Panasonic AK-HC3500P User manual

Before operating this product, please read the instructions carefully and save this manual for future use.
Operating Instructions
Multi-Format Camera
Model No. AK-HC3500P
VQTB0273-1

2
For your safety
CAUTION:
This product uses a semiconductor laser system
and is a laser class 1 product complies with
Radiation Performance Standards, 21CFR
SUBCHAPTER J.
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
Don’t make any modifications.
Don’t repair by yourself.
Refer servicing to qualified personnel.
CAUTION:
Invisible Laser radiation is emitted from the
Optical fiber connector when this product is
turned on.
Don’t look into directly into the Optical fiber
connector of this product.
indicates safety information.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE, USE
THE RECOMMENDED ACCESSORIES ONLY.
WARNING:
• TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
• TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, KEEP THIS EQUIPMENT AWAY FROM
ALL LIQUIDS. USE AND STORE ONLY IN
LOCATIONS WHICH ARE NOT EXPOSED TO THE
RISK OF DRIPPING OR SPLASHING LIQUIDS,
AND DO NOT PLACE ANY LIQUID CONTAINERS
ON TOP OF THE EQUIPMENT.
FCC Note:
This equipment has been tested and found to comply
with the limits for a class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the
instruction manual, may cause harmful interference
to radio communications. Operation of this equipment
in a residential area is likely to cause harmful
interference in which case the user will be required to
correct the interference at his own expense.
Warning:
To assure continued FCC emission limit compliance,
the user must use only shielded interface cables when
connecting to external units. Also, any unauthorized
changes or modifications to this equipment could void
the user’s authority to operate it.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (service) instructions in the
literature accompanying the appliance.
This class A digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe A est
conforme à la norme NMB-003 du Canada.
For CANADA
This product contains a CR Coin Cell Lithium Battery
which contains Perchlorate Material — special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.

3
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding-
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord form being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the
cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the
applicable safety instructions listed below. Keep these operating instructions handy for future reference.
IMPORTANT SAFETY INSTRUCTIONS
For your safety
Contents
For your safety .......................................................... 2
Overview ................................................................... 4
Accessories .............................................................. 4
Features ................................................................... 4
Precautions for use ................................................... 5
Controls and their functions ...................................... 6
Mounting the lens ................................................... 12
Adjusting the lens flange back ................................ 13
Performing the viewfinder adjustments ................... 14
Connecting a microphone ....................................... 16
Mounting the camera on a tripod ............................ 17
Component system configuration ........................... 18
System connections 1 (with Multi-Format Camera) ... 20
System connections 2 (with Buildup Unit) ................. 21
System connections 3 (with MSU) ............................ 22
Status displays on viewfinder screen ...................... 23
Checking and setting the calendar ......................... 24
Camera warning displays ....................................... 24
Menu operations ..................................................... 25
Setting menu configuration ..................................... 27
Table of adjustment setting ranges ......................... 32
SD memory card operations ................................... 39
AK-HC3500 connector pin assignment .................. 40
External dimension drawings .................................. 41
Specifications ......................................................... 42

4
Overview
This unit is a new-generation multi-format HD camera that
supports the 1080i format.
It uses a new-generation 2/3-inch 2.2-megapixel IT-CCD
[1920 (H) 1080 (V)] imaging device. This newly developed
CCD employs leading-edge processes and embodies a
fresh look taken at the on-chip lens and CCD structure
to improve the sensitivity, smear and dynamic range by
a significant margin over previous CCDs. Furthermore,
Panasonic’s horizontal single-line readout CCD and
high-precision signal processing combine to achieve pixel
shifting and a dramatic reduction in moire within the band.
Another salient feature is the newly developed digital signal
processor LSI chip which is mounted in the camera head
and supports 14-bit A/D conversion: This chip processes
the gamma, knee, detail, matrix and other process signals,
delivers the kind of multi-functionality, high quality and
high stability that digital technology alone can provide, and
improves the operating ease.
The 14-bit A/D converter is instrumental in creating a
stable wide dynamic circuit with a high signal-to-noise ratio
from the dark area all the way to the highlights. Using the
dynamic range stretch (DRS) function which adjusts the
gamma correction optimally in real time, both the dark areas
and light areas can now be reproduced with startling clarity.
The camera head with its new design features an overall
smaller size and lower profile that neatly taken into
consideration the performance of buildup operations, and
the fact that it is now possible to connect it with the buildup
unit without the need to hook up any cables has resulted in a
significant improvement in both operability and applicability.
The amount of heat generated by the camera has also been
slashed as a result of adopting a low-power-consumption
design for the new circuits and a heat-dissipation design for
the new chassis.
When this Multi-Format Camera is connected to a CCU
(AK-HCU931, optional accessory), not only can HD signals
be input and output but SD signals (D1, VBS) can be output
and RET/PROMPT signals can be input as well.
The iris, pedestal, gain and other camera adjustments can
be carried out by remote control using a unit such as the
ROP (AK-HRP931) or MSU (AK-MSU935) available as
optional accessories.
Accessories
Operating Instructions ........................................................ 1
Camera No. plate (1 to 12) ........................................... 1 set
Camera hangers* ............................................................... 2
Screws* (M3 8 mm) ........................................................ 4
Mount cap ........................................................................... 1
* These accessory parts are used when mounting the buildup
unit (AK-HBU3500). Keep them in a safe place to ensure that
you will not lose or misplace them.
Features
Newly developed 1080I, 2.2 million-pixel CCDs
incorporated
Standard sensitivity of F10 and high sensitivity on a par
with SD.
Smear has been cut to approx. 130 dB and the number
of white marks has been drastically reduced by process
improvements.
H-CCD drive is accomplished at a frequency of 74 MHz to
attain a high response and high resolution.
Digital signal processing LSI with high picture quality
featured in the camera unit
After the process circuits, the signals undergo 14-bit,
74 MHz high-picture-quality digital processing, yielding a
high reliability, more functions and enhanced operating
ease as a result.
Multi-functional enhancer
In addition to the many functions such as skin DTL, there
is a choice of 30 boost frequencies.
Designed to achieve low noise levels of below NC15
Power consumption can be reduced since the fan mode
can be switched according to the situation in which
the camera system is being applied. As a result, the
heat-dissipation design has also been optimized.
Fuller complement of control circuits and auto setup
(ASU) function
Users can select the standard mode or simplified mode.
Peripheral components
Ease of operation can be further improved by configuring
a system where the Multi-Format Camera is used in
combination with the remote operation panel (ROP) and
master setup unit (MSU).
Data trunk function
Two RS-422 and two RS-232C circuits are provided as a
standard feature.
They obviate the need for the cables used with virtual
control, pan-tilt head and lens control, etc.

5
Precautions for use
DON’TS
Do not attempt to disassemble the camera or other units.
In order to prevent electric shock, do not remove screws
or covers. There are no user-serviceable parts inside.
Do not abuse the camera. Avoid striking, shaking, etc.
The camera contains sensitive components which could
be damaged by improper handling or storage.
Do not let the lens remain uncapped when the camera is
not use. If the lens is not installed, do not leave the lens
mount hole uncovered.
Do not touch the surface of the lens or prism.
Do not use strong of abrasive detergents when cleaning
the camera body.
Do not aim the camera toward the sun, no matter whether
it is turned on or not.
Taking images of sunlight and other such conditions for
prolonged periods of time may damage the CCD.
Do not operate the camera outdoors during a lightning
storm.
Do not use the camera in an extreme environment where
high temperatures or high humidity exist.
Do not leave the camera turned on when not in use.
Do not unnecessarily turn the camera power on and off
repeatedly.
Do not block the ventilation slots.
Do not cover the port otherwise block ventilation during
operation. Internal heat buildup can cause a fire.
DO’S
Refer any servicing to qualified service personnel.
Handle the camera with care.
Protect the precision made lens by placing the lens cap
over when the camera is not in use. If the lens is not
installed, protect the surface of the prism by placing the
body cap into the lens mount hole.
Use a mild blower or lens cleaning tissue designed for
coated lenses, to clean the surface of the lens or prism in
the event that it should become dirty.
Use a dry cloth to clean the camera if it is dirty. In case
the dirt is hard to remove, use mild detergent and wipe
gently.
Use caution when operating the camera in the vicinity
of spot lights or bright lights, as well as light reflecting
objects and surfaces.
Take immediate action if ever the camera should become
wet. Turn the power off and have the unit checked by an
authorized service facility.
Follow normal safety precaution to avoid personal injury.
Use the camera in an environment where the temperature
is within 14 °F to +113 °F (–10 °C to +45 °C), and the
relative humidity is less than 85 % (no condensation).
Always turn the power off when the camera is not going
to be used. Operate the camera only when there is
adequate ventilation.
Cooling fan
There is internally provided a cooling fan.
Since the cooling fan is a consumable part, replace it
after about 50,000 hours of operation.
(Be sure to ask the dealer for the replacement.)
When using the unit in windy or snowy conditions or at
the beach or at the waterfront, cover it with the rain cover
(optional accessory) or protect it in some other way in
order to prevent it from getting wet and stop water from
seeping inside.
Use the camera in places with minimal moisture and dust.
Avoid using the camera in places with high
concentrations of moisture or dust since these conditions
will tend to cause damage to the internal parts.
In addition, ensure that the connectors which are not in
use are covered with their protective caps.
Peripheral equipment software
The versions of the software used for the peripheral units
(such as the CCU, ROP and MSU) connected to the
AK-HC3500 may need to be updated.
For further details, contact your dealer.

6
Controls and their functions

7
Controls and their functions

8
Controls and their functions
Lens mount (Bayonet type)
This is where the lens is mounted.
Lens clamp lever
The lens is inserted into the lens mount , and this lever
is then turned to clamp the lens in place.
Lens cable, mic cable clamps
These are used to clamp the lens cable and mic cable in
place.
DCamera hangers (supplied)
When the buildup unit (AK-HBU3500) is used, install
these hangers to the camera with supplied screws
(M3 8 mm).
For details, refer to the Operating Instructions for
AK-HBU3500.
ETripod mount
Before securing the Multi-Format Camera to a tripod,
attach the tripod adapter (SHAN-TM700) which is
available as an optional accessory.
FShoulder pad
This is used when the Multi-Format Camera is to be
carried on the shoulder.
It can be adjusted to position it more toward the front or
more toward the back.
GSlide lock release lever
This is held down while it is used to adjust the front/back
position of the shoulder pad F.
Use it to adjust the position of the shoulder pad so that
the camera can be operated more easily while it is being
carried on the shoulder.
HShoulder strap fitting
This enables the shoulder belt to be attached.
IOptical cable clamp
This enables the optical cable to be clamped.
JCamera No. plate holder
This enables the accessory camera No. plate to be
attached.
KOptical fiber connector
(EDW.3K made by LEMO)
This is used to connect with the CCU (camera control
unit) using the optical fiber cable. When it is not in use,
cover it with its protective cap.
Camera power switch [POWER]
This is used to select the camera power input (power
supplied from the CCU or from an external connector)
and turn the power ON and OFF.
Power LED
This lights up green when power is supplied to the
camera.
When the camera’s power switch is set to OFF, this lights
up red if the CCU is connected, and it goes off if the CCU
is not connected (if the power was turned ON by the
CCU).
Power circuit breaker [BREAKER]
This shuts off the power in the event of an overcurrent
while the DC 12 V power supply is used.
To reset the circuit breaker, eliminate what caused it to
trip, and then press the circuit breaker button.
INCOM connectors 1, 2 [INCOM1, INCOM2]
The INCOM or headset plugs are connected here.
INCOM1 MIC ON/OFF switch [MIC1 TALK]
This is the INCOM1 MIC ON/OFF selector switch.
INCOM1 level control [INCOM1 LEVEL]
This is used to adjust the INCOM1 receiving volume level.
INCOM2 MIC ON/OFF switch [MIC2 TALK]
This is the INCOM2 MIC ON/OFF selector switch.
INCOM2 level control [INCOM2 LEVEL]
This is used to adjust the INCOM2 receiving volume level.
9INCOM1 PGM1 level control [INCOM1 PGM1]
This is used to adjust the INCOM1 and PGM1 mixing
level.
INCOM1 PGM2 level control [INCOM1 PGM2]
This is used to adjust the INCOM1 and PGM2 mixing
level.
INCOM2 PGM1 level control [INCOM2 PGM1]
This is used to adjust the INCOM2 and PGM1 mixing
level.
INCOM2 PGM2 level control [INCOM2 PGM2]
This is used to adjust the INCOM2 and PGM2 mixing
level.

9
RET-A selector switch [RET A]
This switch is used to select the return images to be
switched by RET-A.
The return images which have been set on the ROP
menu are allocated to this switch.
RET-B selector switch [RET B]
This switch is used to select the return images to be
switched by RET-B.
The return images which have been set on the ROP
menu are allocated to this switch.
CALL LED
This lights up green when the CALL switch is pressed
from the ROP, MSU or CCU.
CALL switch [CALL]
This lights the CALL LED on the ROP or MSU and
sounds the buzzer (when ON has been selected as the
buzzer setting).
OPT LED
This indicates the camera’s optical signal reception
status. It normally lights up green. When any problem has
occurred, it lights up red.
When a problem has occurred, clean the optical fiber
connector.
If the problem is not cleared up, immediately turn off the
power, and contact your dealer.
Back tally LED selector switch
This is used to set the back tally LED to ON or OFF.
Back tally LED
This lights when the tally signal is supplied.
This lights up red when the R tally signal is supplied,
green when the G tally signal is supplied, and red when
both the R and G tally signals are supplied.
RET switching control connector [RET CONT]
The cable of the RET switching box (optional accessory)
is connected here for controlling the ON/OFF of RET1, 2,
3 and INCOM1, 2 MIC.
External I/O [EXT I/O]
This signal interface connector is designed to support
future interfacing with external devices.
Camera HD-SDI output1 connector (BNC)
[HD-SDI1]
The camera HD-SDI images are output from this
connector.
Camera HD-SDI output2 connector (BNC)
[HD-SDI2]
Camera images, VF images or RET images can be
selected on the camera menu to output HD-SDI signals
from this connector.
Optional video connector (BNC) [AUX]
This is an auxiliary input/output connector.
The HD analog Y input or Prompt2 output (when the CCU
has a Prompt2 input) can be selected.
When a down-converter (optional accessory) has been
installed in the camera, this connector can be used as a
VBS or D1 output connector.
Genlock sync input/PROMPT output connector
[PROMPT/GL]
When the GL/PROMPT selector switch is set to GL,
the reference signal (tri-level SYNC or B.B.) which is
used to genlock the camera is input to this connector;
Genlock sync signals are input to this connector when
the CCU is not connected. When it is set to Prompt, the
Prompt images input from the CCU are output from this
connector.
GL/PROMPT selector switch
This is used to select the genlock input or the input/output
(genlock input and PROMPT output) signals of the
PROMPT output connector.
Remote connector [REMOTE]
The remote operation panel (ROP, optional accessory) is
connected to this connector.
The [SYSTEM], [FUNC] and [SD DTL] menus of the ROP
cannot be controlled.
Neither can the [HEAD POWER], [CHARA], [BAR],
[MONO], [SD DTL OFF] and [MONITOR (R/G/B/SEQ/
ENC)] switches be controlled.
External power supply input connector [DC IN]
The input of the external DC power supply is connected
to this connector. (DC 10.8 V to 17 V)
MIC1 selector switch [LINE/FRONT MIC/MIC]
This is used to switch the input signal to LINE, FRONT
MIC or rear MIC.
Controls and their functions

10
Rear MIC1 connector [MIC1]
An audio component or microphone is connected to this
connector.
The gain setting can be selected on the camera menu.
Rear MIC2 connector [MIC2]
An audio component or microphone is connected to this
connector.
The gain setting can be selected on the camera menu.
DC output connector [DC OUT]
The R or G tally signal is output from this connector
(open collector). A DC 12 V power supply (up to 1.0 A)
can also be supplied.
If the current exceeds the rating, the power is turned off
forcibly.
Earphone jack [EARPHONE]
When an earphone (optional accessory) is connected to
this jack, the INCOM1 receiving signals can be heard.
Data trunk connector [TRUNK]
The trunk data [RS-422 2 or RS-232C 2] of the CCU
is input to and output from this connector.
The camera menu is used to select the setting.
MIC1 power selector switch
This is used to select what kind of power is to be supplied
to MIC1. (The switch is set to phantom 48 V, AB 12 V or
OFF.)
MIC2 power selector switch
This is used to select what kind of power is to be supplied
to MIC2. (The switch is set to phantom 48 V, AB 12 V or
OFF.)
Grip PTT switch [PTT]
This selector switch is used to set the INCOM1 MIC to
ON or OFF.
The camera menu is used to select the setting.
Grip RET switch [RET]
This is used as return image selector switch.
The camera menu is used to select the setting.
Optical filter selector switch [FILTER LOCAL]
When this switch is pressed and the filter local LED 
lights, the optical filter can be adjusted manually.
When it is pressed again, the optical filter can be
controlled by the ROP.
Filter local LED [LOCAL]
While this LED is lighted, the optical filter can be adjusted
manually.
Monitor output selector switch [MONI SEL]
This is used to select the viewfinder image and the HD
SDI2 image (Y, NAM, R, G, B) in the VF OUT status.
ND filter selector knob
This is used to adjust the optical filter manually when
LOCAL has been selected as the filter setting.
1: CAP, 2: Through, 3: 1/4, 4: 1/16, 5: 1/64
Do not turn this knob while the filter local LED is off.
CC filter selector knob
This is used to adjust the optical filter manually when
LOCAL has been selected as the filter setting.
A: 3200K, B: 4300K, C: 6300K, D: Cross, E: DF0
Do not turn this knob while the filter local LED is off.
Gain selector switch [GAIN]
This is used to select the gain for the camera images.
(LOW, MID, HIGH)
It is not effective when the CCU is connected to the
camera.
The gain setting can be selected on the camera menu.
Camera output selector switch [OUTPUT]
This is used to select the video output (CAM, BAR or
TEST).
It is not effective when the CCU is connected to the
camera.
White balance memory selector switch [W.BAL]
This is used to select the white balance memory.
Data can be recorded in A or B.
The factory settings are established when the switch is
set to PRST.
It is not effective when the CCU is connected to the
camera.
 Assignable switch [USER 1, 2, 3]
The ON/OFF function settings established ahead of time
can be allocated to these switches using the camera
menu.
Controls and their functions

11
SD memory card connector [SD CARD]
The SD memory card (optional accessory) is inserted
here.
For the recording items, refer to the “Table of the
adjustment setting ranges”. (See pages 32 to 33.)
SD memory cards whose operation has been
authenticated (recommended)
Cards made by Panasonic with a memory size of 2 GB
or less (SD-HC memory cards are not supported)
SD Logo is a trademark.
Menu switch [MENU]
When this switch is pressed, the camera’s user menu is
output; when it is pressed again, the menu screen display
is cleared.
JOG dial button
Turning the JOG dial while the menu screen is displayed
moves the cursor to the setting items. The menu settings
are established by operating this dial button.
For details on the menu operations, refer to the section
on the menu operations.
Electronic shutter selector switch [SHUTTER]
This is set to ON when the electronic shutter is to be
used. When it is set to the SEL position, the shutter
speed is switched in the preset range.
It is not effective when the CCU is connected to the
camera.
AWB/ABB start switch [AUTO W/B BAL]
This is used for conducting automatic white balance
adjustments (AWB) or automatic black balance
adjustments (ABB).
It is not effective when the CCU is connected to the
camera.
Lens connector [LENS]
The lens cable is connected to this connector.
Front MIC1 connector [MIC1]
A microphone (optional accessory) is connected here.
When using the microphone, set the MIC1 selector
switch to front MIC. (See page 16.)
The power supply for the microphone can be connected
from this connector. What kind power is to be supplied is
set using the MIC1 power selector switch.
VF connector [VF]
The 2˝ viewfinder cable is connected to this connector.
Rear VF connector
This D-sub connector is used for Viewfinder interface.
Back light switch [LIGHT]
This light switch is used to make it easier to read the
characters on the camera’s back panel.
The brightness can be adjusted using the camera menu.
MIC1 Talk LED [TALK]
This LED lights up green when the INCOM1 MIC is
operational.
It blinks when the MIC has been forcibly set to OFF by a
remote control operation.
MIC2 Talk LED [TALK]
This LED lights up green when the INCOM2 MIC is
operational.
It blinks when the MIC has been forcibly set to OFF by a
remote control operation.
MIC2 selector switch [LINE/MIC]
This switch is used to select LINE or MIC for the input
signals.
Buildup unit I/F
This signal interface connector is used to connect the
Buildup unit.
Tally output connector [TALLY OUT]
The R or G tally signal is output from this connector
(open collector). A DC 12 V power supply (up to 1.0 A)
can also be supplied.
If the current exceeds the rating, the power is turned off
forcibly.
Controls and their functions

12
Mounting the lens
1Raise the lens clamp lever, and remove the mount cap.
Mount cap Lens clamp lever
2Align the guide pin on the lens with the groove at the
top center of the lens mount, and mount the lens.
Guide pin
Groove
3Lower the lens clamp lever to clamp the lens in place.
Lens clamp lever
4Insert the cable into the cable clamp and connect it to
the lens connector.
Lens connector
For details on handling the lens, refer to the
instructions that accompany the lens.
Depending on the lens mounted, it may be necessary
to perform the following lens and camera adjustments.
1. Flange back adjustment for the lens
2. Auto iris operation speed adjustment for the lens
3. White shading adjustment for the lens (performed
using the controls on the camera)
Notes

13
Adjusting the lens flange back
Adjust the flange back (distance from the surface where the lens is mounted to the surface where the images are formed) if the
subject fails to be precisely focused at both the telephoto and wide-angle settings when zoom operations are to be performed.
Once adjusted, the flange back does not need to be adjusted again unless the lens is replaced.
Adjustment method
For details on the adjustment method and positions of the lens parts, refer also to the instructions that accompany the lens.
Note
About 9.9 ft. (3 m)
1Mount the lens on the camera. Do not forget to connect
the lens cable at this time.
2Set the lens iris to manual, and open the iris.
3Set the lighting in such a way that the appropriate video
output level is obtained at a distance of about 9.9 ft.
(3 m) from the flange back adjustment chart.
If the video level is too high, use a filter or shutter.
4Loosen the screw that secures the F.f (flange focus)
ring.
Depending on the lens concerned, this ring may be
marked as the “F.b” (flange back) ring.
Note
5Set the zoom ring to the telephoto position either by
manual or electrical means.
6Shoot the flange back adjustment chart, and turn the
distance ring to adjust the focus.
7Set the zoom ring to the wide-angle position, and turn
the F.f ring to adjust the focus. Take care not to move
the distance ring.
8Repeat steps 5 to 7 until the chart is focused properly
at both the telephoto and wide-angle positions.
9Tighten up the screw that secures the F.f ring.

14
Performing the viewfinder adjustments
(The viewfinder is an optional accessory.)
Attaching the viewfinder
1Check that the camera’s POWER switch is at the OFF
position.
2Pull up the knob on the mounting plate and slide the
plate to attach the viewfinder.
Pull up the knob
3Tighten the stopper screw securely.
Stopper screw
4Connect the plug to the VF connector.
When connecting the plug to the VF connector,
ensure that it is fully and securely inserted.
Note
Detaching the viewfinder
1Check that the camera’s POWER switch is at the OFF
position.
2Loosen the stopper screw, pull up the knob on the
mounting plate and slide the viewfinder along and off
the plate.
Stopper screw
Pull up the knob
3Disconnect the plug from the VF connector.

15
Performing the viewfinder adjustments
(The viewfinder is an optional accessory.)
Left or right position adjustment
1Loosen the stopper screw.
Viewfinder
Stopper screw
2Move the viewfinder to the left or right to adjust its
position.
3Tighten the stopper screw.
Stopper screw
Forward or backward position
adjustment
1Rotate the viewfinder forward/backward position fixing
lever towards the outside to release it from the locked
position.
Viewfinder forward/backward
position fixing lever
Viewfinder
2Move the viewfinder forward or backward to adjust its
position.
3Rotate the viewfinder forward/backward position fixing
lever in the opposite direction until it locks.
Viewfinder forward/backward
position fixing lever

16
Connecting a microphone
When the microphone is mounted on
the viewfinder (optional accessory)
for use
A microphone such as the AJ-MC700 microphone kit
(optional accessory) can be mounted on the viewfinder.
1Open the microphone holder.
Microphone
holder
2Mount the microphone and tighten up the clamp screw.
Clamp screw
3Connect the microphone cable to the front MIC1
connector on the camera.
Front MIC1 connector
4If the audio channel whose signals are to be recorded
so requires, set the MIC1 selector switch to FRONT
MIC.
MIC1 selector switch

17
Mounting the camera on a tripod
Use the tripod attachment, available as an optional
accessory, to mount the camera on a tripod.
1Mount the tripod attachment on the tripod.
Select the appropriate holes from among the holes
on the bottom of tripod attachment depending
on where the center of gravity of the camera and
tripod attachment falls. If the holes selected are
not appropriate, the center of gravity will not be
supported, as a result of which the camera may
drop off or fall over, which in turn may possibly
cause injury.
Check that the diameter of the holes selected
for mounting matches the diameter of the screw
holes of the tripod platform. If these diameters do
not correspond, the tripod attachment will not be
secured properly, as a result of which the camera
may drop off or fall over, which in turn may possibly
cause injury.
Note
Tripod platform
Tripod attachment
2Mount the camera on the tripod attachment. Slide the
camera toward the front along the groove until a click is
heard.
Now check that the camera is secured properly.
Detaching the camera from the tripod attachment
While pushing the red lever, move the black lever in the
direction of the arrow, and slide the camera toward the
back.
Red lever
Tripod attachment
Black lever
<Note>
If the pin of the tripod attachment fails to return to its
original position after the camera has been detached,
push the red lever again and simultaneously move the
black lever in the direction of the arrow to return the pin
to its original position.
Bear in mind that the camera cannot be mounted if the
pin still remains at the center.
Concerning the steps for ensuring that the
camera does not slip or drop out of position
When installing the camera on a crane or at some
other position high above the floor or ground, first
check that the crane can bear the weight of the entire
system including the camera, lens and connecting
cables, and then use the specified tools to install the
camera securely.
Be absolutely sure to ensure that the camera will not
drop from its position by looping an anti-drop wire
around its handle and securing the end of the wire at a
point above the camera, as shown in the figure below.
Note
Anti-drop wire

18
Component system configuration
An example of the standard system consisting of the Multi-Format Camera (AK-HC3500) and peripheral components is
described below and shown on the following page. The MSU (AK-MSU935) is not required unless a multiple number of cameras
are to be controlled.
The basic system configuration includes the lens, Multi-Format Camera, viewfinder, camera control unit (CCU) and remote
operation panel (ROP).
System block diagram
Microphone Kit
AJ-MC700
2˝ Electronic HD Viewfinder
AJ-HVF21
Handy lens
Multi-Format Camera
AK-HC3500
Tripod Attachment
SHAN-TM700
SD memory card
Master Setup Unit
AK-MSU935
8˝ LCD Viewfinder
AK-HVF931A
Remote Operation Panel
AK-HRP931
Camera Control Unit
AK-HCU931
ROP cable
Large lens
Buildup Unit
AK-HBU3500

19
Component system configuration
Outline of peripheral components
Camera Control Unit (CCU: AK-HCU931)
This is the Multi-Format Camera’s camera control unit.
It is connected to the Multi-Format Camera using an
optical fiber cable.
HD/SD video input and output can be supported by
inserting the HD/SD output unit.
Remote Operation Panel (ROP: AK-HRP931)
The ROP is connected to the CCU using the ROP cable,
and enables the camera, CCU and lens to be operated by
remote control.
Master Setup Unit (MSU: AK-MSU935)
When a multiple number of cameras and CCUs are used,
the MSU can operate up to 12 units either separately or
simultaneously by remote control.
It can be operated together with the ROP.
2˝ Electronic HD Viewfinder (2˝ VF: AJ-HVF21)
This is the viewfinder for the Multi-Format Camera.
8˝ LCD Viewfinder (8˝ LCD VF: AK-HVF931A)
This is the LCD viewfinder for the Multi-Format Camera.
It can be used at the same time as the 2˝ viewfinder.
It can still be operated when the system is built up.
Buildup Unit (AK-HBU3500)
A large-sized lens can be mounted on the multi-format
camera to enable the same operations as for a
large-sized camera can be undertaken.
Component connections
Refer to pages 20 to 22 for the component connections.
After all the components have been connected (the monitor
system may be connected afterward), set the CCU’s main
power switch to the ON position.
Then turn on the camera’s power switch.

20
System connections 1 (with Multi-Format Camera)
2˝ Electronic HD Viewfinder
AJ-HVF21
Lens
Multi-Format Camera
AK-HC3500
ROP cable
Remote Operation Panel
AK-HRP931
Camera Control Unit
AK-HCU931
Optical cable
Before proceeding with the connections, set the CCU power switch to the OFF position.
Connect the optical cable to the Multi-Format Camera and CCU.
Connect the ROP cable to the CCU and ROP.
When the camera power switch is set to ON after the CCU main power switch has been set to ON, the camera can be
controlled using the ROP.
Upon completion of shooting, set the CCU camera power switch and main power switch to OFF.