Ove Decors TUVA User manual

p. 1
OVE INTELLIGENT TOILET
Model TUVA
INSTRUCTION MANUAL
Thank you for choosing OVE INTELLIGENT TOILET. Please read and understand this entire manual
before attempting to assemble, operate or install this product.

p. 2
SAFETY NOTICE ............................................................................................. p.3
WARNINGS ...................................................................................................... p.4
PART LIST ........................................................................................................ p.5
INSTALLATION INSTRUCTIONS ................................................................. p.6-8
FIRST TIME USE .............................................................................................. p.9
CONTROLS DESCRIPTION ..................................................................... p.10-11
FEATURES .................................................................................................... p.12
INTELLIGENT FEATURES ............................................................................. p.13
CLEANING THE FILTER ................................................................................ p.14
LONG TERM STORAGE ................................................................................ p.15
BATTERY MAINTENANCE ............................................................................ p.15
SPECIFICATION SHEET ............................................................................... p.16
MAINTENANCE & CONSUMER RESPONSIBILITIES ................................... p.17
LIMITED 1 YEAR WARRANTY ....................................................................... p.17
INFORMATION ABOUT YOUR WARRANTY COVERAGE ............................ p.17
NOTES ON WARRANTY ................................................................................ p.17
FOR WARRANTY SERVICE .......................................................................... p.17
INSTALLATION PICTURE .............................................................................. p.18
CONTACT US ................................................................................................. p.19
CONTENT

p. 3
SAFETY NOTICE
1. It is forbidden to disassemble toilet by yourself.
2. Please do not set this product in a wet place, because it is an electronic product. If set in the
bathroom, please insure that there is proper air ow.
3. Please insure that the product is set more than 0.6 meter away from the bathtub.
4. Please make sure electric power is AC 110V +/- 10%. Ensure the electrical socket can bare a load
of 1500W power (or else it can cause re or electrical shock).
5. Please make sure the electrical source is well grounded.
6. Please do not put any water or detergent on the product or its electrical plug.
7. Do not touch the electrical plug with a wet hand (or else it can cause re or electric shock).
8. Do not use the product if it has these following problems. When any of the following problems occur,
turn o󰀨 the electricity and close the water valve.
• Water leaking from the pipe or the main body.
• Crack or breakage
• Abnormal sound or smell of the product
• Smoke coming out from the product
9. Keep any ame or ammable products away from the toilet.
10. Please do not step on the toilet seat, the seat cover, the main body, or put anything heavy on the
product. Otherwise, the product may break and may cause injury or the product may break and may
cause indoor ooding.
11. Please do not put your nger or anything else into the outlet of the drying blower.
12. Please do not touch or cover the drying blower outlet with clothes, or it may lead to burn injury or
electric shock.
13. Please do not tightly bend or press the exible supply hose, or it may lead to water leakage or it may
decrease the water pressure.
14. Please clean the product with soft cleaning products.
15. Please do not use any harsh detergents to clean the product.
16. Please do not throw anything other than toilet paper into the toilet or it may lead to blockage and
indoor ooding.
17. Please be careful to not let objects like a comb, toothbrush or other stu󰀨 fall into the toilet.
ATTENTION!
BEFORE INSTALLING THE PRODUCT, YOU MUST READ AND
UNDERSTAND CAREFULLY ALL BELOW WARNINGS.

p. 4
WARNINGS
Do not leave the
toilet exposed to the sun.
May cause yellowing or
color fading.
Direct sunlight a󰀨ects the
good functioning of the
remote.
To prevent against power
surge damages, make
sure the ground is working
in the power socket.
Radio or transmitting
devices may interfere with
the toilet’s remote control
functions
If you do not plan to use
the toilet for a long time,
close the inlet water valve
and unplug the toilet.
If the power cut o󰀨 during
washing and the nozzle is
still out: Do not push it back
manually, it will revert to its
resting position once the
power is back ON.
Do not use DC current.
Only AC 110V with load
capacity over 1500W are
accepted.
If power cuts o󰀨 during
nozzle self-cleaning, the
water will continue to ow
out. Manually close the
inlet water valve of the
toilet until power comes
back ON.
Do not expose the toilet to
freezing temperature. This
will void the warranty and
damage the piping.
Be careful not to spill water
on the top of the toilet:
Electronics are located
under the plastic cover.
Do not lean on the cover.

p. 5
PART LIST
Item Qty #
ALight Indicator Panel 1 99TOI0115OU
BWater Inlet 1 --
CSide Control Panel 1 99TOI0117OU
DWater Supply Hose 1 99TOI0118OU
EWater Filter 1 99TOI0138-OU
FInlet Fitting & Valve 1 99TOI0120OU
GSeat 1 99TOI0121OU
HRemote Receiver 1 --
IBattery Enclosure 1 99TOI0123OU
JManual Flush Button 1 99TOI0124OU
KNozzle 1 99TOI0125OU
LSeal ring 1 99TOI0126OU
MRemote 1 99TOI0127OU
NFlow Regulator 1 99TOI0139-OU
A
B
C
D
N
F
K
J
I
H
G
M
L
Clockwise - Higher ow
Anti-cloclwise - Lower ow
E

p. 6
Position correctly the two xing bolts of the oor drain. Follow
manufacturer’s recommendations.
Install the oor drain cover connector according to the manufacturer’s
recommendations.
To unplug the water tube:
1) Remove the blue clip.
2) Push the ring down with your ngernail.
3) While still pushing the ring down, gently pull-out the water tube.Unplug the cord.
Unplug the electrical cord and the water tube before completely pulling away the
toilet seat.
Remove the seat from the ceramic base. Simply pull the
seat up gently. Be careful, there are wires that need to be
disconnected before you can remove the seat completely
(see step #2).
INSTALLATION INSTRUCTIONS
1 2
B
A
2
1
3
2A 2B
3 4
NOT SUPPLIED

p. 7
Reconnect the electrical cord. Make sure both ends are well aligned.
With care, re-install the seat on the ceramic base. Make
sure no wires get squeezed or tangled.
Using a ratchet, tightly screw the nut to the xing bolts.
Insert the ring gasket under the toilet.
Position the toilet on the oor drain, making sure the xing bolts are
aligned with the toilet’s holes.
Reconnect the water tube:
1) Gently, but rmly push the tube inside the hole.
2) Re-insert the blue clip.
2
1
5 6
7 8
9 10
INSTALLATION INSTRUCTIONS

p. 8
Apply silicone around the base of the toilet.
Wait for 24h for it to dry.
Connect the ow regulator outlet to the toilet’s water inlet with the supplied ex-tube.
Connect the water inlet tting to the water supply. Then connect the valve. Finally connect the ow regulator to the valve.
11
12
INSTALLATION INSTRUCTIONS
13
24h

p. 9
FIRST TIME USE
2
3
1Open the water supply inlet valve.
4
1
Plug the toilet in the power socket.
2
The toilet’s blue light will start blinking.
The blinking light indicates that the wash tank is lling with water, a sensor in the toilet will stop the
lling process automatically after around 3 minutes when the tank is full of water.
After the wash tank is lled with water, the indicator light will stop blinking.
3
The toilet will turn ON automatically. Once the beeping sounds and the ashing light have stopped,
the toilet is ready for use.
4
Notice:
• Warming up the toilet seat will take about 3 minutes.
• Warming up the bidet cleaning water will take about 3 min.
• Leave the power continuously ON to assure all functions are ready for anytime use.
• If the toilet is not used for 24h, it will enter in ECO MODE.

p. 10
CONTROLS DESCRIPTION
SIDE CONTROL PANEL
POWER/ECO:
Press 1 time, it will turn the toilet ON.
Press 2 times, it will activate the ECO MODE.
Press 3 times, it will turn the toilet OFF.
STOP:
Pressing this button will stop any ongoing function.
BIDET/MOVE:
Pressing this button will initiate the Static Bidet Cleaning function. Press it again to change
to the Back-&-Forth Bidet Cleaning function.
*The Bidet refers the 5 water jets function of the nozzle.
SPRAY/MOVE:
Pressing this button will initiate the Static Spray Cleaning function. Press it again to change
to the Back-&-Forth Spray Cleaning function.
*The SPRAY refers the 1 water jet function of the nozzle.
SEAT
SENSOR
LIGHT INDICATOR PANEL
POWER ECO MODE WATER
TEMP
SEAT
TEMP
POWER indicator:
The light will turn RED
when the toilet is powered
ON.
The light will turn o󰀨 when
the toilet is powered OFF.
ECO MODE indicator:
The light will turn YELLOW
when the ECO MODE is
active.
The light will turn o󰀨 when
the ECO MODE is not
active.
WATER TEMP indicator:
Below are the di󰀨erent
colors the light takes
depending on the current
setting:
Room Temp = Light OFF
34C (93F) = GREEN
37C (99F) = ORANGE
40C (104F) = RED
SEAT TEMP indicator:
Below are the di󰀨erent
colors the light takes
depending on the current
setting:
Room Temp = Light OFF
34C (93F) = GREEN
37C (99F) = ORANGE
40C (104F) = RED
SEAT SENSOR
indicator:
The light will turn GREEN
when the Seat Sensor is
active.
The light will turn o󰀨 when
the Seat Sensor is not
active.
BEEPING SOUNDS DIRECTIONS
1X BEEP = The toilet will give out one beeping sound every time it successfully receives a command from the Remote
Control.
2x BEEP = The toilet will give out two beeping sounds every time it has successfully received a command, but cannot
execute it. For example, if the Seat Sensor is not active and the user presses the BIDET/MOVE button, the toilet will beep
two times because the bidet function cannot be active if the seat sensor is not active.
3x BEEP = The toilet will give out three beeping sounds every time it has successfully received a command, but the
function the user is trying to adjust has already reached its maximum or minimum setting.
BEEPING for Temperature levels:
While adjusting the temperature for the Bidet/Spray water, the Seat or the Drying Air, the toilet will beep as follow to
indicate which temperature has just been set:
-ROOM TEMP = 1x long beep
-34C (93F) / 35C (95F) = 1x short beep
-37C (99F) / 45C (113F) = 2x beep
-40C (104F) / 55C (151F) = 3x beep