Omnitron Systems Technology Universal DIN Rail Mounting Bracket 8250-0 User manual

Figure 2. Mounting Orientations
UniDIN™
DIN Rail Mounting Bracket Kit for
FlexPoint™and iConverter®User Manual
OVERVIEW
TheOmnitronUniversalDINRailMountingBracketmodel8250-0isdesigned
toprovideDINRailmountingcapabilitiesfortheFlexPointconverter,FlexPoint
converterwithDCAdapter,iConverter®Stand-Alone andiConverter 1-module
chassis. This kit contains all the necessary components to provide DIN Rail
mountingforseveraldifferent mounting orientations.
[D]
[B]
[A]
[C]
Figure 1. Pre-assembled Configuration - Mounting Orientation [B]
MOUNTING ORIENTATIONS
ThisdiagramillustratesaconverterinfourdifferentDIN-Railmountingorientations.
As shipped from the factory, the UniDIN is ready to be used in configuration [B].
Model: 8250-0
j
Rear Cover Screw
Converter
Front Cover
Screw
i
i
PACKAGE CONTENTS
(2)DINRailBracketHex
Nuts(Pre-assembled) (2)DINRailClips
(Pre-assembled)
(2)DINRailClipScrews
(Pre-assembled) (4)BracketMounting Screws(Inseparatebag)
(2)DINRailBracket
Halves(Pre-assembled)
UserManual
Item i Item j Item k
Item m Item n
ASSEMBLY AND MOUNTING INSTRUCTIONS
STEP 1. Adjusting Bracket Width
If bracket width adjustment is necessary, loosen the hex nuts ( j) on the DIN
Rail bracket ( i) and align the DIN Rail bracket width to match the width of the
mediaconverter. After adjustingtheDINRailbrackettothedesiredwidth,
tighten the hex nuts ( j) to lock the DIN Rail bracket width.
Figure 3. Adjusting Bracket Width to Match Width of Media Converter

k
mm
m
i
[A] and [D]
[B]
[C]
n
n
Converter
Front Cover
Screw
i
[B], [C] and [D]
[A]
i
i
k
k
STEP 2. Optional Orientation Reconfiguration
If the desired mounting orientation is other than [B] as illustrated in Fig. 2,
remove the DIN Rail clips ( k)from the bracket by removing the DIN Railclip
screws(m). Determinethe desired DINRailmountingorientationfrom the
Figure2,andmatchthe correspondingDINRail cliporientationin Figure4.
Attach the DIN Rail clips ( k) to the DIN Rail bracket holes in the DIN Rail
Bracket ( i) and secure the DIN Rail clips ( k) with DIN Rail clip screws ( m).
Figure 4. Configuring Clip Mounting Orientation
STEP 3. Attaching Bracket to Converter
Remove the rear cover screws from the media converter casing. Align the
media converter to the bracket mounting holes that correspond with desired
orientation, then insert and fasten the supplied bracket mounting screws ( n )
to secure the media converter to the DIN Rail bracket ( i ).
Figure 5. Attaching Bracket to Converter Form: 040-08250-001B 9/07 Patent Pending
DINRail
Cross Section
Close Up
Tab on the
DINRailClip
Hooks on the
DINRailClip
TECHNICAL SUPPORT:
For help with this product, contact our Technical Support:
Omnitron Systems Technology, Inc.
Phone: [phone] Fax: [phone]
Address: 140 Technology Dr., #500 Irvine, CA 92618 USA
Email: [email protected]
URL: www.omnitron-systems.com
STEP 4. Mounting Converter to the DIN Rail
Attach the assembly to the DIN Rail, by aligning the hooks on the DIN Rail clip
(k )tothe upper edge of the DINRail. Rotatetheassemblydownward until the
DIN Rail clip tab engages and snaps to the bottom edge of the DIN Rail. Note
that the tab on the DIN Rail clip should always attach to the bottom of the DIN
Rail. Connect the external power supply to the rear of the installed media
converter.
Figure 6. Mounting/Dismounting Converter to/from DIN Rail
Dismounting from DIN Rail
To remove the converter assembly from the DIN Rail, hold the converter and
rotateupwardtodisengagethe clip.
Mount
Dismount