individuals of the product, the owner is obliged
to
deliver the product with the following manual.
1.5 GENERAL SAFETY WARNINGS
Non-compliance with the provisions of this manual can
cause damage to people, animals and property.
• Installation, testing of the system, functionality
testing and initial calibration of the
product must only be carried out by
qualied and authorised staff.
• The product must be connected to a single chimney
ue that guarantees the draught declared by the
manufacturer and which complies with the installa-
tion
standards outlined in the assembly location of the
product.
• The premises where the product is installed must be
adequately ventilated (air intake).
• Do not touch the hot surfaces without adequate
protective equipment, to avoid burns.
• When in operation, the external surfaces
reach high temperatures.
• It is forbidden to make changes to the product unless
expressly communicated in writing by the
manufacturer.
• In the event of re in the chimney ue, contact
the Fire Brigade immediately.

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
5
ENGLISH ENGLISH
• The product can be used by children over
8 years of age and people with reduced
physical, sensor or mental capacity, or without
experience or the necessary know-how, provided
they are supervised, or have received
instructions on the safe use of
the appliance and have understood the dangers
involved. Children must not play with
the appliance.
• Cleaning and maintenance intended to be
carried out by the user must not be carried out
by children without supervision.
• Do not dry washing on the
the product.
• Fuel and ammable materials must be
kept a necessary distance from the product.
Danger of re.
• The product must be electrically connected
to a system equipped with a sufcient ground
system.
• In the event of a fault on the switch on system, do not
force switch on using ammable
materials and consult an authorised technician.
• Installation is forbidden in small rooms, bedrooms,
surroundings with explosive atmospheres, etc.
1.6 LEGAL WARRANTY
The user, to benet from the legal warranty,
must strictly comply with the provisions
indicated in this manual. In particular:
• always work within the use limitations of the product;
• always carry out routine maintenance;
• authorise people to use the machine with proven
capacity, attitudes and who are adequately trained
for the purpose;
• use original spare parts and specically
for the appliance model.
It is also necessary to provide a:
• scal receipt with the purchase date;
• a certicate of compliance issued for installation
by authorised staff.
Non-compliance with the provisions contained in this
manual will imply immediate
expiry of the warranty on the product and on
any spare parts assembled
later.
1.7 EXCLUSIONS FROM THE WARRANTY
The warranty excludes all malfunctions and/or dam-
age to the appliance resulting from the following
causes:
• damage caused by transport and/or movement;
• all parts resulting as being faulty due to
negligence or careless use, wrong
maintenance, non-conforming installation
with that specied by the manufacturer
(refer to the installation and use manual
supplied with the appliance);
• further damage caused by wrong intervention
by the user in an attempt to solve the
initial fault;
• aggravated damage caused by further use
of the appliance by the user once
the defect was noted;
• in the presence of a boiler, any corrosion,
scale or breakages caused by stray
current, condensate, abrasion or acidity in the
water, scale removal treatments carried out
improperly, no water, sludge or
limescale deposits;
• inefciency of the chimneys, chimney ues or parts of the
system on which the appliance depends;
• damage caused by tampering with the appliance,
atmospheric agents, natural disasters, vandalism,
electrical discharge, re, faulty
electrical and/or plumbing system.
The following are also excluded from the warranty:
• parts subject to normal wear such as gaskets,
glass, coverings and grates in cast iron, painted,
chrome-plated or gold-plated parts, handles and elec-
trical
cables, lights, switch on resistor, indicator lights,
knobs, all parts that can be removed from the
replace (e.g. refractory, brazier);
• colour variations of painted and ceramic parts,
as well as the ceramic cracks since they are
natural features of the material
and use of the product;
• masonry works;
• parts of the system (if present) not supplied by
the manufacturer;
Any technical intervention on the product
to eliminate the aforementioned defects or resulting
damage should therefore be agreed
with the Technical Support Centre, which
reserves the right to access or refuse the relevant job and
in any case they will not be carried out under
warranty, but rather Technical Support will provide the
possible conditions to specically agree upon
and according to rates in force for the works to carry out.
The user will also be responsible for the expenses which will
be necessary
to resolve any wrong technical intervention, tampering
or however damaging factors for the appliance
not attributable to the original defects.
Notwithstanding the restrictions imposed by legislation
and regulations,
every warranty to contain atmospheric and acoustic pol-
lution is also excluded.

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
6
ENGLISH
1.8 SPARE PARTS
Only use original spare parts.
Do not wait for the components to wear from use be-
fore replacing them.
This measure promotes prevention of accidents
caused by people, animals or property in the event
of product malfunctioning caused by faults.
You are advised to contact authorised staff to re-
place spare parts, worn parts and for extraordinary
maintenance of the the product.
1.9 IDENTIFICATION PLATE
The plate placed on the back of the product outlines
all the characteristic data of the appliance, includ-
ing the manufacturer's data, the serial number and
the CE marking.
1.10 PRODUCT DISPOSAL
Demolition and disposal of the product is the exclu-
sive responsibility of the owner, who should do so in
compliance with legislation in force in his
country on safety matters, with respect of and safe-
guarding the environment.
At the end of its useful life, the product must not be
disposed of as urban waste.
It can be delivered to specic differentiated waste
collection centres made available by municipal ad-
ministrations, or dealers who provide this service.
Disposal of the product as differentiated waste
means possible negative consequences for the envi-
ronment and health are avoided, deriving from
inadequate disposal. Furthermore, it allows
recovery of materials composing the product to
obtain important savings in energy and
resources.
1.11 HERMETIC PRODUCT
The products manufactured with a perfectly hermet-
ic
structure do not consume oxygen in the environ-
ment, since they take all the air from outside the
home (if correctly installed) and can therefore be
positioned inside all homes with a high level of insu-
lation, such as “passive houses” or “with high energy
efciency”. Thanks to this technology, there is no risk
of smoke emissions in the environment and no venti-
lation grates are necessary.
As a result, no cold air ows are created in the en-
vironment making it less comfortable and reducing
the overall efciency of the system. Hermetic prod-
ucts can also be installed in the presence of forced
ventilation or in premises which can go into negative
pressure compared to outside.
2CHARACTERISTICS OF THE PELLETS
Wood pellets are fuel made of pressed sawdust, of-
ten recovered from carpentry processing waste. The
material used cannot contain any foreign substance
such as glue, varnish or synthetic substances.
Sawdust, after drying and cleaning of impurities, it
is pressed using a matrix: due to the high pressure,
the sawdust heats activating the natural binders in
the wood; by doing so, the pellet maintains its shape
even without adding articial substances. The density
of wood pellets varies based on the type of wood
and can exceed 1.5 - 2 times that of natural wood.
The cylinders have a diameter of 6mm and a
variable length of 10 to 40mm.
Their density is equal to approx. 650 kg/m3. Due to
the low water content (< 10%), they have a high en-
ergy content.
The main quality certications for pellets on the Euro-
pean market today guarantee the fuel is within
class A1 in according to ISO 17225-2:2014 (formerly
EN 14961). Examples of these certications are for ex-
ample ENPlus, DINplus, Ö-Norm M7135, and guaran-
tee they comply in particular with the following char-
acteristics:
• heating power: 4.6 ÷ 5.3 kWh/kg;
• water content: ≤ 10% of weight;
• percentage of ash: max 1.2% of weight
(A1 under 0.7%);
• diameter: 6±1/8±1 mm;
• length: 3÷40 mm;
• content: 100% untreated wood without
any additional binder substances (percentage of
bark max 5%);
• packaging: in sacks made from
eco-compatible or
bio-degradable.
The manufacturer recommends, for its products, use
of class A1 certied fuel according to the standard En
ISO 17225-2:2014, or certied DIN PLUS (more restrictive
than class A1) or O-NORM M7135.
Pellets must be kept in a dry environment which is not
excessively cold. You are also advised to keep some
bags of pellets where the product is installed and op-
erating, to dry them of any humidity present.
Non-compliance with this aspect reduces the ther-
mal power of the fuel and means greater mainte-
nance must be done on the product.

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
7
ENGLISH ENGLISH
3 INSTALLATION
The assembly position must be chosen based
on the environment, the discharge and the chim-
ney ue. Check, with your local authority, if there are
more restrictive provisions regarding the oxidising air
intake, the smoke discharge system including the
chimney ue and chimney pot.
The manufacturer cannot be held in any way liable
in the event of installation non-compliant with legisla-
tion in force,
of incorrect premises air exchange or electrical con-
nection non-conforming with standards and/or inap-
propriate use of the appliance.
Installation must be carried out by a qualied techni-
cian, who will issue the purchaser with a Declaration
of Conformity for the system and will assume com-
plete responsibility for nal installation and resulting
good operation of the product.
In particular, he should ascertain:
• there is an adequate oxidising air intake and good
smoke discharge compliant with the type of prod-
uct installed;
• other stoves or devices installed do not cause
negative pressure in the room where the product is
installed (only for hermetic appliances, a maximum
of 15 Pa depression in the surroundings is permitted);
• when the product is on, there is no smoke back
draught in the surroundings;
• smoke evacuation is implement in total
safety (dimensioning, smoke seal, distances from
ammable materials..).
Once the position is decided where to install
the product, you need to pay attention:
• if the oor is made of combustible material,
you should use protection in suitable material (steel,
glass...) which also protects the front part from any
falling burning fuel during
cleaning operations:
• that the oor guarantees adequate
load capacity.
if the existing building does not meet this
requirement, you should take appropriate measures
(for example a load distribution plate).
3.1 AIR INTAKE
The installation premises of non-hermetic appliances
must be sufciently ventilated with specic openings,
with particular attention on the
position (they must NEVER be blocked), which consent
air reintegration in the environment.
The air must be taken directly from outside (not from
other rooms, garage, etc.) and must have a net useful
section equal or higher than 80
cm2pellet burning stoves and thermostoves (EN 14785)
and 100 cm2for boilers (EN 303-5).
The air intake is not necessary for
installation of the hermetic appliances that take air
directly from outside. Check and
comply with the ventilation requirements for simul-
taneous operations with other combustion devices
and in the presence of forced ventilation systems or
hoods (refer to section 6.4 of UNI 10683).
3.2 SMOKE CHANNEL AND FITTINGS
The term smoke channel indicates the piping con-
necting the appliance to combustion with the
chimney ue.
For heat generating appliances with an electric fan
to expel the smoke, the following installation instruc-
tions must be followed, provided by the manufactur-
er concerning the maximum length and number of
curves the smoke channels can have.
If no indications are given for maximum values or
deriving from preliminary calculations according
to UNI EN 13384-1, the following provisions must be
applied:
• comply with the product standard EN1856-2;
• the horizontal sections must have a minimum slope
of 3% upwards;
• the length of the horizontal section must be
minimal and its projection on plan must not ex-
ceed 4 metres;
• the number of changes of direction including
introduction in the chimney ue and excluding
that by effect of using a “T” element
in the appliances with rear smoke output, must
not exceed 3;
• the changes of direction must not have an angle
over 90°(45° curve recommended);
• the section must have a constant diameter
equal to the output of the replace up to the
tting in the chimney ue;
• it is forbidden to use exible metal and bre ce-
ment piping, furthermore the piping must guarantee
pressurised sealing;
• the smoke channels must not cross premises
in which installation is forbidden of combustion
appliances;
• Use watertight piping with silicone gaskets.
In any case, the smoke channels must be
sealed by combustion and condensate
products, as well as insulated if passing
inside the installation premises.
Assembly is not permitted of draught manual adjust-
ment devices on forced draught appliances.
You need to install a rst vertical smoke channel sec-
tion of at least 1 metre to guarantee correct smoke
ejection.
All local and national legislation and European
standards must be met when installing and using the
the product.

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
8
ENGLISH
3.3 CHIMNEY FLUE
When installing the chimney ue, the following provi-
sions must be applied.
• comply with the product standard EN 1856-1;
• it must be installed using materials suitable to
guarantee resistance to normal mechanical and
chemical stress, and have a correct insulation, to
avoid the formation of condensate, therefore it
must be hermetically insulated;
• have a mainly vertical state and
not be choked along its length;
• be correctly spaced using
air cavities and insulated from ammable
materials,
• the changes in direction must be
at most 2 and with an angle not exceeding 45°;
• the chimney ue inside the home must
however be insulated and can be inserted in
a cavity provided it complies with the relevant
piping standards;
• the smoke channel should be connected to the
chimney ue using a “T” joint with an inspectionable
collection chamber for collection of fuel residue
and, in particular, for condensate collection.
It is not possible to connect the appliance to a
chimney ue shared with other combustion appli-
ances or in the presence of hood exhausts.
It is forbidden to use direct wall discharge or
towards closed spaces or any other form of dis-
charge not planned by legislation in force in the
country of installation (In Italy, only roof discharge is
permitted)
3.4 CHIMNEY STACK
The standard UNI 10683 states the stack must meet
the following characteristics:
• the smoke outlet section must be at least
double the inner section of the chimney;
• shaped to prevent
water or snow penetration;
• be built in such a way that wind
cannot affect the smoke outlet
(wind-proof cap);
• the opening measurement, which is measured
between the lower coverage protective layer
and the lower point of the
smoke outlet section into the atmosphere, must be
outside the back draught area;
• Be built far from antennas or
satellite dishes and must never be used as a
support.
You are advised to check the safe distances which
must be complied with in the presence of
combustible materials and the type of insulating
material to use (data available directly on the
chimney ue plate)
3.5 HERMETIC PRODUCT INSTALLATION
In the event of installation of a hermetic product,
you can execute one of the following types of con-
nection with the piping:
• smoke discharge (1) and recovery of oxidising air
directly from outside (2)
2
1
1
2
21
• smoke discharge (1) and oxidising air channelling
(2) taking advantage of its coaxial discharge
to expel the smoke and pick
the air; therefore, installation is not necessary
of a grate to recirculate the air
inside the premises where the
the product.
For coaxial installation or air sampling directly from
the outside, it is recommended not to exceed
2.5 / 3 linear meters in order to ensure correct
oxygen supply to combustion.

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
9
ENGLISH ENGLISH
3.6 EXAMPLES OF CORRECT INSTALLATION
installation of the product (A) necessary for the hori-
zontal section for connection to an existing
chimney ue. Based on a slope of 3-5%, to reduce
ash deposit in the horizontal pipe section which must
not be over 3m (1). The existing chimney ue must
be inspectionable (2).
Installation of the product (B) requires an insulated
chimney ue (3) with an internal diameter of no less
than 100mm, since all the smoke piping was assem-
bled outside the home.
Installation of the product (C) requires a single wall
chimney ue (4) for the section inside the home.
Relating to the part placed in the attic, you are ad-
vised to install a chimney ue Ø120mm, with perfo-
ration for passage of the piping, extended to:
• minimum 100mm around the pipe if in contact
with inammable parts such as cement,
bricks, etc.;
• minimum 300mm around the pipe (or as
described in the plate data) if in contact with
ammable parts such as wood etc.
In both cases, insert adequate insulation (5) be-
tween the chimney ue and the attic.
You are advised to check and comply with the
plate data of the chimney ue, in particular the safe
distances from combustible materials.
The previous rules also apply for holes made on
walls.
On the lower part of the chimney ue, for all 3
installations, a “T” tting (6) was assembled with an
inspection plug (7), as well as on the inlet of the
chimney ue.
The upper part of the chimney ue, for all 3 installa-
tions, has a wind-proof chimney pot (8) assembled.
In the home, for all 3 installations, a grate is planned
to guarantee correct oxygenation of the premises
where the product is positioned.
Grate not necessary if appliance is hermetically
sealed.
It is not recommended to install a 90° curve as an in-
itial section which would quickly cause ash to block
smoke passage, causing draught problems
in the appliance.
9
67
7
A
1
2
3
3
4
5
8
8
8
6
9
9
6
7
In the event of particular atmospheric conditions
and/or hostile draught conditions, the product can
overcome these situations provided due installation
measures are in place, for example a wind-proof
chimney pot.
B
C
6

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
10
ENGLISH
3.7 DOCUMENTATION TO ISSUE
When installation is concluded, the installation tech-
nician must deliver to the user:
• the use and maintenance booklet of the appli-
ance supplied by the manufacturer;
• the technical documentation of the accessories
used and subject to maintenance;
• the documentation relevant to the evacuation
system of combustion products;
• The system booklet (where planned);
• the documentation certifying installation;
The useful documentation for installation liability
must include:
• a detailed description (also including photo-
graphs) of the presence of other heat generators;
• Declaration of Conformity of the system
to standard (M.D. 37/08);
• general description, or diagram or
photographic documentation of the changes
made to the system, if intervention was necessary
during installation;
• Use of certied material with the CE mark
(305/2011);
• possible instructions relating to the warranty;
• the date and signature of the installation techni-
cian;
NOBIS SRL cannot be held in any way liable in the
event of non-compliance with the installation and
start-up standards of its products.
3.9 ELECTRICAL CONNECTION
The product power supply cable must only be con-
nected after concluding installation and assembly
of the product, it must not be in contact with hot
parts and must remain accessible after installation.
To carry out electrical connection, proceed as de-
scribed below:
• connect the power supply cable on the back
of the appliance;
• connect the cable plug to the
current socket on the wall.
You can connect an outer thermostat with timer to
the appliance for its regulation or to switch on and
off. For connection and management of the “outer
thermostat” function, refer to the specic chapter
in the following pages of this
manual.
3.8 UNPACKING THE PRODUCT
Packaging is composed of box-
es in recyclable cardboard ac-
cording to the RESY standards
and wooden pallets. All pack-
aging materials can be re-used
for similar use or, if necessary, dis-
posed of as urban waste, in com-
pliance with legislation in force.
Remove the strap binding the
pallet to the packaging and lift
the cardboard; remove the plas-
tic bag around the product,
ensuring it is intact.
The body must always be
moved in a vertical position using
trolleys.
Pay particular attention
so that the door and its glass are
protected against mechanical
impact which would compro-
mise their integrity.
If possible, unpack the
product near the area where it
will be installed.
To remove the appliance from the pallet, you can
remove the two screws placed under the pallet (13
hex key) to release the appliance from the wooden
base.
Position the equipment and proceed with its
connection to the chimney ue. Find,
using the 4 adjustment feet, the right level so that
smoke discharge and the pipe are connected
correctly.

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
11
ENGLISH ENGLISH
4 MAINTENANCE
The maintenance operations, excluding routine
cleaning (explained in the relevant paragraph), must
be carried out by authorised, technical
staff. Remember, before carrying out any
maintenance operation, implement the following
precautions:
• all parts of the product must be “cold”;
• ensure there is no form whatsoever of
combustion (for example ash still hot);
• use of safety devices as per the directive;
• remove the plug from the electrical socket;
• having terminated maintenance, reset the prod-
uct paying attention to re-activate all the safety
devices.
4.1 SMOKE SYSTEM MAINTENANCE
The chimney ue must always be cleaned,
since deposits of soot or fuel residue reduce the
section blocking its draught, compromising good
operation of the product and, if in large quantities,
can catch re. It is compulsory to have a qualied
chimney sweep clean and check the chimney ue
and the stack at least once a year or after pro-
longed stoppage due to non-use of the appliance.
At the end of the control/maintenance, ask for a
report to be issued stating the system is safe.
Lack of cleaning prejudices safety
of the system.
It is compulsory for the system to be grounded and
have a differential switch in compliance with legis-
lation in force. Furthermore, ensure the socket is
compatible with the type of plug on the power
cable used.
4.2 PRODUCT MAINTENANCE
Carry out at least once a year or on each “Service
Hours” signalling (signal that appears on screen
when the working hours have been exceeded, over
which
excellent product operation is not guaranteed). In
this phase, the authorised technician should:
• completely and accurately clean the
smoke pipes;
• check the sealing status of all the gaskets;
• remove broken pellet residue inside
the pellet tank;
• re-assemble all parts of the appliance;
• check correct operation and good quality
combustion
5.1 PRODUCT DATA SHEET
5.2 TECHNICAL FEATURES
* this value can vary based on the type of energy
class of the home and the type of pellet used.
The data outlined are approximate and non-binding
and can vary based on the type of pellet
used. The manufacturer reserves the right
to make changes for the purpose of
improving product performance.
5TECHNICAL DATA OF THE PRODUCT
This chapter issues to the end user all the information
relating to the technical data of the product, the
dimensions, the installation measurements, the mini-
mum distance to comply with from walls
and furniture, sofas, etc.
PRODUCT DATA SHEET
EU 2015/1186
Brand Nobis
Model A13V - A13C ZENITH & A13V PLUS ZENITH
Energy efciency class A+
Direct thermal power (Kw) 13.2
Indirect thermal power (Kw) 11.8
Energy efciency index 127.3
Useful efciency (Nominal power %)
89.6
Useful efciency (Reduced power %)
92.4
Comply with the warnings and instructions for installation
and periodic maintenance of the instructions manual.
Model A13V - A13C ZENITH & A13V PLUS ZENITH
Reduced Nominal
Weight of appliance (kg) 176
Ø air inlet (mm) 60
Ø smoke outlet pipe (mm) 80
Vol. max. heating* (m3/h) 290
Power introduced (kW) 5.1 13.2
Yield introduced (kW) 4.7 11.8
Yield (%) 92.4 89.6
CO 13% O2 (%) 0.022 0.009
Tank capacity (kg) 22
Pellet hourly consumption (kg/h) 1.04 2.68
Autonomy (h) 21.2 8.2
Absorbed electrical power (W) 260
Electrical power supply (V-Hz) 230-50
Discharge gas ow (g/s) 4.89 7.60
Minimum draught (Pa) 10 10
Smoke temperature (°C) 102 192

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
12
ENGLISH
5.4 SAFE DISTANCES
Minimum distance from ammable mate-
rials
R Right hand side 400 mm
L Left hand side 400 mm
P Rear 150 mm
F Front 1000 mm
Floor saving platform
5.3 DIMENSIONS
TUTTI GLI SVILUPPI FORNITI IN FORMATO DXF SONO TEORICI . IL PARTICOLARE REALIZZATO DEVE ESSERE CONFORME AL DISEGNO 2D/3D
ALL FLAT PATTERNS PROVIDED IN DXF FORMAT ARE THEORETICAL . THE PIECE MUST BE IN COMPLIANCE WITH THE 2D/3D DRAWING
520
1210
540
60 60
80
60
265
532
128 128
230
388
166,5
364
Revisioni
Area Rev. Descrizione Data Approvata
1 RILASCIO PROGETTO 02/05/2019 R.A.
A A
B B
C C
D D
E E
F F
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
T
--
MATRICE (MATRIX)
(SUPPLIER CODE)
ASSIEME MODELLO
ZENITH-C
CODICE FORNITORE
-
1
N0014-SPAC-EU
- E.B. R.A. 02/05/2019
-
-
(DENOMINATION)
Proprietà della Società NOBIS S.r.l. Senza autorizzazione scritta della
stessa, il presente disegno non potrà essere utilizzato per la costruzione
dell’oggetto rappresentato né venire comunicato a terzi o riprodotto. La
Società proprietaria tutela i propri diritti a rigore di legge.
All proprietary rights reserved by NOBIS S.r.l. This drawing shall not be
reproduced or in any way utilized for the manufacture of the component of
unit herein illustrated and must not be released to other parties without
written consent. Any infringement will be legally pursued.
A3 1:10
DENOMINAZIONE
MATERIALE
DATA CONTR. PESO Kg.
TRATTAMENTO SUPERFICIALE (SURFACE TREATMENT)
DISEGNATORE
SCALA (SCALE) FORMATO (FORMAT)
STATO
(STATUS)
REVISIONE
(REVISION)
TOLLERANZE GENERALI SECONDO LA CLASSE UNI EN 22768-mK
GENERAL TOLERANCES AS PER UNI EN 22768-mK
NOBIS S.r.l.
N. DISEGNO
(MATERIAL)
(DESIGNER) (DATE)
(DRWG NR.)
(CHECKED) (WEIGHT)
Via Palazzolo,11 25037
Pontoglio - BS - Italy
P.iva e Cod. Fisc. 04222670160
S
MATERIA PRIMA (RAW MATERIAL)
L
P
F
R
TUTTI GLI SVILUPPI FORNITI IN FORMATO DXF SONO TEORICI . IL PARTICOLARE REALIZZATO DEVE ESSERE CONFORME AL DISEGNO 2D/3D
ALL FLAT PATTERNS PROVIDED IN DXF FORMAT ARE THEORETICAL . THE PIECE MUST BE IN COMPLIANCE WITH THE 2D/3D DRAWING
520
1210
540
60 60
80
60
265
532
128 128
230
388
166,5
364
Revisioni
Area Rev. Descrizione Data Approvata
1 RILASCIO PROGETTO 02/05/2019 R.A.
A A
B B
C C
D D
E E
F F
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
T
--
MATRICE (MATRIX)
(SUPPLIER CODE)
ASSIEME MODELLO
ZENITH-C
CODICE FORNITORE
-
1
N0014-SPAC-EU
- E.B. R.A. 02/05/2019
-
-
(DENOMINATION)
Proprietà della Società NOBIS S.r.l. Senza autorizzazione scritta della
stessa, il presente disegno non potrà essere utilizzato per la costruzione
dell’oggetto rappresentato né venire comunicato a terzi o riprodotto. La
Società proprietaria tutela i propri diritti a rigore di legge.
All proprietary rights reserved by NOBIS S.r.l. This drawing shall not be
reproduced or in any way utilized for the manufacture of the component of
unit herein illustrated and must not be released to other parties without
written consent. Any infringement will be legally pursued.
A3 1:10
DENOMINAZIONE
MATERIALE
DATA CONTR. PESO Kg.
TRATTAMENTO SUPERFICIALE (SURFACE TREATMENT)
DISEGNATORE
SCALA (SCALE) FORMATO (FORMAT)
STATO
(STATUS)
REVISIONE
(REVISION)
TOLLERANZE GENERALI SECONDO LA CLASSE UNI EN 22768-mK
GENERAL TOLERANCES AS PER UNI EN 22768-mK
NOBIS S.r.l.
N. DISEGNO
(MATERIAL)
(DESIGNER) (DATE)
(DRWG NR.)
(CHECKED) (WEIGHT)
Via Palazzolo,11 25037
Pontoglio - BS - Italy
P.iva e Cod. Fisc. 04222670160
S
MATERIA PRIMA (RAW MATERIAL)
Ø 60 channelling
Ø 60 channelling
Ø 80 smoke
discharge
Ø 60 air
inlet
6 PRODUCT CONFIGURATION
Once all the installation, covering assembly (where
present as a kit) and electrical connection are in
place, with utmost attention, access the rear part of
the product to power it.
The “I/O” switch in the gure above must be
positioned on “I”. In the event of a power failure,
check the condition of the fuse placed under the
switch (4A fuse EU conguration). During periods of
non-use, you are advised to disconnect the cable
powering the appliance, and also the batteries from
the handheld device.
6.1 CONFIGURATION OF HANDHELD DEVICE
Remove the protective cover of the batteries on the
rear of the remote control, as in the gure , and
insert 3 batteries (type AAA Alkaline 1.5V)
in the handheld device compartment, paying
attention to polarity. Close the protective cover of
the batteries as in the gure B.
A
EMERGENCY PANEL
B
A
B
A
AB
The batteries, once exhausted, must be disposed of
in the dedicated collection centers.
To protect the battery from adverse conditions or
misuse, remember to:
- keep the command away from heat sources, risk
of explosion;
- remove the batteries in case of prolonged not use
of command, risk of oxidation and liquid leakage;
Nobis srl declares that the type of “Handheld” radio
device complies with Directive 2014/53 / EU.
The full text of the EU declaration of conformity is
available at the following Internet address:
https://www.nobisre.it/wp-content/uploads/2019/04/DoC-Palmare-Radio-Nobis-1.pdf
The handheld device, after a rst short screen
with the manufacturer’s logo, lists a series of
languages available on the menu.
CAUTION
Risk of
explosion if battery
is replaced with
the wrong type.
ALKALINE
ALKALINE
ALKALINE

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
13
ENGLISH ENGLISH
Select the language, using the keys that you
want to use as the display standard. Press the key
to conrm and go to the next screen.
To work correctly, the handheld device
requires interfacing with the electronic board inside
the product. For this reason, the display shows a rst
installation message.
If rst use of the handheld device, choose YES with
the selection keys .Press the key to conrm
and go to the next screen.
Follow the guide instructions to link via remote the
appliance to the display, as outlined in the gure
below.
Keep the remote communication key of the
electronic board pressed for a few seconds, placed
on the rear of the product, to
start the unit search procedure.
The yellow, ashing led, under the icon indicates
the electronic board is waiting to
receive the handheld device signal.
Pressing the conrm key on the handheld de-
vice, the components can communicate with one
another.
A tick sign on the display, accompanied by an
acoustic signal, indicates the remote connection
operation has successfully concluded.
If the batteries are replaced, you don’t necessarily
have to follow the initialisation procedure of the
handheld device. In this case, when the display
shows the message “FIRST INSTALLATION?”,
select NO and press the conrm
key.
OK
OK
OK
OK
6.3 PELLET LOADING
Fuel is loaded by inserting pellets from the upper part
of the product, opening the door. Ensure the content
of the bag of pellets does not fall around the edges
of the tank,
paying particular attention to centring,
during the loading phase. Also avoid the pellet
packaging coming in contact with hot surfaces.
Ensure you correctly close the cover of the tank
again after loading the pellets. Closure is controlled
by an electronic contact (for the models where
planned). In the event of non-closure, a sign
warns the user to pay attention
to tightening, before passing to alarm mode, in the
event the warning is ignored.
6.2 CONFIGURATION OF T.EXT THERMOSTAT
If you want to manage the appliance from a differ-
ent room (in that specic room, the remote handheld
device cannot communicate), you can connect an
external thermostat to the product, to allow modula-
tion of combustion or, by activating a particular func-
tion, allow switch on or off of the product. As in the
gure below, connect the terminals of the thermo-
stat to the terminal board on the back of the product
(near the emergency panel).
TERMINAL
EXTERNAL THERMOSTAT
Following electrical connection, to allow the control
unit to recognise the presence of the t.ext, the rec-
ognition function must be enabled from the SETTINGS
menu (see the “ENABLE EXTERNAL THERMOSTAT” par-
agraph)
By enabling the function that allows external thermo-
stat enabling, on the handheld device reading and
management of the ambient temperature are inhib-
ited. The handheld device displays TON if required,
TOFF if the temperature set on T.ext is reached.

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
14
ENGLISH
7.2 DESCRIPTION OF HANDHELD DEVICE KEYS
The handheld device is presented as in the image
below:
1Increase key (selection key)
2Decrease key (selection key)
3ON/OFF or reset from “Sleep” mode key
4Display
5MENU access and conrm key
6Back to previous screen key
In “Sleep” mode, the screen of the handheld device
is blacked out, only maintaining enabled, if neces-
sary, the remote communication with the
appliance, to reduce battery consumption.
7.3
DESCRIPTION OF THE HANDHELD DEVICE DISPLAY
The handheld device display is as follows:
After 20 seconds of inactivity, the display on the
handheld device blacks out and passes to “SLEEP”
mode, maintaining the remote connection with the
appliance. The display re-enables only by pressing
the key.
STAND-BY SCREEN
Before connection using the emergency cable, re-
move the batteries from the handheld device
from the specic compartment. DANGER OF FIRE
1
2
3
4
5
6
1
2
3
7DESCRIPTION OF REMOTE CONTROL
Before switching on the appliance, you are advised
to read the following chapter carefully relating to
use of the receiver and the handheld device,
as well as their related functions.
INFORMATIVE NOTE:
• frequency bands and transmitted power used by
the equipment as reported in technical
documentation: 868.3MHz - 869.85MHz
• frequency bands and respective power limits
transmitted applicable to the device (frequencies
and standardized powers): 6dBm ERP
7.1 DESCRIPTION OF RECEIVER
The appliance is equipped with an emergency re-
mote board, placed at the back of it, which allows
basic management of the functions in the event the
handheld device is faulty or not working properly.
1 Serial connection (use by authorised staff ONLY)
2 USB connection (use by authorised staff ONLY)
3 Emergency cable connection
4 GREEN LED - appliance working status
5 YELLOW LED - remote communication in progress
6 RED LED - alarm on
7 BLUE LED - System updating in progress
8 Appliance switch on/off button
9 Receiver handheld device remote combination
button
10 Manual upgrade button
(use by authorised staff ONLY)
In the event of malfunctioning of the remote com-
munication between the handheld device and the
receiver, or if the batteries are at, use the emer-
gency cablesupplied, to restore communication
between the remote devices.
1 3
24 5 67 8 9 10
EMERGENCY CA-
BLE CONNECTION
3

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
15
ENGLISH ENGLISH
Displays the ambient temperature detected by the
handheld device. Furthermore, pressing the scroll key
allows display of the temperature setting, which
can be edited using the two scroll keys .
Conrmation of each variation takes place
automatically within 3 seconds of editing the data,
or by pressing the conrm key . An acoustic signal
conrms the change
was made.
Indicates the work power set. Furthermore, by
pressing the scroll key , it allows the power setting
to be displayed, which can be edited using the two
scroll keys .
Conrmation of each variation takes place
automatically within 3 seconds of editing the data,
or by pressing the conrm key. An acoustic signal
conrms the change
was made.
Icon indicating the status of the appliance
(see “Concise icons diagram”).
7.4 FLAT BATTERIES SIGNAL
If batteries are at, the display presents a symbol
which indicates their limit status,
however maintaining the functions enabled of the
handheld device.
As soon as the level of the batteries does not allow
any remote communication, the handheld device
displays, on the full screen, the image of the at bat-
tery, blocking all the functions connected to it until
the batteries are replaced.
OK
OK
MEANING
SWITCH ON
WORK
WORK WITHOUT TEMPERATURE
CONTROL
SAVING
AUTO WORK
(see specic paragraph)
POWERFUL WORK
(see specic paragraph)
OPTIMISED WORK
(see specic paragraph)
BRAZIER CLEANING
(where present)
CLEANER ON (cleaning to
empty brazier)
AIR CON. COMFORT ON
RESTART FROM
AIR CON. COMFORT
FINAL CLEANING
OFF
SIGNAL WARNING
(see specic paragraph)
FLAME TEMPERATURE
OVER LIMIT
EXCESS PELLET LOADING
PRESSURE SENSOR FAULT
FLAM READING PROBE FAULTY
HANDHELD BATTERIES
ALMOST FLAT
REACHED LIMIT
SERVICE HOURS
7.5 ICONS CONCISE DIAGRAM
1
2
3
1 2 3

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
16
ENGLISH
8 MENU BROWSING
To access the menu, press the key on the stand-
by screen to display the selection items,
as in the gure.
Scroll the menu items using the keys
Conrm the selection with the key
To return to the previous item, key
A practical example follows of how to execute navi-
gation using all the selection keys.
OK
OK
9FIRST START-UP INSTRUCTIONS
This chapter highlights a series of operations to carry
out during the rst start-up phase
of the appliance.
9.1 DATE AND TIME SETTING
The procedure follows to set the date and time, use-
ful for the thermostat with timer function, on the mod-
els of the manufacturer's range.
OPERATING PROCEDURE:
MENU >> SET USER >> SETTINGS >> TIME - DATE
Access the menu by pressing key
Scroll the items to SET USER with the key
Access the menu by pressing key
Scroll the items to SETTINGS with the key
Access the menu by pressing key
Scroll the items to TIME-DATE with the key
On the TIME - DATE menu item, key
The screen appears to adjust the time and calendar
as in the gure below.
OK
OK
OK
OK
Edit the data highlighted using the keys
Conrm the data changed using the key
Repeat the operation to complete the settings.
During editing, remember that:
• to return to the previous data, without saving
the last data changed, press the key
• if you intend changing a single datum, having ter-
minated the change, press the key multiple times
until you exit the function described in the paragraph.
To return to the STAND-BY screen, use the
key , repeating the operation multiple times.
OK
OK
9.2
AMBIENT PROBE CALIBRATION (HANDHELD DEVICE)
The procedure follows to calibrate the handheld de-
vice probe, if the value should differ from reading
a reference sample thermostat.
OPERATING PROCEDURE:
MENU >> SET USER >> SETTINGS >> CAL. AMB.P.
Access the menu by pressing key
Scroll the items to SET USER with the key
Access the menu by pressing key
OK
OK
+
+
+
+

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
17
ENGLISH ENGLISH
Scroll the items to SETTINGS with the key
Access the menu by pressing key
Scroll the items to CAL. P.AMBIENT, key
On the CAL. P.AMBIENT menu item, key
The screen appears to adjust the ambient probe, as
in the gure below.
OK
OK
Edit the data highlighted using the keys
Example: Reference thermostat displays 21°C and
handheld device displays 19°C.
Set +2 for the handheld device to display the value
21°C.
Conrm the data changed using the key
To return to the STAND-BY screen, use the
key , repeating the operation multiple times.
OK
9.3 USER / AUTO MANAGEMENT
The logic, relating to this type of management, is as
follows:
USER: the user reserves the right to
set the ambient temperature he or she
wants and the power to the replace useful
to reach this temperature.
AUTO: the user simply sets
the ambient temperature he or she
wants for best comfort, the appliance
manages the power to the replace and
ventilation (if present and enabled)
autonomously.
OPERATING PROCEDURE:
MENU >> ENABLE AUTO
Access the menu by pressing key
The rst item on the menu, ENABLE AUTO.
Tick using the key if you intend managing the
appliance in AUTO mode .
Do not tick if you want to work in
USER mode .
OK
OK
This setting inhibits manual management of the op-
tional fan, with the exception of
the fan setting on OFF. In this case, the appliance
autonomously only manages power to the replace.
Ventilation remains
disabled.
9.5 FIREPLACE POWER SETTING
The replace power denes the quantity of heat pro-
duced by the appliance, this implies
a different fuel consumption. Basically, it is used to
speed up the useful time to reach the
ideal temperature, set for the premises where the
product is installed.
From the STAND-BY screen, key to select the
power;
The values vary from 1 to 7;
Edit the value with the keys
Conrm the new setting with the key or wait 3
seconds for auto-conrm.
OK
9.4 AMBIENT TEMPERATURE SETTING
The ambient temperature denes the temperature
you want to obtain in the premises where the prod-
uct is installed.
From the STAND-BY screen, key to select the
value;
The values vary from 7°C to MAN (with the MAN val-
ue it is intended that, once set, the appliance NEVER
goes to power save).
Edit the value with the keys
Conrm the new setting with the key or wait 3
seconds for auto-conrm.
OK
9.6 SWITCHING ON/OFF THE PRODUCT
To switch on the product, prolonged press the key
until the following screen appears,
followed by an acoustic signal.
This screen remains on for the following machine sta-
tuses;
SWITCH ON • Initial phase of pellet loading;
WAITING FLAME • Flame development waiting
phase;
FLAME PHASE • Stabilisation phase of ame and
oxidiser inside the brazier;
1
2
1 2

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
18
ENGLISH
The appearance is highlighted of the “ame” sym-
bol with the writing ON, without displaying the work
power.
Prolonged pressing of the key accompanied by
acoustic signalling causes switching off of the prod-
uct, as well as resetting of any alarms.
For models with an automatic cleaner, during
the switch on phase, the product activates a brazier
cleaning phase before passing to SWITCH ON.
In the event of FAILED IGNITION, after pressing the
button, a POP UP signals the need to suck the pellet
from the brazier before turning the appliance back
on, thus avoiding discharge of unburned pellets into
the ash drawer.
10 THE WORKING PHASE
The products in the range include a working phase
with 7 operating power levels. The behaviour of the
appliance is described below once the setting, if set,
is reached of the ambient temperature.
10.1 SAVING MODE
During the work phase, the appliance works with the
objective of reaching the ambient temperature
set; when this condition is met, power is reduced to
SAVING mode, the phase in which fuel consumption
is minimal.
At this point, you must execute a series of precisions
to benet the AUTO function, to pass to saving and/
or return to fully operational mode:
• Ventilation, if present and enabled, works in
different operational modes based on the existing
discrepancy between the setting and the tempera-
ture in the premises.
• The appliance gradually increases the
power to the replace, as soon as the temperature
in the premises goes under the required
setting (optimisation of combustion and
acoustic comfort).
During rst start-up of the product, unpleasant
odours may occur or smoke caused by evaporation
or drying of certain materials used. This phenomena
disappears after some hours of use. During this peri-
od, you are advised to keep the premises well ven-
tilated.
Screen in SAVING mode:
10.2 AIR CON. COMFORT FUNCTION
As described in the “saving mode” paragraph, the
appliance has the objective of meeting the comfort-
able heating requirements of the user. The function
which can be enabled, linked to his mode, also en-
sures, if the home has a good energy class, a fuel
saving through intelligent switch off of the product
(reaching or required of the desired setting).
The procedure follows to enable the
function, the change of values with relevant
meaning, a practical example of setting.
OPERATING PROCEDURE:
MENU >> SET USER >> AIR CON. COMFORT
Access the menu by pressing key
Scroll the items to SET USER with the key
Access the menu by pressing key
Scroll the items to AIR CON. COMFORT, key
On the AIR CON. COMFORT menu item, key
The screen appears with activation of the
function and adjustment of the setting parameters,
as in the gure.
OK
OK
OK
Enable/disable the function with the key to dis-
play the addition or bypassing of the tick and:
• Return to SETUSER with the key .
OR
• Pass, using the key , to the choice of
time in saving mode, before the function
switches off the product.
Edit the value with the keys
OK
Conrm the data with the key and go to
temperature setting, under which the product must
switch on.
OK
Always vacuum the brazier using an ash cleaner,
risk of re.

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
19
ENGLISH ENGLISH
STATUS SCREEN.
To recognise switch off of the appliance in AIR CON.
COMFORT condition, the screen must be dis-
played.
To recognise the appliance is about to switch on in
the AIR CON. COMFORT condition, the screen
must be displayed.
PRACTICAL EXAMPLE:
Ambient setting at 21°C;
Saving mode setting at 3 minutes;
Restart °C setting at -2°C compared to
setting.
The appliance switches off as soon as the
temperature in the home reaches the value
set + 3 minutes in saving mode.
The product switches on when a temperature is de-
tected of 18°C (21°C - 2°C - 0.5°C tolerance).
You can also activate the function using an external
thermostat, taking into consideration that this does
not include the hysteresis values.
You are advised to use an external thermostat with
its hysteresis value settable up to a
maximum of 3°C. Operation of the appliance could
start the switch on and off phase many times during
the day;
this could compromise the duration of
switch on resistance.
Conrm the data changed using the key
and return to the SET USER screen.
In saving mode, when changing the time and restart
degrees, remember that:
• to return to the previous data, without saving
the last data changed, press the key
• if you intend changing a single datum, having ter
minated the change, press the key multiple
times until you exit the function described in the
paragraph.
To return to the STAND-BY screen, use the
key , repeating the operation multiple times.
OK
OK
Edit the value with the keys
The logic, relating to this type of management, is as
follows:
USER: the user reserves the right to
set the ambient temperature he or she
wants and the power to the replace useful
to reach this temperature.
POWERFUL: the end user manually activates the
function or using the settable
time slot. The appliance
is released from the power set,
also forcing ventilation at the maximum
speed, for 5 minutes or up to
when the setting is reached, or
if the time slot or the user
disables the function.
10.3 POWERFUL FUNCTION
The function described in the paragraph, once acti-
vated, allows heating of the ambient, taking advan-
tage of the maximum speed of the fan.
The scope is to supply the maximum heat to the det-
riment of a minor acoustic comfort.
In this respect, the possibility exists of adjusting
the time slot for operation of the POWERFUL function.
With the POWERFUL function enabled and ventila-
tion disabled (for models that include the optional
ventilation), the fan activates autonomously
at maximum speed for the activity time
of the function.
OPERATING PROCEDURE 1:
MENU >> ENABLE POWERFUL
Access the menu by pressing key
Scroll the items to ENABLE POWERFUL, key
Pressing the key , the POWERFUL screen appears
with the type of setting you want to activate.
OK
OK
As previously described, you can set a time slot to
enable the function. Below, the operating procedure
is displayed to access and edit the data.
Edit the type of activation with the keys
OFF - Powerful disabled;
ON - Powerful enabled;
TIMER - Powerful enabled with time slot.
1
2
1 2

Use and Maintenance Manual model “A13V - C ZENITH & A13 V PLUS ZENITH”
20
ENGLISH
10.4 VENTILATION MANAGEMENT (if optional)
The products of the range with optional ventilation,
taking advantage of the natural convection system
which guarantees a considerable amount of heat in
the ambient, in total absence of noise. However,
the possibility exists, by accessing the menu outlined
below, to enable optional ventilation according to
the desired power.
OPERATING PROCEDURE:
MENU >> SET USER >> VENTILATION
Access the menu by pressing key
Scroll the items to SET USER with the key
Access the menu by pressing key
First item in the “VENTILATION” menu, key
The screen appears with adjustment of
ventilation as in the gure below.
OK
OK
OK
OK
Conrm with key
To return to the STAND-BY screen, use the
key , repeating the operation multiple times.
Edit the ventilation power, keys
0 - ventilation disabled;
1-7 - ventilation setting range;
PS - ventilation follows power to the replace
set on the appliance.
If the PS function is not set, the fan
is always restricted by the power of
the product.
11
DESCRIPTION OF THE MENU FUNCTIONS
This chapter describes the user menu functions, useful
to improve some comfort related aspects of the user
and/or operation of the product.
11.1 THERMOSTAT WITH TIMER FUNCTION
With the Thermostat with timer function, you can:
program for each day of the week automatic switch
on and off of the product, with 4 independent time
intervals (PROGRAM 1 - 2 - 3 - 4).
The steps are outlined below to follow, starting with
the STAND-BY screen, to access the relevant menu.
OPERATING PROCEDURE 2:
MENU >> SET USER >> SETTINGS >> POWERFUL
Access the menu by pressing key
Scroll the items to SET USER, key
Access the menu by pressing key
Scroll the items to SETTINGS with the key
Access the menu by pressing key
Scroll the items to POWERFUL with the key
On the POWERFUL menu item, key
The screen appears with adjustment of the
setting parameters, as in the gure below.
OK
OK
OK
OK
Edit the switch on and switch off times, as well as
enabling the days of the week, keys
During editing, remember that:
• to return to the previous data, without saving
the last data changed, press the key
• if you intend changing a single datum, having ter
minated the change, press the key multiple
times until you exit the function described in the
paragraph.
To return to the STAND-BY screen, use the
key , repeating the operation multiple times.
OK
If the time slot is set with the POWERFUL function, the
data setting in “Enable Powerful” must be “TIMER”. If
the value is set to "ON”, the time slot is inhibited up to
its disabling (OFF).
The POWERFUL function, if both the time slot and the
manual tick are enabled, inhibits AUTO manage-
ment up to its disabling.
Conrm each data change using the key until
you exit the SETTINGS screen.
OK