Oxgard Praktika K-01 Instruction sheet

Installation
guidelines
www.oxgard.com
[email protected]
Tel: [phone]
Praktika K-01 card collector

Installation guidelines 3
Contents
1. Basic specifications.................................................................................. 5
2. Product design.......................................................................................... 6
3. Safety requirements.................................................................................. 8
4. Installation of card collector..................................................................... 9
4.1. Required equipment .......................................................................... 9
4.2. Installation of card collector ............................................................. 9
6. Inversion of the LED panel board.......................................................... 27
7. Connecting card collector ...................................................................... 29

Praktika K-01 card collector 4
List of abbreviations
PS –power supply
ACS –access control system
OD –operating device
NC –normally connected
NO –normally opened
Software FW v1.52

Installation guidelines 5
1. Basic specifications
Table 1. Basic specifications
Specification
Value
Dimensions (WхHхL), mm
200х1045х200
Weight, kg
24
Temperature range,, ºС:
-operation
-transportation and storage
+1…+40
+1…+40
Atmosphere relative humidity, no more than %
80
Supply voltage, V:
- nominal
- working
12
8…18
Average current in standby mode * A
0,2
Maximal current *, A
1,5
Maximal dimensions, mm
155х40х55
Capacity of cards, pcs
More than 500
Lifetime, years
8
* - values mentioned at a nominal supply voltage
The manufacturer reserves the right to change the packaging, specifications and appearance
without notice

Praktika K-01 card collector 6
2. Product design
Fig 1. General view of card collector
The housing is made of brushed stainless steel. In front of the
housing there is a hatch with lock for quick access to collected cards and to
the board where PS, OD and ACS cables are connected. The hatch
includes a card storage device. The lower part of housing is equipped with
a hole for cables inlet.
Overall dimensions of the card collector are shown in Fig. 2

Installation guidelines 7
Fig 2. Dimensions
ATTENTION (!) Card reader is not included in the delivery set.
Customer can choose reader model suitable for the existing system.
The reader is mounted on a universal adjustable bracket, located
under the top cover of the card collector. This solution provides maximum
flexibility for installation and connection of the card reader.

Praktika K-01 card collector 8
3. Safety requirements
CAUTION! Failure to comply with the safety requirements specified in
this section may result in damage to human life and health, total or partial
loss of workability of products and (or) auxiliary equipment.
CAUTION! The producer disclaims any liability for damage to human life
and health, total or partial loss of workability of products and (or) auxiliary
equipment for non-compliance of the safety requirements specified in this
section, as well as terminate the product warranty.
IT IS NOT ALLOWED TO:
Set the power supply inside the card reader housing, as this could
lead to electric shock to persons;
Set the card collector other than in dry and heated places;
Apply chemically aggressive cleaning detergents as pastes and
liquids.

Installation guidelines 9
4. Installation of card collector
CAUTION: The card collector should be installed securely to avoid
swinging and (or) overthrow during operation. In case of installation on
the low strength floors - take action to strengthen the floor at the
installation site.
Before verify of operability of the card reader carefully read this section of
the Regulations.
4.1. Required equipment
Tools used for card reader mounting:
Electric perforator;
20mm diameter carbide drill for drilling holes in the floor for anchors
(recommended anchor - SORMAT PFG LB 12-50);
S10 wrench for hexagon socket head screws;
slotted screwdriver;
plumb line or level;
steel liner for card collector alignment
side cutters
4.2. Installation of card collector
4.2.1. Prepare a horizontal surface at the installation site of card
collector.

Praktika K-01 card collector 10
4.2.2. Prepare cable channel from the site to the installation site of
PS, RC, as well as, if required, to the point of ACS and fire alarm
connection.
4.2.3. According to the dimensions shown in Fig. 3, prepare three
20mm diameter holes in the floor for anchors (the location of the mounting
holes regarding to the dimensions of the card reader is shown in Annex 2).
Depth of the hole should exceed the length of the anchor for more than
5mm. Put the anchors in the holes.
4.2.4. Cable routing is carried out through 32 mm diameter hole (Fig.
3) in the lower plate of the card collector.
Fig 3. Linkage dimension
4.2.5. Open the box, unpack the product and check for
completeness.
4.2.6. Route PS, OD and ACS cables into cable conduit.
3 Hole