Nordyne 072C-16 User manual

Installation Instructions
Do not store or use gasoline
or other flammable vapors
and liquids in the vicinity of
this or any other appliance.
DO NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
FOR YOUR SAFETY
WARNING:
Improper installation,
adjustment, alteration,
service, or maintenance can
cause injury or property
damage. Refer to this
manual. For assistance or
additional information
consult a qualified installer,
service agency, or the gas
supplier.
These instructions are primarily intended to assist qualified individuals experienced in the proper installation of this
appliance. Some local codes require licensed installation/service personnel for this type of equipment. Read all
instructions carefully before starting the installation.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any
appliance.
• Do not touch any electrical
switch; do not use any
phone in your building.
• Immediately call your gas
supplier from a neighbor's
phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas
supplier, call the fire
department.
• Extinguish any open flame.
80+ High Efficiency Upflow/Horizontal and Downflow
with Variable Speed Blower
Residential Gas Furnaces
!
*RK 80+ Downflow
*RA 80+ Upflow

Table of Contents
Furnace Specifications ....................................................................................................................................................... 4-5
Unit Dimensions and Shipping Weights ....................................................................................................... 4-5
Capacities-Furnace Airflow Data ..................................................................................................................... 6
Safety Information ............................................................................................................................................ 7
Installation Requirements ..................................................................................................................................................... 7
Requirements and Codes ................................................................................................................................ 7
Location............................................................................................................................................................ 7
Clearances to Combustibles ........................................................................................................................... 7
Venting and Combustion Air Requirements ................................................................................................................... 8-13
General ............................................................................................................................................................ 8
Installation in an Unconfined Space ................................................................................................................ 8
Installation in a Confined Space ...................................................................................................................... 8
Horizontal Furnace Installation ........................................................................................................... 10
Air From Inside .................................................................................................................................... 11
Outdoor Air Using Vertical Ducts ........................................................................................................ 12
Air Directly Through an Exterior Wall ................................................................................................. 12
Outdoor Air Using A Crawl Space and Ventilated Attic ...................................................................... 12
Outdoor Air Through Horizontal Ducts ............................................................................................... 12
Venting Requirements .................................................................................................................................................... 13-19
General .......................................................................................................................................................... 13
Category I - Common Venting ....................................................................................................................... 13
Category III - Horizontal Venting .................................................................................................................... 15
Horizontal Venting for Upflow Models ................................................................................................ 15
Horizontal Power Venting ................................................................................................................... 17
Location of Outdoor Terminations ................................................................................................................. 17
Horizontal Installation ......................................................................................................................... 17
Flexible Vent Systems .................................................................................................................................... 19
Circulating Air Supply ..................................................................................................................................................... 19-20
General .......................................................................................................................................................... 19
Return Air ....................................................................................................................................................... 19
Gas Supply and Piping .................................................................................................................................................... 20-22
General .......................................................................................................................................................... 20
Leak Check .................................................................................................................................................... 21
Conversion ..................................................................................................................................................... 21
High-Altitude Application ............................................................................................................................... 21
Natural Gas High Altitude Conversion .......................................................................................................... 22
LP/Propane Gas Sea Level and High Altitude Conversion .......................................................................... 22
Electrical Wiring .............................................................................................................................................................. 22-24
General .......................................................................................................................................................... 22
Line Voltage Wiring ........................................................................................................................................ 23
Low Voltage Wiring ........................................................................................................................................ 24
Start-up & Adjustments ....................................................................................................................................................... 24
General .......................................................................................................................................................... 24
Start-Up Procedures ...................................................................................................................................... 24
Verifying and Adjusting Firing Rate ............................................................................................................... 24
Configuring the Blower .................................................................................................................................. 25
Selecting Airflow ............................................................................................................................................ 25
Verifying and Adjusting Temperature Rise .................................................................................................... 26
Verifying Burner Operation ............................................................................................................................ 27
Verifying Operation of Supply Air Limit Switch .............................................................................................. 27
Description of Components ................................................................................................................................................ 28
Wiring Diagram ..................................................................................................................................................................... 30
Maintenance .................................................................................................................................................................... 29-31
Vent System ................................................................................................................................................... 29
Air Filter(s) ...................................................................................................................................................... 29
Lubrication ..................................................................................................................................................... 29
Blower Compartment ..................................................................................................................................... 29
Heat Exchanger and Burner Maintenance .................................................................................................... 29
Cleaning of Flue Passages ............................................................................................................................ 31
Installation/Performance Checklist .................................................................................................................... Back Cover

4
Unit Shown in Upflow
Position Rotate 90˚
Clockwise or Counter
Clockwise for Horizontal
Application
23 3/4
19 3/4
3/4
43
25 1/8
25 1/425 5/8
23
27 5/8
15 20 1/2
251/4
33
301/4
A
B
C
FLUE
OUTLET
11/2 X 31/2 Cut-out for
Gas Connection
3/4 3/4
1
1/4
3/4
7/8 Cut-out for Electric
Connection
11/2 X 31/2 Cut-out for
Gas Connection
7/8 Cut-out for
Electric Connection
Return
Air Opening
(Side)
1 1/4 1 1/4D 23
Return Air Opening
(Bottom)
7/8
FURNACE SPECIFICATIONS - Upflow/Horizontal Models
Figure 1a. Upflow Unit Dimensions
Table 1a. Upflow Furnace Dimensions and Shipping Weights
Furnace Dimensions Shipping
Model Input A B C Flue Outlet Weight D
*RA (Btuh) (in.) (in.) (in.) (in.) (lbs) (IN.)
072C-16 72,000 19 3/4 18 1/4 3 3/4 4 152 17 1/4
096C-12 96,000 19 3/4 18 1/4 3 3/4 4 163 17 1/4
096C-16 96,000 19 3/4 18 1/4 3 3/4 4 163 17 1/4
096C-20 96,000 22 1/2 21 3 3/4 4 174 20
120C-16 120,000 19 3/4 18 1/4 3 3/4 4 174 17 1/4
120C-20 120,000 22 1/2 21 3 3/4 4 182 20
144C-20 144,000 22 1/2 21 4 1/4 5 194 20
FURNACE DIMENSIONS AND
SHIPPING WEIGHTS

5
FURNACE SPECIFICATIONS - Downflow Models
Figure 1B. Downflow Unit Dimensions
Cut-out for Electric
Connection
Both sides
Cut-out for Gas Connection
1-1/2 x 3-1/2 (both sides)
27 7/8"
3/4"
23 5/8"
19 3/4" 3/4"
C
C
L
3/4"
3/4"
43"
4" Dia. Vent
Cut - out for
Gas Connection
A
B
B
25"
15 1/2"
27 1/8"
25"
3/4"
C
L
(Bottom Opening)
(Bottom Opening)
10 1/4"
24 1/2"
19 3/4"
Table 1B. Downflow Furnace Dimensions and Shipping Weights
Model Furnace Shipping
Number Input A B C Weights
*RK (Btuh) inches inches inches (lbs)
060C-12 60,000 14 1/4 12 3/4 5 1/2 134
072C-12 72,000 14 1/4 12 3/4 5 1/2 135
072C-16 72,000 19 3/4 18 1/4 11 147
096C-12 96,000 19 3/4 18 1/4 11 154
096C-16 96,000 19 3/4 18 1/4 11 156
120C-20 120,000 19 3/4 18 1/4 11 182
DOWNFLOW FURNACE MODELS
FURNACE DIMENSIONS AND
SHIPPING WEIGHTS
D ime nsions

6
CAPACITIES —Furnace Airflow Data
720 900 1056 1200 1350 1500 1656 1800
7 1 0 1 0 1 0 1 0
6 0 0 0 0 1 1 1 1
5 0 0 1 1 0 0 1 1
72,000 59 51 44
90,000 63 55 49 44
96,000 67 59 53 47
108,000 67 59 53 48
120,000 66 59 54 49
126,000 69 62 56 51
144,000 71 64 59
80,000 67 59 52 47
100,000 73 65 59 53 49
120,000 71 64 59
Temperature Rise °F (Recommended settings are Bold)
Nominal Air-Flo
w
80+%92+%
Switches
Table 2. Heating Airflow Settings
NOTE: 0 = OFF 1 = ON
Nominal A/C and HP
LOW HIGH 1 2 3 4
567
Capacity
500 720 0 0 0 1
550 800 0 0 0 0
610 880 0 0 1 0
650 945 1 0 0 1
72010501000
80011551010
90013050101
1000 1450 0 1 0 0
1060 1530 1 1 0 1
1100 1595 0 1 1 0
1170 1700 1 1 0 0
1290 1870 1 1 1 0
CFM SWITCH NUMBER
2 TON
3.5 TON
4 TON
5 TON
3 TON
2.5 TON
Table 1. Cooling/Heat Pump Airflow Settings
NOTE: 0 = OFF 1 = ON
Notes:
1. Recommended temperature rises are highlighted in bold.
2. Airflow rates of 1800 CFM or more require two return air connections. Data is for operation with filter(s).
3. Temperature rises in the table are approximate. Actual temperature rises may vary.
4. Temperature rises that are shaded grey are for reference only. These conditions are not recommended.
5. For single stage cooling, the indoor blower will operate at the CFM listed in the high column.

7
SAFETY INFORMATION
1. Use only with type of gas approved for this furnace.
Refer to the furnace rating plate.
2. Install this furnace only in a location and position as
specified on Table 3 of these instructions.
3. Provide adequate combustion and ventilation air to the
furnace space as specified on Pages 11 through 14.
4. Combustion products must be discharged outdoors.
Connect this furnace to an approved vent system only,
as specified on Pages 13 through 14.
5. Never test for gas leaks with an open flame. Use a
commercially available soap solution made specifi-
cally for the detection of leaks to check all connections,
as specified on Page 17 of these instructions.
6. Always install furnace to operate within the furnace’s
intended temperature-rise range with a duct system
which has an external static pressure within the allow-
able range, as specified on Table 2 of these instruc-
tions. See furnace rating plate.
7. When a furnace is installed so that supply ducts carry
air circulated by the furnace to areas outside the space
containing the furnace, the return air shall also be
handled by duct(s) sealed to the furnace casing and
terminating outside the space containing the furnace.
8. A gas-fired furnace for installation in a residential
garage must be installed as specified on Page 6 of
these instructions.
9. The furnace is not to be used for temporary heating of
buildings or structures under construction.
INSTALLATION REQUIREMENTS
Requirements and Codes
This furnace must be installed in accordance with these
instructions, all applicable local building codes, current
revision of the National Fuel Gas Code (ANSI-Z223.1), and
in Canada with the CAN/CGA - B149 installation code. The
current revision of the National Fuel Gas Code is available
from:
American National Standards Institute, Inc.
1430 Broadway
New York, New York 10018
Additional helpful publications are:
NFPA-90A - Installation of
Air Conditioning and Ventilating Systems
NFPA-90B - Warm Air Heating
and Air Conditioning Systems
These publications are available from:
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, Massachusetts 02269
!WARNING:
This furnace is not approved for installation in
mobile homes. Installation in a mobile home
could cause fire, property damage, and/or
personal injury.
Location
Upflow gas furnaces are shipped ready for installation in the
upflow or horizontal right or left positions. The furnace must
be installed on a level surface, located as close to the vent
(or chimney) and as close to the center of the air distribution
system as possible. See Table 1 for overall dimensions
todetermine therequired clearancesin hallways,doorways,
stairs, etc. to allow the furnace to be moved to the
installation point. The furnace must be installed so that all
electricalcomponents areprotected fromwater. The furnace
must be installed upstream from a refrigeration system.
This furnace is not to be used for temporary heating of
buildings or structures under construction.
Clearances to Combustibles
This furnace is Design Certified by CSA International for
the minimum clearances to combustible material listed in
Table 3. Refer to the furnace rating plate, located inside of
the furnace cabinet, for the specific model number and
clearance information.
Access for positioning and servicing the unit must be
considered when locating unit. 24 inches is the minimum
required clearance from the front of the unit for servicing
it. 30 inches is the minimum required clearance from the
front of the unit for positioning it. 36 inches is the
recommended clearance from the front of the unit.
Please note that a panel or door can be located such that
the minimum clearance on the rating plate is satisfied, but
that panel or door must be removable and allow the
appropriate clearance for your installation.
This furnace is certified for use on wood flooring. This
furnace must not be installed directly on carpeting, tile, or
any combustible material other than wood flooring.
A gas-fired furnace installed in a residential garage must be
installed so the burners and the igniter are located not less
than 18 inches (457 mm) above the floor, and the furnace
must be located or protected to avoid physical damage by
vehicles.

8
3. The following types of installation may require Outdoor
Air for combustion, due to chemical exposures:
• Commercial buildings
• Buildings with indoor pools
• Furnaces installed in laundry rooms
• Furnaces installed in hobby or craft rooms
• Furnaces installed near chemical storage areas
Exposure to the following substances in the combus-
tion air supply may also require Outdoor Air for
combustion:
• Permanent wave solutions
• Chlorinated waxes and cleaners
• Chlorine based swimming pool chemicals
• Water softening chemicals
• De-icing salts or chemicals
• Carbon tetrachloride
• Halogen type refrigerants
• Cleaning solvents (such as perchloroethylene)
• Printing inks, paint removers, varnishes, etc.
• Hydrochloric acid
• Cements and glues
• Antistatic fabric softeners for clothes dryers
• Masonry acid washing materials
!WARNING:
Furnace installation using methods other than
those described in the following sections must
comply with the National Fuel Gas Code and all
applicable local codes to provide sufficient
combustion air for the furnace.
Installation In An Unconfined Space
An unconfined space is an area including all rooms not
separated by doors with a volume greater than 50 cubic feet
per 1,000 Btuh of the combined input rates of all appliances
which draw combustion air from that space.
For example, a space including a water heater rated at
45,000 Btuh input and a furnace rated at 75,000 Btuh
requires a volume of 6,000 cubic feet [50 x (45 + 75) =
6,000] to be considered unconfined. If the space has an 8
foot ceiling, the floor area of the space must be 750 square
feet (6,000 / 8 = 750). In general, a furnace installed in an
unconfined space will not require outside air for combustion.
However, in “tight” buildings (with weather stripping and
caulk to reduce infiltration), it may be necessary to provide
outside air to ensure adequate combustion and venting,
even though the furnace is located in an unconfined space.
Installation In A Confined Space
A confined space is an area with volume less than 50 cubic
feet per 1,000 Btuh of the combined input rates of all
!WARNING:
Do not place combustible material on or against
the furnace cabinet or within 6 inches of the vent
pipe. Do not place combustible materials,
including gasoline and any other flammable
vapors and liquids, in the vicinity of the furnace.
VENTING AND COMBUSTION
AIR REQUIREMENTS
General
Provisions must be made in the installation of this furnace
toprovide anadequatesupply ofair for combustion. Detailed
instructions for determining the adequacy of an installation
can be found in the current revision of the National Fuel Gas
Code(ANSI Z223.1/ NFPA54) or in applicable local building
codes. Consult local codes for special requirements.
For Canadian installations consult Canadian Installations
Codes and (CAN/CGA B149.1 or .2).If the furnace is
operated with inadequate air for combustion
one of the flame roll-out switches located in the burner
compartment or the vent switch will open, turning off the
gas supply to the burners. These safety devices are
manually reset switches. DO NOT install jumper wires
across these switches to defeat their function. DO NOT
reset a switch without identifying and correcting the fault
condition. If a switch must be replaced, use only the
correct part specified in the Replacement Parts List.
Air openings in the furnace door, warm air registers, and
return air grilles must not be restricted.
!CAUTION:
Combustion air must not be drawn from a
corrosive atmosphere.
To maximize heat exchanger life, the combustion air must
befree ofchemicals whichform corrosiveacidic compounds
in the combustion gases.
Combustion Air Quality
The recommended source of combustion air is to use the
outdoor air supply. However, the use of indoor air in most
applications is acceptable except as follows:
1. If the furnace is installed in a confined space it is
recommended that the necessary combustion air come
from the outdoors by way of attic, crawl space, air duct,
or direct opening.
2. If outdoor combustion air is used, there must be no
exposure to the installations or substances listed in
Item 3 below.

9
appliancesdrawing combustionairfrom thatspace. Furnace
closets, small equipment rooms and garages are confined
spaces. Furnaces installed in a confined space which
supply heated air to areas outside the space must draw
return air from outside the space and must have the return
air ducts tightly sealed to the furnace. A confined space
must have two openings into the space for combustion
air. One opening must be within 12 inches of the
ceiling, and the other must be within 12 inches of the
floor. The required sizing of these openings is determined
by whether inside or outside air is used to support
combustion, the method by which the air is brought to the
space, and by the total input rate of all appliances in the
space.
Downflow Warning (*RK Models):
The design of the downflow furnace is certified for natural
or propane gas and for installation on non-combustible
flooring. A special combustible floor sub-base is required
when installing on a combustible floor. Failure to install the
sub-base may result in fire, property damage and personal
injury. The special downflow sub-bases are factory sup-
plied accessories, part numbers 902677 and 902974.
When the furnace is installed on a factory or site-built cased
air conditioning coil, the sub-base is not necessary. How-
ever, the plenum attached to the coil casing must be
installed such that its surfaces are at least 1" from
combustible construction.
!
CAUTION:
The downflow sub-base must not be installed
directly on carpeting, tile, or any combustible
material other than wood flooring.
A gas-fired furnace installed in a residential garage must be
installed so the burners and the igniter are located not less
than 18 inches (457 mm) above the floor, and the furnace
must be located or protected to avoid physical damage by
vehicles.
!WARNING:
Do not place combustible material on or against
the furnace cabinet or within 6 inches of the
vent pipe. Do not place combustible materials,
including gasoline and any other flammable
vapors and liquids, in the vicinity of the furnace.
Figure 2. Horizontal installation on a Platform
Gas Inlet
Electrical
Supply
Connection
Coil Plenum
Type “B” Vent
Combustible
Platform
Louver Door
Note: Line
Contact is Permissible
Supply Air Plenum Installation
A. Installation on a concrete slab. - *RK
1. Construct a hole in the floor per the dimensions in
Figure 2.
2. Place the plenum and the furnace as shown in Figure
3.
B. Installation on a combustible floor. - *RK
1. Cut and frame the hole in the floor per the dimensions
in Figure 4.
2. Place sub-base for combustible floors over the hole
with its duct collar extended downward. Attach the
supply air plenum to the base in a manner which will
assure 1" clearance to the flooring or other combus-
tible construction. Place furnace on the combustible
base as shown in Figure 6.
3. When a factory or site built cased coil is provided
beneath the furnace the sub-base for combustible
floors is not necessary. However, the plenum at-
tached to the cased coil must be installed such that its
surfaces are at least 1" from the flooring or other
combustible construction.
Horizontal Furnace Installation
This furnace can be installed horizontally in an attic,
basement, crawl space or alcove. It can be suspended
from a ceiling in a basement or utility room in either a right
to left airflow or left to right airflow. (See Figure 2.)
If the furnace is to be suspended from the ceiling, it will be
necessary to use steel straps around each end of the
furnace. These straps should be attached to the furnace
with sheet metal screws and to the rafters with bolts. The
furnace could also be suspended by an angle iron frame
bolted to the rafters.

10
Table 3. Minimum Clearances to Combustible Material
LEFT
SIDE
BOTTOM
TOP
RIGHT
SIDE
DOWNFLOW APPLICATION
Downflow Furnace Models
* For Downflow furnace installations only,
right side minimum clearance is 0".
** For Downflow furnace installations only,
furnace must be installed on non-
combustible flooring.
*** Allow 24" minimum clearance for servicing.
The recommended clearance is 36".
Vent Connector
Type
Standard Single
Wall Metal Vent
Type B-1 Double
Wall Metal Vent
LEFT SIDE
0" 0"
RIGHT SIDE
5"* 0"
VENT
6" 1"
BACK
0" 0"
BOTTOM
0"** 0"**
TOP
1" 1"
FRONT
4"*** 4"***
UPFLOW/DOWNFLOW INSTALLATION CLEARANCES
LEFT
SIDE
RIGHT
SIDE
Upflow Furnace Models
BOTTOM
UPFLOW APPLICATION
TOP
*** Allow 24" minimum clearance for servicing. The
recommended clearance is 36".
TOP
RIGHT
SIDE
HORIZONTAL APPLICATION
BOTTOM
Vent Connector
Type
Standard Single
Wall Metal Vent
Type B-1 Double
Wall Metal Vent
LEFT SIDE
1" 1"
RIGHT SIDE
0" 0"
VENT
6" 1"
BACK
0" 0"
BOTTOM
0" 0"
TOP
5" 0"
FRONT
4"*** 4"***
HORIZONTAL INSTALLATION CLEARANCES
LEFT
SIDE

11
1 inch thick fiberglass 3 lb density
28.38"
9.25"
19.63"
3"
19.75"
or 14.25"*
2.0"
1.58"
1.50"
16.75"
or 11.25"*
18.75"
or 13.25"*
Figure 5. Downflow Sub-Base Dimensions
* Smaller dimensions for *RK
060-12; 072-12
Downflow Wood
Sub-base Floor
Furnace
Sheet
Metal
Plenum
Figure 6. Downflow Sub-Base Dimensions
Hole in
Floor
19.25"
18.75"
Hole in
Floor
19.25"
13.25"
*RK 072-16; 096-12; 096-16;
120-20
*RK 060-12;
072-12
Figure 3a. Opening for Concrete Slab
Concrete
Floor
Furnace
Sheet
Metal
Plenum
Figure 3b. Furnace on a Concrete Slab
19.63"
18.75"
19.63"
13.25"
Hole in
Floor
Hole in
Floor
*RK 072-16;
096-12; 096-16; 120-20 *RK 060-12;
072-12
Figure 4. Opening in Wood Floor
Access for positioning and servicing must be considered
when locating the unit. Refer to Table 3, Minimum
Clearances to Combustible Material, for clearance
specifications.
Keep all insulating materials away from the louvered door.
Insulating materials may be combustible.
This furnace may be installed directly on combustible wood
flooring or supports, if type "B-1" vent pipe is used (See
Figure 4). It is recommended for further reduction of fire
hazard that cement board or sheet metal be placed between
the furnace and the combustible floor and extend 12 inches
beyond the front of the louvered door.
!WARNING:
Furnaces installed with combustion air drawn
from a heated space which includes exhaust
fans, fireplaces, or other devices that may
produce a negative pressure should be
considered confined space installations.
See the venting section for venting guidelines and
specifications.
Air From Inside (See Figure 7)
If combustion air is taken from the heated space, the two
openings must each have a free area of at least one square
inch per 1,000 Btuh of total input of all appliances in the
confined space, but not less than 100 square inches of
free area. For example, if the combined input rate of all
appliances is less than or equal to 100,000 Btuh, each
opening must have a free area of at least 100 square
inches. If the combined input rate of all appliances is
120,000 Btuh, each opening must have a free area of at
least 120 square inches.

12
Total Input
Rating (Btu/hr)
40,000
60,000
80,000
100,000
120,000
140,000
160,000
Round Duct
Diameter
12"
12"
12"
12"
13"
14"
15"
Minimum
Free Area
(Each Opening)
100 sq. in.
100 sq. in.
100 sq. in.
100 sq. in.
120 sq. in.
140 sq. in.
160 sq. in.
Furnace
Openings to
adjacent space.
Each opening must
be at least 100 sq. in.
or 1 sq. in. per 1000
Btuh of total input
rating, whichever is
greater. See minimum
area per table.
12" Max.
12" Max.
Water Heater
Vent or
Chimney
Figure 7. Equipment in a Confined Space with all
Combustion Air Drawn from the Inside
Total Input
Rating (Btu/hr)
40,000
60,000
80,000
100,000
120,000
140,000
160,000
Minimum
Free Area
(Each Opening)
10 sq. in.
15 sq. in.
20 sq. in.
25 sq. in.
30 sq. in.
35 sq. in.
40 sq. in.
Round Duct
Diameter
4"
5"
5"
6"
6"
7"
8"
Inlet Air Duct must
be at least 1 sq. in.
per 4,000 Btuh of
total input rating.
Inlet and Outlet
Ducts must
extend above
attic insulation.
Outlet Air Duct must
be at least 1 sq. in.
per 4,000 Btuh of
total input rating.
Ventilation Louvers at
each end of attic
Attic
Insulation
12" Max
a. All Combustion Air from Ventilated Attic.
Furnace
Water Heater
Vent or
Chimney
Figure 8. Equipment in a Confined Space with all
Combustion Air Drawn from the Outside
through Vertical Ducts
Figure 9. Equipment in a Confined Space with all
Combustion Air Drawn from the Outside
through Exterior Wall
Each opening
to outside
must be at least
1 sq. in. per 4000
Btuh of total input
rating.
12" Max
12" Max
Total Input
Rating (Btuh)
40,000
60,000
80,000
100,000
120,000
140,000
160,000
Minimum
Free Area
(Each Opening)
10 sq. in.
15 sq. in.
20 sq. in.
25 sq. in.
30 sq. in.
35 sq. in.
40 sq. in.
Round Duct
Diameter
4"
5"
5"
6"
6"
7"
8"
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Furnace
Water Heater
Vent or
Chimney
The combustion air openings must not be restricted in any
manner.
!CAUTION:
Do not supply combustion air from an attic space
that is equipped with power ventilation or any
other device that may produce a negative
pressure.
Air Directly Through An Exterior Wall
(See Figure 9)
If combustion air is provided directly through an exterior
wall, the two openings must each have free area of at least
one square inch per 4000 Btuh of total appliance input.
Outdoor Air Using a Crawl Space and Ventilated
Attic (See Figure 10)
When directly communicating with the outdoors, each
opening shall have a minimum free area of 1 square inch per
4,000 Btuh of total appliance input. The openings shall
communicate directly, or by ducts, with the outdoor spaces
(crawl or attic) that freely communicate with the outdoors.
Outdoor Air Using Horizontal Ducts (See Figure 11)
If combustion air is taken from outdoors through horizontal
ducts, the openings and ducts must have a minimum free
area of one square inch per 2,000 Btuh of total appliance
input.
Outdoor Air Using Vertical Ducts
(See Figure 8)
If combustion air is taken from outdoors through vertical
ducts, the openings and ducts must have a minimum free
area of one square inch per 4,000 Btuh of total appliance
input.In installationsdrawing combustion airfrom aventilated
attic, both air ducts must extend above the attic insulation.
If the unit is installed in an area with an exhaust fan, provide
sufficient ventilation to prevent negative pressures from
occurring in the room.

13
Figure 11. Equipment in a Confined Space with all
Combustion Air Drawn from the Outside through
Horizontal Ducts
Each opening
to outside
must be at least
1 sq. in. per 2000
Btuh of total input
rating.
12" Max
12" Max
Total Input
Rating (Btu/hr)
40,000
60,000
80,000
100,000
120,000
140,000
160,000
Minimum
Free Area
(Each Opening)
20 sq. in.
30 sq. in.
40 sq. in.
50 sq. in.
60 sq. in.
70 sq. in.
80 sq. in.
Round Duct
Diameter
5"
6"
7"
8"
9"
10"
10"
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Furnace
Air Duct
Air Duct
Water Heater
Vent or
Chimney
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Figure 10. Equipment in a Confined Space with All
Combustion Air Drawn from a
Crawl Space and Ventilated Attic
Outlet Air Duct
must be at least
1 sq. in. per 4000
Btuh of total input
rating. Must extend
above attic insulation.
Ventilation Louvers at
each end of attic
Attic Insulation
Ventilation Louvers for
unheated crawl space Crawl Space
Inlet Air Duct must
be at least 1 sq. in.
per 4,000 Btuh of
total input rating.
Furnace
Water Heater
Vent or
Chimney
If the unit is installed in an area with an exhaust fan, provide
sufficient ventilation to prevent negative pressures from
occurring in the room.
The combustion air openings must not be restricted in any
manner.
VENTING REQUIREMENTS
General
This furnace must be vented in compliance with, the current
revision of the National Fuel Gas Code (ANSI-Z223.1/
NFPA54), with the instructions provided below.
In Canada, venting shall conform to the requirements of the
current(CAN/CGA B149.1or .2) installation codes. Consult
local codes for special requirements.
This furnace must never be vented to a chimney flue
servicing a fireplace or other appliance designed to burn
solid fuel. If the furnace vent is to be connected to a
chimney serving a fireplace, the fireplace must be sealed
off from the chimney.
For Category I furnace installations, the furnace shall be
connected to a factory built chimney or vent complying with
a recognized standard, or a masonry or concrete chimney
lined with a lining material acceptable to the authority
having jurisdiction. Venting into an unlined masonry
chimney or concrete chimney is prohibited.
The furnace vent, if metal, may be insulated if local codes
allow. Any part of the vent system, metal vent only, not
exposed to weather, but which are exposed to ambient
temperatures below 35° F must be insulated to prevent
condensation. All vent insulation shall be foil backed
fiberglass of one inch minimum thickness.
Three sheet metal fasteners (field supplied) should be used
to secure the vent pipe to the furnace flue. These fasteners
should be evenly spaced around the flue diameter, if
possible.
Category I - Common Venting
When an existing furnace is removed from a venting system
serving other appliances, the venting system is likely to be too
largetoproperlyventthe remaining appliances.Animproperly
sizedventingsystemcanresultinthe formation ofcondensate,
leakage, spillage, etc.
The venting system should be designed to have the
minimum number of elbows or turns. All horizontal runs
shall be sloped upwards from the furnace at 1/4 inch per
running foot of vent. Supports for the vent pipe must be
installed a minimum of every five feet along the vent run to
ensure no displacement after installation.
Under no circumstances shall any portion of the vent
system extend into or pass through any return air duct,
supply air duct, or plenum.
If the furnace is operated with blocked or restricted venting,
the blocked vent switch located in the vent plate will open,
turning off the gas supply to the burners. The blocked vent
switch is a manually reset device. DO NOT install a jumper

14
!WARNING:
CARBON MONOXIDE POISONING HAZARD
Failure to follow the steps outlined below for each appliance connected to the venting system
being placed into operation could result in carbon monoxide poisoning or death.
The following steps shall be followed for each appliance connected to the venting system being
placed into operation, while all other appliances connected to the venting system are not in
operation:
1. Seal any unused openings in the venting system.
2. Inspect the venting system for proper size and horizontal pitch, as required in the
National Fuel Gas Code, ANSI Z223. 1/NFPA 54 or the CSA B149.1, Natural Gas and
Propane Installation Codes
and these instructions. Determine that there is no blockage
or restriction, leakage, corrosion and other deficiencies which could cause an unsafe
condition.
3. As far as practical, close all building doors and windows and all doors between the
space in which the appliance(s) connected to the venting system are located and other
spaces of the building.
4. Close fireplace dampers.
5. Turn on clothes dryers and any appliance not connected to the venting system. Turn
on any exhaust fans, such as range hoods and bathroom exhausts, so they are
operating at maximum speed. Do not operate a summer exhaust fan.
6. Follow the lighting instructions. Place the appliance being inspected into operation.
Adjust the thermostat so appliance is operating continuously.
7. Test for spillage from draft hood equipped appliances at the draft hood relief opening
after 5 minutes of main burner operation. Use the flame of a match or candle.
8. If improper venting is observed during any of the above tests, the venting system must
be corrected in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 and/
or CSA B149.1, Natural Gas and Propane Installation Codes .
9. After it has been determined that each appliance connected to the venting system
properly vents when tested as outlined above, return doors, windows, exhaust fans,
fireplace dampers and any other gas-fired burning appliance to their previous conditions
of use.
wire across this switch to defeat its function. DO NOT reset
the switch without identifying and correcting the fault
condition which caused the switch to trip. If this switch
must be replaced, use only the part specified in the
Replacement Parts List.
!WARNING:
Upon completion of the furnace installation,
carefully inspect the entire flue system both
inside and outside the furnace to assure it is
properly sealed. Leaks in the flue system can
result in serious personal injury or death due to
exposure of flue products, including carbon
monoxide.
Category III: Horizontal Venting
NOTE: The reduced NOx models (eighth character N)
are not approved as a Category III furnace for use with
horizontal venting.
The furnaces are approved for use with 3" single wall AL29-
4C stainless steel vent pipe in horizontal vent applications.
This pipe is available from the following manufacturers:
Z-FLEX Inc. - vent brand name (Z-VENT)
Heat-fab Inc. - vent brand name (Saf-T Vent)
Flex-L International - vent brand name (Star-34 Vent)
This vent pipe must be used for the entire length of the vent
run. The installation must be in accordance with all
instructions supplied by the vent manufacturer for use on
Category III appliances. When venting horizontal, this is

15
Figure 12. Bleed Tube Installation
Collector
Pan
Pressure
Switch
Cut
Sensor
Tubes Bleed Tube
Bleed Tube
Orifice
Figure 14. Limit Circuit Wiring
Wire Nut
Switch
Limit
Switch
Flame
Roll-Out
Switch
Vent
Limit
Blue
Blue
Figure 13. Vent Collar Detail
Cover
Plate
Nut
Covered Vent
Collar Hole
Figure 15. Typical Horizontal Vent Installation
90 ˚ Elbow
3" Dia. Loop Outside
Wall
Wall Thimble
(For combustible
wall material)
Termination
Tee
Support
Tee
0-6'
Drain
Plug
1
/ 4 " Per
Foot Rise
Locking Band Locking
Band
defined as a Category III furnace, the vent pressure is
positive, and the venting system must be sealed in both
horizontal and vertical runs.
For horizontal venting installations in both the United
Statesand Canadathe transitionassembly must bemodified
by adding a bleed tube to the pressure switch tube and
bypassing the vent switch. All model furnaces will require
Vent Kit #903196 for horizontal venting.
Horizontal Venting For Upflow Models:
1. Remove the rubber tubing from the pressure switch
sensor tube and the collector pan sensor tube. Cut
1/2 inch from one end of the rubber sensor tube, fold
in half and cut along the bend line. Discard the 1/2
inch long piece of tubing. Select the correct bleed
tube using the table supplied with vent kit #903196
and place the other two pieces of tubing on both ends
of the bleed tube. Do not cover the hole in the bleed
tube. Place the assembly back on the pressure
switch sensor tube and the collector pan sensor
tube. (See Figure 12.)
2. Remove the nut and restrictor plate from the vent
collar assembly and discard the restrictor plate.
Select the appropriate dilution cover plate as noted
with vent kit #903196. Fit the clearance hole in the
cover plate over the weld stud. The cover plate must
cover the hole(s) on the vent collar assembly.
Tighten the nut securely while holding the cover plate
in position. (See Figure 13.)
3. Bypass the vent switch by removing both wires from
the vent switch and attaching them to the wire nut.
(See Figure 14.)
!CAUTION:
Do not drill holes through the vent pipe or fittings
on a horizontal vented furnace. Do not use sheet
metal screws, or rivets. Drilling, screws, or
rivets will cause leaks.
The components of the horizontal vent system must not be
penetrated with screws, rivets, or other devices, either
when joining pipes and fittings or using support straps. All
joints must be sealed with high temperature silicone before
locking bands are installed. If the lengths of pipe must be
cut, the joint must still be sealed with silicone and the
locking band used. When installing the condensate tube be
sure to form a trap by means of a 3" loop filled with water.
(See Figure 15.)
Horizontal Venting: *RK Models:
1. By-pass the vent switch, located on blower compart-
ment door, by removing both wires from the switch.
Remove wire terminals, strip wires and tie together in a
wire nut. (See Figure 16.)

16
Bleed Tube
Bleed Tube
Orifice
Collector
Pan
Pressure
Switch
Figure 18. *RK Reducer Installation
Transition
4" to 3" Reducer
Special 3"
AL29-4C Stainless Steel
Vent Pipe
Figure 17. *RK Horizontal
Vent Modification
Figure 16. *RK Bleed Tube Installation
2. Remove the rubber tubing from the pressure switch
sensor tube and the collector pan sensor tube. Cut the
tubing approximately 3" from one end. Select the
appropriate dilution cover plate as noted with vent kit
#903196. Insert the bleed tube into the tubing. Do not
cover the hole in the bleed tube. Place the tubing
assembly back on the pressure switch sensor tube and
collector pan sensor tube. (See Figure 16.)
3. To gain access to the restrictor plate, remove and
discard the combustion tube from the transition assem-
bly. Insure the seal between inducer and transition
assembly is not broken. (See Figure 17.)
4. Remove and discard the restrictor plate and screw from
the transition assembly. (See Figure 17.)
5. Install and seal a 4" to 3" reducer to the transition. (See
Figure 18.) Attach the new high temperature vent pipe
to the reducer.
The components of the horizontal vent system must not be
penetrated with screws, rivets, or other devices, either
when joining pipes and fittings or using support straps. All
joints must be sealed with high temperature silicone before
locking bands are installed. If the lengths of pipe must be
cut, the joint must still be sealed with silicone and the
locking band used. When installing the condensate tube be
sure to form a trap by means of a 3" loop filled with water.
(See Figure 15.)
Keep the number of pipe fittings to a minimum. Maintain a
minimum of 6 inches of air space between the vent and
combustibles at all times, this includes inside and outside
the building.
NOTE: The direction of the male-female joints from the
drain tee to the termination tee is opposite to standard gas
appliance venting. The male end of the pipes point towards
the furnace.
1. Apply an adhesive bead around the outside of the
pipe approximately 1/4" from the end of the pipe.
This includes the first fitting or pipe attached to the
furnace.
2. Push the pipe and fitting together while twisting the
pipe or fitting. Twisting the pipe or fitting spreads the
adhesive completely within the fitting socket.
3. When the pipe is at the socket bottom, inspect the
joint. Look for a complete, uninterrupted ring of
adhesive material around the pipe at the fitting
socket. Additional adhesive or rotation of the pipe or
fitting may be required for a complete seal. The
Transition
Inducer
Remove
and
Discard
Combustion
Tube
Screw
Restrictor
Plate

17
Table 4. Horizontal Venting Requirements
Horizontal Venting Requirements
Furnace
Model Number Pipe Reducer Maximum Max. Feet
*RA Size Needed # Elbows Vent Pipe
072C-12 3" 4" to 3" 4 35
096C-12 3" 4" to 3" 4 35
096C-16 3" 4" to 3" 4 35
096C-20 3" 4" to 3" 4 35
120C-16 3" 4" to 3" 4 35
120C-20 3" 4" to 3" 4 35
144C-20 3" 4" to 3" 3 30
Note: Special 5" to 4" Reducer Kit, p/n 902249 required for model
number *RA144C-20.
Furnace
Model Number Pipe Reducer Maximum Max. Feet
*RK Size Needed # Elbows Vent Pipe
060C-12 3" 4" to 3" 4 35
072C-12 3" 4" to 3" 4 35
072C-16 3" 4" to 3" 4 35
096C-12 3" 4" to 3" 4 35
096C-16 3" 4" to 3" 4 35
120C-20 3" 4" to 3" 4 35
complete adhesive material ring provides the seal
required for the positive pressure vent.
4. All vent systems must include a tee and drain plug
for collection and disposal of condensate. The drain
tee must be installed within the first 5 feet of vent run
to protect the furnace.
5. All horizontal sections must have a slope toward the
drain tee of not less than 1/4" per foot to prevent the
collection of condensate at any location other than at
the tee.
6. Horizontal runs must be supported with 3/4" pipe
strap at a maximum of 5 foot intervals and at each
point where an elbow is used.
7. Maintain a 6 inch minimum air space to combustibles
from all sections of the stainless steel vent system,
except when a wall thimble is used.
Horizontal Power Venting — The Tjerlund GPAK-1TN
horizontal kit is certified for use with *RA, *RK Series
furnaces. The kit includes a power venter, a side-wall vent
hood and a barometric draft control. It has an electrical
interlock to assure that the furnace will not operate when
the power venter is off.
The kit is for use only when exhaust is through an exterior
wall, normally with horizontal vent piping. The power venter
establishes negative pressure in the vent piping and the
furnace operates as if connected to Category I vertical
venting.
Installation Instructions are provided with the kit. Installation
must conform to those instructions and applicable
requirements of local codes.
!WARNING:
The entire vent system must be sealed with a
high temperature sealant which will withstand
temperatures of 450°F. Recommended sealants:
Dow Corning Sealant 736 RTV; GE 106 RTV;
High Tech Ind., High TEMP RED.
Location of Outdoor Terminations
Horizontal Installation
The vent termination tee must be installed with the following
minimum clearances. (See Figure 19.) Vent Termination
clearances shall be consistant with the National Fuel Gas
Code, ANSI 2223.1/NFPA 54 and/or the CSA B149.1,
Natural Gas and Propane Installation Code.
All minimum clearances specified must be maintained to
protect building material from degradation by flue gases.
1. The termination tee must be 12 inches above
snow level or grade level which ever is higher. See
Figure 14 for alternate method to achieve 12"
above snow level.
2. The minimum distance from any door, (openable)
window, or gravity air inlet is 4 ft. below, 4 ft.
horizontally, or 1 ft. above.
3. The vent termination shall be a minimum of 3 ft. above
any forced air inlet within 10 ft. (See Figure 19.)
4. Recommended minimum distance from an inside
corner formed by two exterior walls is 6 ft., but is not
required.
5. The minimum distance from gas or electric meter(s)
is 4 ft.
6. Avoid areas where condensate drainage may cause
problems such as above planters, patios, or adjacent
to windows where the steam from the flue gases
may cause fogging. Do not terminate above any
public walkway.
7. Selectthe pointofwall penetrationwherethe minimum
1/4 inch per foot of upward slope can be maintained.
8. When penetrating a noncombustible wall, the hole
through the wall must be large enough to maintain the
pitch, pipe clearance for passage, and provide for
proper sealing. Penetrating a combustible wall
requires the use of a wall thimble. (See Figure 20.) A
6-1/2 inch square framed opening is required to insert
the thimble halves. The thimble is adjustable to
varying wall thickness and is held in place by
applying sealant to the male sleeve before assembly.
Also run a bead of sealant around the outer wall
thimble.

18
Figure 19. Vent Termination Clearances
VENT TERMINAL AIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED
1In accordance with the current CSA B149.1 Natural Gas and Propand Installation Code
2In accordance with the current ANSI Z223.1 / NFPA 54 National Fuel Gas Code
† A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings.
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
* For clearances not specified in ANSI Z223.1 / NFPA 54 or CSA B149.1, one of the following statements shall be included:
“Clearance in accordance with local installation codes, and the requirements of the gas supplier
and the manufacturer’s installation instructions.”
Canadian Installations
1
US Installations
2
A = Clearance above grade, veranda, porch,
deck, or balcony
12 inches (30 cm) 12 inches (30 cm)
B = Clearance to window or door that may be
opened
6 inches (15 cm) for appliances ≤10,000
Btuh (3 kW), 12 inches (30 cm) for
appliances > 10,000 Btuh (3 kW) and ≤
100,00 Btuh (30 kW), 36 inches (91 cm) for
appliances >100,00 Btuh (30 kW)
4 feet (1.2 m) below or to side of opening;
1 foot (300 mm) above opening
C = Clearance to permanently closed window **
D = Vertical clearance to ventilated soffit
located above the terminal within a
horizontal distance of 2 feet (61 cm) f rom
the center line of the terminal
**
E = Clearance to unventilated soffit **
F = Clearance to outside corner **
G = Clearance to inside corner **
H = Clearance to each side of center line
extended above meter/regulator assembly
3 feet (91 cm) within a height 15 feet
above the meter/regulator assembly *
I = Clearance to service regulator vent outlet 3 feet (1.83 m) *
J = Clearance to nonmechanical air supply inlet
to building or the combustion air inlet to any
other appliance
6 inches (15 cm) for appliances ≤10,000
Btuh (3 kW), 12 inches (30 cm) for
appliances > 10,000 Btuh (3 kW) and ≤
100,00 Btuh (30 kW), 36 inches (91 cm) for
appliances >100,00 Btuh (30 kW)
4 feet (1.2 m) below or to side of opening;
1 foot (300 mm) above opening
K = Clearance to a mechanical air supply inlet 6 feet (1.83 m) 3 feet (91 cm) above if within 10 feet (3 m)
horizontally
L = Clearance above paved sidewalk or paved
driveway located on public property
7 feet (2.13 m) † 7 feet (2.13 m)
M = Clearance under veranda, porch deck, or
balcony
12 inches (30 cm) ‡ *

19
Figure 20. Alternate Horizontal Vent Installation
Use Wall Thimble at
Vent Points
Support
Ground Level
Termination Tee
exchanger. The cover for the opening shall be attached in
such a manner as to prevent leaks.
If outside air is used as return air to the furnace for
ventilation or to improve indoor air quality, the system must
be designed so that the return air is not less than 50° F
(10° C) during operation. If a combination of indoor and
outdoor air is used, the ducts and damper system must be
designed so that the return air supply to the furnace is equal
to the return air supply under normal, indoor return air
applications.
When a cooling system is installed which uses the furnace
blower to provide airflow over the indoor coil, the coil must
be installed downstream (on the outlet side) of the furnace
or in parallel with the furnace.
If a cooling system is installed in parallel with the furnace,
a damper must be installed to prevent chilled air from
enteringthe furnaceand condensingon theheat exchanger.
If a manually operated damper is installed, it must be
designed so that operation of the furnace is prevented when
the damper is in the cooling position and operation of the
cooling system is prevented when the damper is in the
heating position.
Return Air
In applications where the supply ducts carry heated air to
areas outside the space in which the furnace is installed,
the return air must be delivered to the furnace by duct(s)
sealed to the furnace casing, running full size and without
interruption.
!WARNING:
The solid base of the furnace must be in place
when the furnace is installed with side return
air ducts. Removal of all or part of the base
could cause products of combustion to be
circulated into the living space and create
potentially hazardous conditions, including
carbon monoxide poisoning that could result
in personal injury or death.
Wall Thimble
(Inner Half)
Inner Shield
4
1
/ 2 " Dia.
Wall Thimble Outer Half
Outer Overlapping
Shield 6
1
/ 2 " Dia.
3" Termination
Tee
Protective
Screen
Inside
Combustible
Wall
Inside
Combustible
Wall
3" Vent
Pipe
Outside
Combustible
Wall
Inner
Overlapping
Shield 6
3
/ 8 " Dia.
Locking Band
12" Min
Figure 21. Typical Termination
9. The vent pipe must extend 1-1/4 inches through the
outer thimble half for a combustible wall. Be sure to
check this carefully before cutting the vent pipe.
10. Attach a 3 inch coupling to the end of the pipe that
extends through the wall or thimble. This prevents
the vent pipe from being pushed inward.
11. Cut an 8 inch minimum piece of vent pipe and
connect the coupling to the termination tee. The
inside of the tee must be a minimum of 12 inches
from the outside of the wall. (See Figure 21.)
Flexible Vent Systems
Flexible gas vent is approved for use in vertical single vent
or common vent installations only. The minimum distance
to combustibles is 1" for type B insulated and 6" for single
wall. The venting system must be installed in accordance
withthe localauthorities,the ventmanufacturer's instructions
and the instructions listed below.
The flexible vent must be installed in accordance with the
venting tables for vertical or common venting only. The
vent system must be supported in horizontal runs with
3/4" pipe strap at a maximum of 5 foot intervals. All
horizontal sections must have a slope toward the furnace
of not less than 1/4" per foot. The vent must not sag, or
have any bends greater than 90 degrees.
CIRCULATING AIR SUPPLY
General
Plenums and air ducts must be installed in accordance with
the Standard for the Installation of Air Conditioning and
Ventilating Systems (NFPA No. 90A) or the Standard for
the Installation of Warm Air Heating and Air Conditioning
Systems (NFPA No. 90B).
It is recommended that the outlet duct be provided with a
removableaccess panel.This openingshould beaccessible
when the furnace is installed in service and shall be of a
size that smoke or reflected light may be observed inside
the casing to indicate the presence of leaks in the heat

20
!WARNING:
Products of combustion must not be allowed
to enter the return air ductwork or the circulating
air supply. Failure to prevent products of
combustion from being circulated into the living
space can create potentially hazardous
conditions including carbon monoxide
poisoning that could result in personal injury
or death.
All return ductwork must be secured to the
furnace with sheet metal screws. For
installations in confined spaces, all return
ductwork must be adequately sealed and joints
must be taped. When return air is provided
through the bottom of the furnace, the joint
between the furnace and the return air plenum
must be air tight.
The floor or platform on which the furnace is
mounted must provide sound physical support
of the furnace with no gaps, cracks, or sagging
between the furnace and the floor or platform.
Return air and circulating air ductwork must
not be connected to any other heat producing
device such as a fireplace insert, stove, etc.
Doing so may result in fire, explosion, carbon
monoxide poisoning, personal injury, or
property damage.
For *RA installations: The return air ductwork may be
connected to any or all of the following: left side return, right
side return, or bottom return. NOTE: Do not use the back
of the furnace for return air. Table 2 in the front of these
instructions, contains the airflow data for this furnace
model. Where maximum airflow is 1800 CFM or more, two
openings must be used for return air.
GAS SUPPLY AND PIPING
General
This furnace may be installed for either left or right side gas
entry. A typical gas service hookup is shown in Figure 22.
Whenmakingthe gasconnection provideclearancebetween
the gas supply line and the entry hole in the furnace casing
to avoid unwanted noise and/or damage to the furnace. All
gas piping must be installed in compliance with local
codes and utility regulations. Some local regulations
require the installation of a manual main shut-off valve and
ground joint union external to the furnace. The shut-off
valve should be readily accessible for service and/or
emergency use. Consult the local utility or gas supplier for
additional requirements regarding placement of the manual
main gas shut-off. In the absence of local codes the gas
line installation must comply with the latest edition of the
National Fuel Gas Code (ANSI Z223.1) or (CAN/CGA
B149.1 or .2) Installation Codes.
If desirable an 1/8 inch NPT tap must be installed in the
gas line to the unit for use when measuring the gas supply
pressure. The tap should be readily accessible for service
use. A drip leg should be installed in the vertical pipe run
to the unit. Table 5 lists gas flow capacities for standard
pipe sizes as a function of length in typical applications
based on nominal pressure drop in the line.
IMPORTANT NOTES:
1. Gas piping must not be run in or through air ducts,
chimneys, gas vents, elevator shafts, etc.
2. Compounds used on threaded joints of gas piping
must be resistant to the actions of liquefied
petroleum gases.
3. Themain manual gas valveandmain power disconnect
tothe furnacemust beproperly labeledby theinstaller
in case emergency shutdown is required.
Upflow Models- Left Side Entry
Figure 22. Typical Gas Service Connection Upflow
Downflow Models- Right Side Entry
Figure 23. Typical Gas Service Connection
Ground Joint
Union
Dripleg
Shut-Off Valve
Manifold
Some utilities
require Shut-Off
Valve to be
4 to 5 feet
above floor
Automatic Gas
Valve (with manual
shut-off)
Burner
Assembly
Ground Joint
Union
Dripleg
Shut-Off Valve
Burner
Assembly
Manifold
Some utilities
require Shut-Off
Valve to be
4 to 5 feet
above floor
Automatic Gas
Valve (with manual
shut-off)