Vintage view Vino Flex Series User manual

Vino Series Flex
Installation Instructions for Vino Series Flex (SKUTKTKTKT)
• (2) Backer Strips (unique neck
and base for Vino Pins)
• (6) mounting hole caps
Parts List
Important Note: These installation instructions are only for attaching the Vino Series Flex (for Pins or Rails) mounting
system into solid wood, plywood surface, or drywall with a minimum thickness of ½ inches (12.7mm).
Figure A
Figure B
1. Identify Neck and Base Pieces
(Pins option only):
The neck piece of the Vino Pins features a narrower divot and
corresponds to the Backer Strip with the higher of the offset
wine rack mounting holes.
• (2) Plastic couplers
• (4) spiral drywall anchors
• (6) screws
• (2) toggle bolts
• (18) Vino Series screws
• Phillips head screw driver
• Level
• Pencil
Required Tools
• Tape measure
• Drill
• Handy friend (always helps)
2. Assemble Pins/Rails to Strip
Insert one Vino Series screw through the back of either the
Base or Neck strip and thread the first Vino Pin or Rail until
tight against the surface of the strip. Repeat until all Pins or
Rails are attached.
3. Choose Bottle Direction
(Pins option only)
Decide if you want the necks of the bottles facing left or
right then identify the neck strip (the one with the assem-
bled Pins offset upward).
for Vino Pins
for Vino Rails

Instructions
Figure D
Figure C
4. Lay out Wall
Starting at least 2 ¾” (70mm) from adjacent wall
or other obstructions, mark the centerline of the first
Backer Strip. From there, measure 7 ½” (190.5mm) for
Pins and 2 ½” for Rails (63.5mm) to centerline of the
second Backer Strip.
5. Mark Mounting Hole
Locations:
Hold one Backer Strip (careful to note if it’s the Base or
Neck for Vino Pins options) in place against the wall,
centered on the first mark at your preferred distance
from floor. Ensure the Strip is plum using a level and
mark hole locations with a pencil (Figure B). Backer
Strips can be installed on angles up to 45 degrees
(figure C).
Set strip aside.
PRO TIP: When installing Flex at an angle, the tops of
the Backer Strips will not remain flush. For Vino Pins,
ensure the Pins on the Neck side are offset 5/8” above
the Base side. For Vino Rails, ensure the Rails remain
level.
6. Check for Wood Studs
Drill 1/16” (1.5mm) pilot holes at marked locations to
check for studs or wood backing.
7. Drill Mounting Holes
If Drywall: For the lower two holes us a Phillip’s
head screw driver to insert spiral drywall anchors into
wall until it is flush with the surface. For the top mount-
ing point, drill a 13/23” (10.3mm) hole for toggle
bolt.
If wood or stud: Skip to next step.

Instructions
Figure E
8. Hang the Backer Strip
If drywall, remove the expanding nut from toggle
bolt and insert through the top mounting hole on your
Backer Strip.
With the wings of the nut oriented to fold toward the
bolt head, thread the expanding nut onto the bolt so
the tip of it starts to protrude form the end of the nut.
Hold the strip so the toggle bolt aligns with the top
mounting and gently push the nut through the wall (Fig-
ure D). Ensure the wings have fully expanded on the
backside of the wall and gently tighten, verifying the
necks remain level. Secure the rest of the strip through
the bottom two mounting holes with provided screws.
Fully tighten the toggle bolt.
If wood, use provided screws and install the Backer
Strip to the wall at the marked mounting hole locations.
9. Hang the Next Backer Strip
Repeat steps 5-8 with the second Backer Strip, center-
ing it horizontally with the second mark on your wall
from Step 4 and ensuring the tops of the strips even
with each other.
10. Install Mounting Hole Caps
Press supplied mounting hole caps into the open holes
of the face of each Backer Strip.
11. Add wine
Only the good stuff.
Maintenance and Care:
Vino Series wine racks are backed by a lifetime warranty. They should be regularly checked for tightness. Should any piece
to be found to be loose, tighten by hand until secure. If the face of the wall surface shows signs of breakage, discontinue use
immediately until the wall may be adequately repaired. Vino Series products may be cleaned with a damp cloth and mild
dish soap — abrasive pads or steel wool should NOT be used as they will damage the finished surfaces of the parts.
Need more help? Visit VintageView.com