orfit RAYCAST 33168 User manual

Page 1 of 2
INSTRUCTIONS FOR USE
RAYCAST® HIGH PRECISION
BASE PLATE-TO-COUCH TOP
FIXATION DEVICES
LOXON™ IN PLASTIC FOR HP
SYSTEM ON EXACT® COUCH
TOPS
Article No. : 33168
A. GENERAL PRODUCT INFORMATION
The product referred to in these instructions is a device used to
connect RAYCAST HP base plates to an Exact® couch top.
This product may only be used in combination with
immobilisation masks produced by Orfit. Orfit prohibits the use
of unauthorized third-party products in conjunction with its own
products.
B. PRODUCT DESCRIPTION
LOXON IN PLASTIC for HP is designed for reproducible
positioning and stable fixation of Orfit base plates 32110 (HP
Base Plate in CFL) and 35751N (HP Base Plate in HPL) on any
couch with Exact® indexing capabilities. Information on these
other parts can be found in the respective ‘instructions for use’
and on www.orfit.com.
C. PARTS LIST
Article number
Description
pieces
33168/1
Set of the fixation devices
2
29053/1/5
Nylon screw M6 x 16
2
32181/2
O-ring, 17 x 5
2
D. FIXATION TO BASE PLATES
Fixation to the 32110 and 35751N base plates
LOXONconsists of two identical pieces that are mounted on
both sides of the base plate as shown below:
Place both parts 33168/1 over the side holes
Screw the two nylon screws into the holes
When both parts are fixed, the base plate is ready to be
installed on the treatment couch
The two parts of LOXON are mounted on the Orfit Industries
base plate with the M6 x 16 screws supplied in the package.
Always mount the fixation devices on the base plate before
installing the base plate on the couch.
Part 2
Part 1

Note:
It is prohibited to make alterations to this text without prior approval from Orfit Industries.
RAYCAST® and EXACT® are registered trademarks of Orfit Industries. LOXON™is a trademark of Orfit Industries.
Page 2 of 2
www.orfit.com
Ref. No. 50106
VERSION 1
LAST UPDATE: 02/04/2021
REVISION DATE: 02/04/2023
E. STORAGE
Always store the product in a safe place to prevent it from
getting damaged.
Store the product between +10°C (50°F) and 40 °C (122°F).
F. PROPERTIES
Physical Properties
Dimensions (1 item): L 35 mm x W 20.5 mm x H 27.5 mm
L 1.38” x W 0.81” x H 1.08”
Weight (1 item): 0.01 kg
0.02 Ibs
Mechanical Properties
The LOXON IN PLASTIC is made of POM. This provides the
necessary stability to get accurate patient positioning even
under frequent use.
Dosimetric Properties
Because of the high density of the POM material, do not use in
the path of the beam.
G. STORAGE
Always store the product in a safe place to prevent it from
getting damaged.
H. MAINTENANCE AND WASTE MANAGEMENT
This product can be cleaned and disinfected by means of soapy
water or an isopropanol based disinfectant, applied with a soft
cloth. If unsure about the cleaning fluid, do not use. Never use
aerosol sprays, corrosive cleaning agents, solvents or abrasive
detergents.
Periodic checks of the products should be done to insure the
parts are not worn and require repair or replacement. Do not
attempt to make repairs yourself, but contact your distributor
if there are any questions or concerns.
The product can be disposed of with household waste.
I. ADDITIONAL INFORMATION
For additional information such as distributor contact
information, product brochures, Safety Data Sheets and
regulatory information, please visit our website www.orfit.com.