Outline UB-ARN215CX User manual
USER MANUAL
UB-ARN215CX
U-Shape bracket
OUTLINE S.R.L.
Via Leonardo da Vinci, 56
25020 Flero (Brescia) Italy
Tel.: +39 030.3581341
Fax +39 030.3580431
www.outline.it
2
SAFETY REGULATIONS
Please read this manual carefully and in its
entirety. It contains important information regarding
safety issues, including guidelines for general
safe use of rigging systems as well as advisories
on government regulations and liability laws. The
suspension of large, heavy objects in public places
is subject to numerous laws and regulations at
the national/federal, state/provincial, and local
levels. The user must assume the responsibility for
making sure that the use of any rigging system and
its components in any particular circumstance or
venue conform to all applicable laws and regulations
in force at the time.
GENERAL SAFETY RULES
• Carefully read this manual in all its parts
• Respect the working load limits and maximum
congurations of the elements and of any third-
party component (such as suspension points,
motors, rigging accessories, etc...)
• Do not incorporate any accessory not provided
by Outline; all damaged or defective components
must be replaced only by equivalent parts
approved by Outline
• Ensure personnel health and safety, ensure that
no one is standing below the system during the
installation, ensure that all personnel involved in
the installation are equipped with personal safety
devices
• Always double check that the elements are
correctly connected before suspending the
system.
The rigging elements are easy to use, however the
installation shall be carried out only by qualied
personnel that are familiar with the rigging
techniques, safety recommendations and with the
instructions described in this manual.
All mechanical components are subject to wear and
tear over prolonged use as well as corrosive agents,
impacts or inappropriate use. For this reasons
users have the responsibility to adopt and adhere
to a schedule of inspections and maintenance.
Key components (screws, connecting pins, welded
points, rigging bars) must be inspected before every
use. Outline strongly recommends to carefully
inspect the system components at least once a
year, reporting in a written document the date, the
name of the inspector, the points checked and any
anomalies discovered.
DISPOSAL OF WASTE MATERIALS
The product is designed and manufactured
with high quality materials and components,
which can be recycled and reused. When this
symbol of the crossed “wheelie” bin is attached
to a product, it means that the product is
covered by the European Directive 2012/19/EU
and successive amendments. This means that
the product must NOT be disposed of with other
household-type waste.Users are responsible for
the disposal of their electric and electronic
equipment, consigning it to an approved disposal
facility. For further information on where it is
possible to send equipment for recycling, contact
your local distributor. Correct disposal of the old
product will help to prevent potential negative
consequences for the environment and people’s
health.
CONFORMITY AND WARRANTY
All Outline electro-acoustic and electronic
devices are in conformity with the
provisions of EC/EU directives (as stated
in our CE declaration of conformity).
The CE declaration of conformity is attached to the
product warranty certicate and is shipped with
the product.
OUTLINE S.R.L.
Via Leonardo da Vinci, 56
25020 Flero (Brescia) Italy
Tel.: +39 030.3581341
Fax +39 030.3580431
www.outline.it
3
INSTRUCTIONS
UB-ARN215CX is intended to safely support
Monaco 215 CX and Arena, any other use (including
suspending more speakers or adding more load
by placing weight on the loudspeaker itself, etc...)
is absolutely forbidden.
This bracket allows to mount and set the
loudspeaker cabinet to various angles. It can be
mounted directly on wall, ceiling or any other suitable
surface, or even on a truss using a clamp.
1. Remove the KERL M10 from the bracket
simply by unscrewing the withknob,
2. Attach the clamping area to the rail system’s
rst hole and lock it with the appropriate ring
nut provided by Outline (circled in red ). Use
the wrench (#17) to tighten it,
Tools required:
• Wrench size #17
OUTLINE S.R.L.
Via Leonardo da Vinci, 56
25020 Flero (Brescia) Italy
Tel.: +39 030.3581341
Fax +39 030.3580431
www.outline.it
4
3. Fix the bracket to wall, ceiling or suitable structure. There are ve mounting holes
for this purpose. If you are using the clamp, we suggest you use the central hole.
Please Note that the screws for wall mounting are not provided.
4. Remove the pin to move and open the arm,
5. Attach the cabinet to the bracket, rst
insert the lower part with the pole
into the bottom hole of the cabinet,
6. Close the other side of the bracket. It is
very important that the buffer for ange
positioning is inside the rail as shown
by the arrow in the gure. Then screw
the Kerl M10 knob into the threaded pin,
7. Set the angles as desired and tighten the
withknobs.
Outline carries out on-going research for product improvement. New materials, manufacturing methods
and design upgrades are introduced to existing products without prior notice as a routine result of this phi-
losophy. For this reason, any current Outline product may differ in some aspect from its description, but will
always equal or exceed the original design specications unless otherwise stated.
© Outline 2021
Operating manual product code: Z OMUB-ARN215CX
Release:20210914
Printed in Italy
Table of contents
