One61 Studio foundmi 2.0 User manual

FOUNDMI TRACKER USER GUIDE
Model 2.0
www.foundmi.com

One61 foundmi Hardware
Here’s a guide to the hardware features of the One61 Studio foundmi tracker.
One61 Smartwatch tech specs:
Dimensions 50 x 44 x 10.5 mm
Weight 12.6g
Battery CR2032
Processor Nordic NRF51
Wireless Bluetooth Low Energy BLE
Memory 32kb RAM
Embedded Flash 256kb program memory
1 2 3
4
8
10
5 6 7 9
1. Keyring
2. 3M adhesive disc
3. CR2032 battery
4. Silicone face
5. Button
6. ABS front half
7. Sonically welded sides
8. ABS back half
9. Speaker
10. Back door
By numbers

Foundmi tracker battery removal and replacement
Follow the below steps 1 – 6
- Use only CR2032 batteries for the foundmi tracker.
- When replacing the battery always place the positive (+) side up. Refer to step 4 of the removal and replacement steps.
- When replacing the battery follow steps 1-6 in the reverse order.
- Your foundmi tracker is out of battery if pressing the button doesn’t cause your foundmi to ring.
Locate the back door
Locate the CR2032 battery.
Notice the positive sign is
on the top of the battery.
Apply pressure to slide the
door up to unlock the back
two tabs.
Lift the front edge of the
CR2032.
Once its loose, lift the door
straight out of the back.
Pull the CR2032 up out of the
battery contact.
1
4
2
5
3
6

Setup and Pairing
Pair your foundmi tracker with your Device
Your foundmi tracker works together with your mobile device, so you’ll need to pair them. The foundmi tracker uses Blue-
tooth Low Energy (BLE).
If you’re pairing your foundmi tracker for the first time, make sure your device Bluetooth is turned on and yourdevice is con-
nected to mobile data or Wi-Fi. You need a data connection to complete setup.
How to pair:
- Download and install the foundmi app on your device, which can be found on the Google Play or Apple AppStore by
searching “foundmi.”
- Open the foundmi app on your device and follow the onscreen prompts..
- On your device, you will need to create an account in the foundmi app.
1. Launch the app
2. Tap ‘Signup’, ‘Facebook’, or ‘Google +’
3. Enter your valid email address
4. Enter your name or desired username
5. Enter a password
6. Tap ‘Submit’

- Once you have completed your signup, you can now pair your foundmi.
1. Tap the + icon in the center of the card to ‘add foundmi’
2. Select the universe of your character by tapping on one of the licensed boxes.
3. Select your character.

4. Place your foundmi tracker close to your mobile device.
5. Long press the button on your foundmi tracker until it ‘beeps’ to start pairing.
6. You will receive a Bluetooth pairing request notification on your mobile device.
7. Tap ‘Pair’
8. Name your character.
9. Tap the ‘test’ button to make sure you are paired.

10. “Is your foundmi ringing?” Tap yes or tap try again if it is not.
11. If it is not then follow steps G – J again.
12. If you tap ‘Yes’ you will be redirected back to the main page.
13. Pairing is now complete.

Removing a foundmi tracker
Remove your foundmi tracker from your mobile device
Follow steps 1-3:
1. Tap the ‘I’ icon in the top left corner of the character card.
2. Tap “trash can” icon in the top corner.
3. Tap “delete” to remove the foundmi from your mobile device.

Finding Function
Find your foundmi tracker from your mobile device
Follow steps 1-2:
Make sure that the find button is green on the character card, if it is gray it is out of range.
1. Tap the ‘find it’ button your foundmi tracker should start ringing.
2. Tap “stop” button once you have found your foundmi tracker.

Find your mobile device using your foundmi tracker
Follow steps 1-2:
1. Double click the button on the foundmi tracker .
2. Once you have found your mobile device tap ‘dismiss.’
Edit a foundmi tracker
Follow steps 1-2:
1. Tap the ‘i’ icon in the top left corner of the character card.
2. Tap “pencil” icon in the center to change the name.