Pacific SilverRay 133 Installation and operation manual

READ THIS BOOK
This operator’s book has important information for the use
and safe operation of this machine. Read this book care-
fully before starting the machine. Keep this book and tell
all operators to read the book. If you do not follow the
instructions, you can cause an injury or damage equipment,
furniture or buildings.
For new books write to:
Pacific
2259 S. Sheridan
Muskegon, MI 49442-6252
Carefully inspect all components to ensure that there is no
concealed freight damage. If such damage is discovered,
file a “CONCEALED DAMAGE REPORT” immediately
with the delivering carrier.
The contents of this manual are based on the latest product
information available at the time of publication. Pacific
reserves the right to make changes or improvements to its
machines without notice.
FOR YOUR CONVENIENCE, RECORD THE FOL-
LOWING INFORMATION:
MODEL_______________________________
SERIAL NUMBER______________________
PART NUMBER_________________________
DATE PURCHASED_____________________
OPERATING & MAINTENANCE
INTRODUCTION INSTRUCTIONS
MODELS
SilverRay 133
SilverRay 170
SilverRay 175
SilverRay 200
SilverRay 205
POLISHERS

IMPORTANT SAFETY INSTRUCTIONS
To assure the safe operation of this machine, you must read and understand all warnings and instructions in this book. If you
do not understand, ask your supervisor.
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE
WARNING: To reduce the risk of fire, electric shock, or injury:
1. You must be trained to operate this machine. This machine is to be operated for its intended use only.
2. Do not operate this machine unless it is completely assembled.
3. Always use a three-wire electrical system connected to the electrical ground. For maximum protection against electrical
shock, use a circuit that is protected by a ground fault circuit interrupter. Consult your electrical contractor.
4. To prevent electric shock, always remove the electrical plug from the electrical outlet before doing any repairs or mainte-
nance and when leaving the machine unattended.
5. To prevent electric shock, keep the machine surface dry. Do not subject to rain. Store the machine in a dry building area.
Clean the machine with a dry cloth only.
6. Machines can cause an explosion when near flammable materials and vapors. Do not use this machine with or near fuels,
grain dust, solvents, thinners, or other flammable materials. Do not use flammables to clean this machine.
7. A qualified or authorized person must do maintenance and repairs.
8. To prevent damage to the power cord, do not move this machine over the power cord. Always lift the power cord over the
machine. Do not pull or carry cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
9. Do not use with damaged cord or plug. If the machine is not working as it should, has been dropped, damaged, left outdoors,
or dropped into water, return it to a service center.
This machine must be grounded. If it should malfunction or break down,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This machine is equipped with a cord having an
equipment-grounding conductor and grounding plug. The plug must be
inserted into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified electrician
or service person if you are in doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with the machine - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician.
This machine is for use on a nominal 120-volt circuit, and has a grounded
plug that looks like the plug illustrated in figure A. A temporary adapter
that looks like the adapter illustrated in figures B and C may be used to
connect this plug to a 2-pole receptacle as shown in figure B if a properly
grounded outlet is not available. The temporary adapter should be used only
until a properly grounded outlet (figure A) can be installed by a qualified
electrician. The green colored rigid ear, lug, or the like extending from
the adapter must be connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permitted by the
Canadian Electrical Code
EXTENSION CORDS
Use only three-wire 12/3 or larger gauge approved extension cords that have
three-prong grounding type plugs and three-pole receptacles that accept the
appliance’s plug. Replace or repair any damaged cords or plugs.
When servicing, refer to authorized person only. Use only identical
replacement parts.
Grounding Instructions
NOTE: Do not use adapters shown in figures B & C in Canada
2

OPERATING PROCEDURES
WARNING! For the safe operation of this machine fol-
low the instructions given in this manual and the training
given by your supervisor. Failure to do so can result in
personal injury and/or damage to machine and property!
DO NOT OPERATE MACHINE IN AN EXPLOSIVE
ENVIRONMENT!
This machine is intended for commercial use.
PREPARATION
To prepare the machine for operation, make sure it is of
correct voltage and properly assembled.
Your new floor machine operates in the normal side to side
motion of a conventional single disc machine. Be prepared
before starting by removing all obstructions or other obsta-
cles in the area to be cleaned. Check the proper application
recommendations and procedures found on the label of your
cleaning or finish container. IF IN DOUBT, CALL
YOUR SUPERVISOR .
WARNING! NEVER USE THIS MACHINE WITH
FLAMMABLE OR EXPLOSIVE MATERIAL!
For Scrubbing or Polishing: Select the correct floor
pad or brush (your supplier can help you). If in doubt, ask
your supervisor.
NEVER OPERATE THE MACHINE WITHOUT THE
FLOOR PAD OR BRUSH INSTALLED!
To properly attach the brush, UNPLUG THE FLOOR
MACHINE, place the handle in the vertical position, then
tilt the machine back until the handle rests on the floor.
Straddle the handle, facing the motor, and grasp the brush
with the block toward you. Place the brush or pad clutch
plate over the three lugs on the motor drive adapter. Twist
the brush right to lock it into position. To remove the brush,
UNPLUG THE MACHINE and follow the same procedure
as above, but by twisting the brush off with a firm jerk to the
left. Remove the brush or pad driver when the machine is
not in use. This will help prevent brush damage and reduce
wobble problems.
OPERATION
Plug the machine’s power cable into a properly grounded
outlet (see Safety Instructions). Next, adjust the handle
height to a comfortable position.
Pull out on the “Watch Dog” Safety Lock button and start
the machine by depressing either the left or right switch
levers.
Both hands should be placed on the handle when the machine
is in operation. The machine will glide sideways over the
floor by a slight raising and lowering of the handle. Raise
the handle slightly to go to the right. Lower the handle
slightly to go left. Releasing the switch lever stops the
machine at once.
MAINTENANCE
AFTER EACH USE: Store the machine in a clean dry
area. Wipe the entire machine and cord down with a clean
cloth. Remove the pad or brush and clean thoroughly. Wrap
the machine’s electrical cord onto the handles and the cord
hook provided. CHECK the cord and plug for nicks, cuts or
damage. Report these to your supervisor for correction.
WARNING! Always disconnect the machine’s electrical
plug from the electrical outlet before performing any
service, maintenance, pad changing or inspection of the
machine.
MOTOR: The motor is lubricated for life under normal
use. No oiling or greasing is necessary. However, if the
machine is used in dusty areas or is used for spray buffing,
the motor should be cleaned. Blowing the motor out with
compressed air or with the exhaust from a vacuum is sug-
gested. Keeping the motor clean will allow the clear pas-
sage of air for ventilation and prevent overheating. If you
have any questions regarding the maintenance of your floor
machine, ASK YOUR SUPERVISOR.
3

SILVERRAY MODELS
4
44
46
45
47
49
48
50
52
55
58
51
53
56
57
59
61
60
53 52
51
62
63
64
54

SILVERRAY Parts List
ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY.
1 W323D Screw, 6-32x1 Pan Hd. 2 41 908004 Handle Cord 1
2 980016 Washer, #6 Ext. Tooth 2 42 509920 Yoke, Handle 1
3 500801 Bracket, Switch Mounting 1 43 504702 Insulator-Switch 1
4 911135 Switch 1 44 962004 Screw, 10-32 x 1-1/4 oval 3
5 508301 Spring 1 45 501520 Tote-A Brush Cap 1
6 507001 Plunger 1 46 502310 Drip Cover, Motor - 13” 1
7 500802 Bracket, Switch 1 502380 Drip Cover, Motor-17”&20” 1
8 962002 Screw, 10-32 x 1/2 Oval Hd. 2 47 501212 Motor Bumper-13” 1
9 504810 Interlock Asm.-Switch 1 501287 Motor Bumper-17”&20” 1
10 962011 Screw, 10-32 x 3/4 Oval Hd. 2 48 508210 Spacer, Drip Cover-13” 1
11 506430 Switch Cover Plate 1 508220 Spacer, Drip Cover-17”&20” 1
12 509821 Washer, Rubber 2 962019 Screws for Spacer 3
13 920005 Nut, 3/8-24 Hex 1 49 509823 Washer, Felt 1
14 505003 Switch Assembly 1 50 501810 Base Frame, Polished - 13” 1
15 505121 Lever, Switch Left 1 501841 Base Frame, Polished - 17” 1
16 505120 Lever, Switch Right 1 501851 Base Frame, Polished - 20” 1
17 920001 Nut, 10-32 Elastic Stop 1 51 962006 Screw, Yoke 2
18 509830 Washer, Handle Tube 1 980002 Lock Washers - 13” Only 2
19 503320 Flange, Strain Relief 1 52 509820 Washer, Fibre - 17”&20” 4
20 505720 Handle Nipple 2 980005 Washer, Wave - 13”/17”&20” 2/4
21 501325 Switch Box, Polished 1 53 507710 Axle, Wheel-13” 1
22 515150 Warning Label 1 507740 Axle, Wheel-17”&20” 1
23 501210 Bumper, Handle 1 54 509710 Wheeel, 3” - 13” 1
24 962003 Screw, 10-32 x 3/4 Pan Hd. 1 509780 Wheel, 4” - 17” 2
25 962006 Screw, 1/4-20 x 1/2 Pan Hd. 4 509781 Wheel, 5” - 20” 1
26 503711 Handle Grip, Grey 2 55 962006 Screw, Yoke Rod 2
501501 Cap, Protective End (Blue) 2 56 487701 Rod, Yoke - 13” 1
27 980015 Washer, #10 Shakeproof 1 508213 Spacers - 13” Only 4
28 508520 Strain Relief-Complete 1 507480 Rod, Yoke-17”&20” 1
502020 Strain Relief-Brass Clamp 1 57 See Page 6 Motor Assembly 1
29 962015 Screw, 10-32 x 3/8 Pan Hd. 1 58 962001 Screw, Clips - 13”/17”&20” 1/3
30 980018 Washer, #10 Countersunk 1 59 502110 Clips, Bumper - 13”/17”&20” 1/3
32 509082 Handle Tube 1 60 980002 Washer, 1/4 Lock 4
33 504420 Cord Hook 1 61 980004 Washer, 1/4 Flat-17”&20” 4
34 502421 Cord Asm.-50 ft. Grey 1 62 962007 Screw, Motor - 13” 4
35 502021 Clamp-Handle 1 962010 Screw, Motor - 17”&20” 4
36 500880 Brace, Handle Support-13” 2 63 501220 Bumper, Base - 13” 1
500840 Brace,Handle Sup.-17”&20” 2 501242 Bumper, Base - 17” 1
37 962009 Bolt, Carriage 5/16-18 x 2-1/2 1 501260 Bumper, Base - 20” 1
38 962005 Screw, 1/4-20 x 3/8 Allen 1 64 508011 Bumper Strap - 13” 1
39 505010 Turn Knob 1 508041 Bumper Strap - 17” 1
40 980007 Washer, 5/16 Flat 2 508051 Bumper Strap - 20” 1

6
MOTOR PARTS LIST for SILVERRAY MOTORS
ITEM DESCRIPTION PART NUMBERS
505210 505299 505274 505249
1/3 HP Motor-115V, 60CY 1 HP Motor-115V, 60CY 1.5 HP Motor-115V, 60CY 1.5 HP Motor-115V, 60CY
Howell #37PD4-3134-1 Baldor #36J378Y799 Baldor #36J378T115 505251 Motor & Gear Assembly
503501 503522 503523 503523
Gear Asm. for 1/3 HP Gear Asm. for 1 HP Gear Asm. for 1.5 HP Gear Asm. for 1.5 HP
11:1 - 1 Planet 10:1 - 2 Planet 10:1 - 3 Planet 10:1 - 3 Planet
A Ring Gear Housing 504202 504209 504209 504209
B Bearing, Ring Gear Housing 902007 902007 902007 902007
C Planet Gear Hsing 504204 504216 504208 504208 D Bearing, Pinion Lower 902006 902005 902005 902005
E Screw-Ring Gear Hs. 960016 (Qty.6)
F Screw, Planet Gear Housing 960017 (Qty.6)
G Motor Cord 908021 908090 908090
H Run Capacitor NA 911235 911236 911305
I Cover,Run Capacitor NA 502374 502374
J Cover, Start Capacitor 502312 502374 502374
K Start Capacitor 911042 911239 911239 911304
L Bolt 960013 960035 960035
M End Bell 502913 502931 502931
N Stator Asm,115V-60C 503106 503125 503131
O Bearing, Motor Top 902003 902003 902003 902003
P Stationary Switch 911043 911251 911251 911306
Q Rotary Switch 911044 911219 911289 911307
R Rotor Assembly 500406 500429 500435
S End Bell-Motor Lower 502916 502927 502927 502927
T Cover, Ring Gear 502314 502317 502317 502317
U Bearing, Upper Gear Housing 504207 902015 902015 902015
V Bearing, Pinion Upper 902005 902005 902005 902005 X Coupling Flexible 502460 502460 502460 502460
Y Spacer 508222 508211 508211 508211
Z Pinion 503507 503510 503510 503510
AA Shaft-Planet Gear 507724 507701 (Qty.2) 507701 (Qty.3) 507701 (Qty.3)
BB Bearing-Planet Shaft 902008 (Qty.2) 902016 (Qty.4) 902016 (Qty.6) 902016 (Qty.6)
CC Gear-Planet 503509 503511 (Qty.2) 503511 (Qty.3) 503511 (Qty.3)

AC MOTOR ILLUSTRATION
WHITE WHITE
BLACK BLACK
GREEN GREEN
MOTOR
HANDLE
SWITCH
(COM)
(COM)
(N.O.)
(N.O.)
POWER
SUPPLY
CORD
HANDLE
CORD
SWITCH
HOUSING
SINGLE PHASE
GROUNDED
POWER SUPPLY
115 VOLTS
60 HERTZ
GROUND
WIRING DIAGRAM

09/04
WARRANTY POLICY
SILVERRAY POLISHER MODELS
The Pacific Polisher has been manufactured, tested and inspected in accordance with specific engineering requirements and is
WARRANTED to be free from defects in workmanship and materials as follows:
Five (5) years parts, One (1) year labor - AC Motor and Gear Unit, except motor switches, capacitors and flex couplings which
have a one (1) year waranty.
Five (5) years parts, One (1) year labor - Castings
One (1) year parts and labor - All other components unless excluded below.
This warranty extends to the original user/purchaser and only when used, operated and maintained in accordance with Pacific
Operating and Maintenance instructions.
This warranty does not apply to the following wear parts and accessories of the machine including:
Nor does it apply to damage or failure caused by improper use, abuse or neglect. Warranty credit or replacement of return parts
including motors, etc., is subject to incoming inspection of those items.
To secure repair under this warranty, the following procedure should be taken:
• The inoperative machine or warranted parts must be delivered to the authorized dealer with shipping and delivery charges
prepaid. If unable to locate the Dealer, you may contact Pacific at the address listed herein for the location of the nearest
Pacific repair center or agent or for other instructions pertaining to your warranty difficulty.
• Upon compliance with the above warranty procedure, all warranted repairs would be completed at no additional charge or
cost to the user.
• Only Pacific or its authorized dealers and agents may make no charge warranty repairs on this product. All others do so at
their own risk.
This warranty limits Pacific liability to the repair of the product and/or warranted parts replacement and does not include inci-
dental or consequential damages arising from the use of a Pacific machine whether defective or not.
This warranty is in lieu of all other expressed or implied warranties and is extended to the original purchaser/user.
500040
2259 Sheridan
Muskegon, Michigan 49442
Ph: [phone] Fax: [phone]
www.nextwaveofclean.com
13” Model
502422
509710
503711
501220
501202
Description
Cord Assembly
Wheel
Handle Grip, Grey
Bumper, Base
Bumper, Drip Cover
17” Model
502422
509780
503711
501242
501287
20” Model
502422
509781
503711
501260
501287