Ozito SNG-2050 User manual
ELECTRIC
STAPLE
NAIL GUN
8MM - 14MM
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 230-240V ~ 50Hz
Power: 45W
Impact Rate: 30/min
Staple Size: 8-14mm, Type 50
Nail Size: 15mm, C1 Brad
Magazine Capacity: 80 Pcs
Weight: 0.73kg
SNG-2050
WHAT’S IN THE BOX
Staple Nail Gun
ozito.com.au
Staples x 1500
Nails x 100
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1. LOADING STAPLES
1 Hold the tool upside down.
This staple nailer only accepts T50 staples. Other types of staples,
including paper staples, will jam the unit.
3 Insert a row of staples into
the opening behind the
nose piece.
2 Squeeze the magazine latches on either side of the tool and pull the
magazine out of the tool.
4 Push the loaded magazine back into the unit until it clips into place.
a
b
Note: Rows of staples longer than 120mm do not t in the staple nail
gun.
KNOW YOUR PRODUCT SETUP & PREPARATION
1 Safety Striker Pin
2 Nose Piece
3 Magazine Window
4 Trigger
5 Sure Grip Handle
6 Magazine Latch
7 On/Off Switch
8 Power Cord
ELECTRIC STAPLE NAIL GUN
1
9 10
3 5 72 4 6 8
9 Staples x 1500 10 Nails x 100
ACCESSORIES
CAUTION! ENSURE THE TOOL IS SWITCH OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING THE FOLLOWING PROCEDURES.
2. LOADING NAILS
1 Hold the tool upside down.
This staple nailer only accepts 18 Gauge C1 Brad nails up to 15mm in
length. Other types of nails will jam the unit.
3 Insert a row of nails into the opening behind the nose piece.
Be sure to align them to the side marked with a nail marker so that
the nail head is against the internal groove.
2 Squeeze the magazine latches on either side of the tool and pull the
magazine out of the tool.
4 Push the loaded magazine back into the unit until it clips into place.
a
b
3. CONTROLS
Switching On and Off
1 To supply the tool with power,
push the power switch to the
“I” position.
2 To turn off, push the power
switch to the “O” position.
CAUTION! THE POWER SUPPLY FOR THIS PRODUCT
SHOULD BE PROTECTED BY A RESIDUAL CURRENT
DEVICE (RATED AT 30MA OR LESS).
4. OPERATING THE STAPLE NAIL GUN
Firing a Staple or Nail
2 Place the staple nail
gun against the work
surface so that the
nosepiece of the tool
is where you want the
staple/nail to be located.
Push the safety striker
pin and nosepiece down
onto the surface to be
fastened.
A staple or nail will only re when the trigger is pressed if the safety
striker pin is pushed against the material to be fastened.
1 Switch the on/off switch into
the on position.
3 To re the staple nail gun,
squeeze the trigger.
SNG-2050
5. TROUBLESHOOTING
OPERATION
Jammed Staple Nail Gun
2 Using a pair of pliers, remove
any jammed staples or nails.
3 With the magazine still open,
tap the safety striker pin
against a surface to dislodge
any loose staples.
Note: Be careful not to bend the end of the magazine. If this occurs the
unit will be inoperable.
1 Squeeze the magazine latches on either side of the tool and pull the
magazine out of the tool.
a
b
Power tools that are no longer usable should not be
disposed of with household waste but in an environmentally
friendly way. Please recycle where facilities exist. Check
with your local council authority for recycling advice.
Recycling packaging reduces the need for landll and raw
materials. Reuse of recycled material decreases pollution in
the environment. Please recycle packaging where facilities
exist. Check with your local council authority for recycling
advice.
MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
STAPLE/ NAIL SELECTION
Common Applications for Staple Length
5/16”
(8mm)
Insulation, Upholstery, Weather Stripping,
Wall Decorations, Crafts, Covering Cornices,
Webbing, Light Fabrics.
3/8”
(10mm)
Insulation, Carpeting, Wire Mesh, Plastic
or Canvas Coverings, Roong Paper, Felt
Stripping, Weather Stripping.
1/2”
(12mm)
Insulation, Carpet Underlay, Porch Screens,
Picture Frames, Wire Mesh, Netting, Roong
Paper, Panelling.
9/16”
(14mm)
Ceiling Tile, Heavy Insulation, Insulation Board,
Trellises, Roong, Carpeting.
Common applications: C1 Brads
9/16”
(15mm)
Trim Moulding, Panelling, Picture Frames,
Model Work, Any Finish Nailing Application.
8
10
12
14
Width
10.6mm
Depth
1.2mm
Front View Side View
Width
2mm
Front View
14
16
1.2mm
T50 STAPLE SIZE
18 GAUGE C1 BRAD NAIL SIZE
8
10
12
14
Width
10.6mm
Depth
1.2mm
Front View Side View
Width
2mm
Front View
15
1.2mm
The SNG-2050 accepts staples with the below measurements
The SNG-2050 accepts nails with the below measurements
• When not in use, the staple nail gun should be stored in a dry,
frost free location, keep out of children’s reach.
• If the housing of the staple nail gun requires cleaning, do not
use solvents. Use of a cloth only is recommended. Never im-
merse any part of the staple nail gun into liquid.
Note: Ozito Industries will not be responsible for any damage or
injuries caused by repair of the staple nail gun by an unauthorised
person or by mishandling.
Read instruction manual
Wear eye protection
Warning
ga
/min
Gauge
Impacts per minute
V Volts Hz Hertz
ac/~ Alternating current W Watts
Regulatory Compliance Mark
(RCM)
SPARE PARTS Tool: Electric Staple Nail Gun
Model No. SNG-2050
How To Order
Available spare parts can be ordered through the Special Orders Desk at any Bunnings Warehouse. If you have any
further questions, please contact Ozito Customer Service on:
Australia: 1800 069 486
New Zealand: 0508 069 486
Tool: Electric Staple Nail Gun
Model No. SNG-2050
STAPLE NAIL GUN SAFETY WARNINGS
GENERAL POWER TOOL SAFETY WARNINGS - PERSONAL SAFETY
ELECTRICAL SAFETY
• Always assume that the tool contains fasteners. Careless handling of the
nailer or stapler can result in unexpected ring of fasteners and personal injury.
• Do not point the tool towards yourself or anyone nearby. Unexpected
triggering will discharge the fastener causing an injury.
• Donotactuatethetoolunlessthetoolisplacedrmlyagainstthe
workpiece. If the tool is not in contact with the workpiece, the fastener may be
deected away from your target.
• Disconnect the tool from the power source when the fastener jams in
the tool. While removing a jammed fastener, the nailer or stapler may be
accidentally activated if it is plugged in.
• Do not use this nailer or stapler for fastening electrical cables. It is not
designed for electric cable installation and may damage the insulation of
electric cables thereby causing electric shock or re hazards.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Donotoperatepowertoolsinexplosiveatmospheres,suchasinthepresenceofammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
notuseapowertoolwhileyouaretiredorundertheinuenceofdrugs,alcoholormedication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
5. Service
a. Haveyourpowertoolservicedbyaqualiedrepairpersonusingonlyidenticalreplacement
parts. This will ensure that the safety of the power tool is maintained.
WARNING! When using mains-powered tools, basic safety precautions, including
thefollowing,shouldalwaysbefollowedtoreduceriskofre,electricshock,personal
injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency,
before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that the power supply
corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.
This tool is double insulated; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to
avoid a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating this
tool. The insulation system is for added protection against injury resulting from a possible electrical
insulation failure within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect
the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or
defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead
not suitable for the power input of the tool or which is damaged or defective may result in a risk of re
and electric shock.
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty.
Warranty excludes consumable parts, for example: staples, nails,
etc.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
1215
Table of contents
Other Ozito Nail Gun & Stapler manuals
