Onnto 2.5" SATA HDD Enclosure User manual

Version 02
2.5" SATA HDD Enclosure
Speedy Data Transfer and Flexible Connectivity
User’s Manual
The product information provided in this manual is subject to change without prior
notice and does not represent a commitment on the part of the vendor. The
vendor assumes no liability or responsibility for any errors that may appear in this
manual
Copyright 2007, Onnto Corporation. All rights reserved.

Version 02
2.5” SATA HDD Enclosure
User’s Manual
Introduction ..................................................................................................3
Important Reminders for all Enclosures .......................................................3
Getting Started.............................................................................................4
System Requirements..................................................................................4
Installing the 2.5” SATA HDD.......................................................................5
Connecting the Enclosure to a Computer.....................................................9
Notices and Classifications ........................................................................12

Version 02
Introduction
Thank you for your purchase of the 2.5” SATA to eSATA/USB 2.0/FireWire (800)
Hard Disk Drive (HDD) Enclosure. Your 2.5” SATA HDD Enclosure offers fast
and reliable data transfer. The groundbreaking DuoLink 2-in-1 eSATA/USB
connector combines eSATA and USB 2.0 connectivity in a single port.
Proper installation, care and use, as described in the User’s Manual will ensure
trouble-free use and prolong the life of your 2.5” SATA HDD Enclosure.
Important Reminders for all Enclosures
•The main circuit board of the HDD enclosure is susceptible to static
electricity. Proper grounding is required to prevent electrical damage to
the enclosure or other connected devices, including the computer host.
Always place the HDD enclosure on a smooth, flat surface and avoid all
dramatic movement, vibration and percussion.
•Do NOT allow water to enter the HDD enclosure.
•Avoid placing the HDD enclosure close to magnetic devices (such as a
mobile phone), high-voltage devices (such as a hair dryer), or near a heat
source (such as on the dashboard of a car or any place where the
enclosure will be subject to direct sunlight).
•The operating system may NOT detect the HDD enclosure if it does not
support the interface of your HDD enclosure. If so, installation of an
appropriate driver on the host computer is required.
•Ensure that only a 9.5mm high 2.5” HDD is used in the enclosure. The
Enclosure will not function if an older model HDD with a different thickness
is used. Additionally the enclosure and other equipment may be
damaged.
Please thoroughly read and follow the instructions provided in this
manual. Failure to do so may result in damage to the enclosure and
any or all of the connected devices.

Version 02
Getting Started
This manual provides installation and assembly instructions for the 2.5” SATA
Hard Disk Enclosure. Please review the package contents before installing an
HDD or assembling the 2.5” SATA HDD Enclosure.
eSATA/USB2.0/FireWire800 Model Rear Panel Package Contents
•Enclosure x 1
•USB cable x 1
•IEEE1394b cable x 1
•eSATA cable x 1
•Quick Start Guide
•HDD Fastening Screws x 4
•Rubber Footpads x 8
•AC Power Adapter
eSATA/USB2.0/FireWire400 Model Rear Panel Package Content
•Enclosure x 1
•USB cable x 1
•IEEE1394a cable x 1
•eSATA cable x 1
•Quick Start Guide
•HDD Fastening Screws x 4
•Rubber Footpads x 8
•AC Power Adapter
System Requirements
PC
•266MHz or faster CPU (Microsoft Vista requires a minimum 800MHz
CPU)
•64MB of RAM (Microsoft Vista requires a minimum 512MB of RAM)
•Microsoft Windows 2000, XP, 2003
•One available USB 2.0, eSATA, IEEE1394a or IEEE1394b port (Upon
model)
Mac
•Macintosh PowerPC or Intel Core Duo processor
•64MB of RAM (Mac OS X 10.4 requires 256MB of RAM)
•Mac OS 9.X or higher (PowerPC) / Mac OS X 10.4 (Intel Core Duo)
•One available USB 2.0, eSATA, IEEE 1394a or IEEE1394b port (Upon
model)

Version 02
Installing a 2.5” SATA HDD
Install a 2.5” SATA HDD in the enclosure by completing the following steps.
1) Remove the screw from the rear panel using a Phillips screwdriver.
2) Carefully remove the rear panel from the enclosure.
3) Carefully slide the bottom panel out of the enclosure housing.

Version 02
4) Remove the screw from the control board by loosening the plastic caps.
5) Gently slide the HDD into place.
6) Fasten the HDD to the base using a Phillips screwdriver and the (4)
screws included in the package.
7) Align the edges of the HDD platform with the integral rails and carefully
slide the assembled platform into the enclosure housing.

Version 02
8) Ensure that the LED indicator is properly aligned with the opening on the
front panel of the enclosure.
9) Reassemble the enclosure by replacing the (2) screws removed in step 1.
10)Fasten the last (1) screw to reattach the bottom panel.
11)Attach the four (4) footpads included in the package to the bottom of the
enclosure.

Version 02
The HDD is now installed and the enclosure is ready for connection to a
computer.

Version 02
Connecting the Enclosure to a Computer
Complete the following steps to connect the enclosure to a host computer.
1) Connect the AC/DC power adapter; ensure that the green LED indicator is
active. The LED indicator will blink during data transfer.
2) Insert the eSATA, USB, IEEE 1394a or IEEE 1394b connector into the
corresponding port.

Version 02
The DuoLink 2-in-1 eSATA/USB connector combines eSATA and USB 2.0
connectivity in a single port. The DuoLink accommodates both USB and eSATA
connectors. To transfer data via USB, connect a USB cable to the enclosure. To
transfer data via eSATA connect an eSATA cable to the enclosure.
USB cable
eSATAcable
3) Insert the eSATA, USB, IEEE 1394a or IEEE 1394b connector into an
available port on the computer.

Version 02
Notes:
•Any cable (eSATA, FireWire, or USB 2.0) inserted before the enclosure is
powered on has priority over the other cables and will be the primary
connection method, i.e.: If the enclosure is connected via FireWire 800
before powering on the enclosure, data will be transferred via
FireWire800.
•The enclosure should only be connected to a computer via one interface
at a time. Connection of the enclosure to a computer via two or more
interfaces is not recommended.
•The enclosure supports FireWire bus power. The enclosure can be
powered via the FireWire bus without use of an AC adapter.

Version 02
Notices and Classifications
FCC-B Radio Frequency Interference Statement
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.