Panasonic CT-27G30CT User manual

Color Television
Operating Instructions ®
Read these instructions completely before operating this set.
Contents subject to change without notice or obligation. Printed in U.S.A.
TQB2A09431

Safety Instructions
WARNING
WARNING: To reduce the risk of electric shock do not remove cover or back. No
user-serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with ar-
_ row-head within a triangle _
is intended to tell the user
that parts inside the product
are a risk of electric shockto
persons.
The exclamation point within
a triangle is intended to tell
the user that important oper-
ating and servicing instruc-
tions are in the papers with
the appliance.
Note To CATV System Installer: This reminder is provided to call the CATV system installer's attention to Article
820-40 ofthe NEC thatprovidesguidelinesfor proper grounding and, in particular,specifies that the cable ground shall be
connected to the groundingsystem of the building, as close to the point of cable entry as practical.
Safety Instructions For Television Receivers
1. Read and apply the operating instructionsprovided with your television receiver.
2. Read all ofthe instructionsgiven here and retain them for later use.
3. Unplug this television receiverfrom the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
4. Do not use attachments not recommended by the television receiver manufacturer as they may cause hazards.
5. Do not use thistelevision receiver near water. For example: Avoid placing itnear a bathtub,washbowl, kitchen sink,or
laundry tub, in a wet basement, or near aswimming pool, etc.
6. Do not place thistelevisionreceiver on an unstable cart, stand, or table. The television receivermay fall, causing serious
injuryto a child or adult, and serious damage to the appliance. Use only with a cart or stand recommended by the
manufacturer, or soldwiththe television receiver. Wall or shelf mounting should follow the manufacturer's instructions,
and should use a mounting kit approved by the manufacturer.
6A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart combination to overturn.
7. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to insure
reliable operation of the television receiver and to protect it from overheating. These openings must not be blocked or
covered. The openings should never be blocked by placing the television receiver on a bed, sofa, rug or other similar
surface: This television receiver should never be placed near or over a radiator or heat register. This television receiver
should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.
8. Operate only from the type of power source indicated on the marking label. If you are not sure of the type of power
supplied to your home consult your television dealer or local power company. For television receivers designed to
operate from battery power, refer to the operating instructions.
9. This television receiver isequipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug
fully intothe outlet, try reversing the plug. If
the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do EXAMPLEOF ANTENNAGROUNDINGAS ANTENNA LEAD-IN
not defeat the safety purpose of the polarized PER(NEC)NATIONALELECTRICALCODE WIRE
plug.
10. Do not allow anything to rest on the power
cord. Do not locate this television receiver
where the cord will be abused by persons
walking on it.
11. Follow all warnings and instructions marked
on the television receiver.
12. Do not overload wall outlets and extension
cords as this can result in fire or electric
shock.
13. Never push objects of any kind into this
television receiver through cabinet slots as
they may touch dangerous voltage points or
short out parts that could result in a fire or
electric shock. Never spill liquid ofany kind on
the television receiver.
ANTENNA
(NEC SECTION 810-20)
3ROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
-2-

14.Ifanoutsideantennaisconnectedtothetelevisionequipment,besuretheantennasystemisgroundedsoastoprovide
someprotectionagainstvoltagesurgesandbuiltupstaticcharges.IntheU.S.Section810oftheNationalElectrical
CodeandinCanadaPart1oftheCanadianElectricalCodeprovidesinformationwithrespecttopropergroundingofthe
mastandsupportingstructure,groundingofthelead-inwiretoanantennadischargeunit,sizeofgroundingconductors,
locationofantenna-dischargeunit,connectiontogroundingelectrodes,andrequirementsforthegroundingelectrode.
SeeFigure.
15.Foraddedprotectionforthistelevisionreceiverduringalightningstorm,orwhenitisleftunattendedandunusedforlong
periodsoftime,unplugitfromthewalloutletanddisconnecttheantenna.Thiswillpreventdamagetothereceiverdueto
lightningandpower-linesurges.
16.Anoutsideantennasystemshouldnotbelocatedinthevicinityofoverheadpowerlinesorotherelectriclightorpower
circuits,orwhereitcanfallintosuchpowerlinesorcircuits.Wheninstallinganoutsideantennasystemextremecare
shouldbetakentokeepfromtouchingsuchpowerlinesorcircuitsascontactwiththemmightbefatal.
17.Unplugthistelevisionreceiverfromthewalloutlet,andreferservicingtoqualifiedservicepersonnelunderthefollowing
conditions:
a. Whenthepowercordorplugisdamagedorfrayed.
b. Ifliquidhasbeenspilledintothetelevisionreceiver.
c. Ifthetelevisionreceiverhasbeenexposedtorainorwater.
d. Ifthetelevisionreceiverdoesnotoperatenormallybyfollowingtheoperatinginstructions.Adjustonlythosecontrols
thatarecoveredbytheoperatinginstructionsasimproperadjustmentofothercontrolsmayresultindamageandwill
oftenrequireextensiveworkbyaqualifiedtechniciantorestorethetelevisionreceivertonormaloperation.
e. Ifthetelevisionreceiverhasbeendroppedorthecabinethasbeendamaged.
f. Whenthetelevisionreceiverexhibitsadistinctchangeinperformance- thisindicatesaneedforservice.
18.Donotattempttoservicethistelevisionreceiveryourselfasopeningorremovingcoversmayexposeyoutodangerous
voltageorotherhazards.Referallservicingtoqualifiedservicepersonnel.
19.Whenreplacementpartsarerequired,besuretheservicetechnicianhasusedreplacementpartsspecifiedbythe
manufacturerthathavethesamecharacteristicsastheoriginalpart.Unauthorizedsubstitutionsmayresultinfire,
electricshock,orotherhazards.
20.Uponcompletionofanyserviceorrepairstothistelevisionreceiver,asktheservicetechniciantoperformroutinesafety
checkstodeterminethatthetelevisionisinsafeoperatingcondition.
21.WARNING: To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
22. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN RECEPTACLE OR
OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NOTE: This equipment is designed to operate in the U.S.A., Canada and other countries where the broadcasting system and
AC house current is exactly the same as.in the U.S.A. and Canada.
Important Information Regarding Use of Video Games, Computers, Teletext or Other Fixed Image Displays.
The extended use of fixed image program material can cause a permanent "shadow image" on the picture tube. This
background image is viewable on normal programs in the form of a stationary fixed image. This type of irreversible picture
tube deterioration can be limited by observing the following steps:
A. Reduce the brightness/contrast setting to a minimum viewing level.
B. Do not display the fixed image for extended periods of time.
C. Turn the power off when not in actual use.
NOTE: The marking or retained image on the picture tube resulting from fixed image use is not an operating defect and as
such is notcovered byWarranty. This product is not desig nedto display fixed image patterns for extended periods of
time.
Power Source:
Channel Capability:
Video Input Jacks (2):
Audio Input Jacks (2):
To Audio AMP Jacks:
S-VHS Input Jack:
Stereo Sound
Surround Sound
Closed Caption Display
Picture in Picture:
Specifications
120V 60Hz, AC
181 channels (See chart)
VHF 2-13, UHF 14-69, Cable 125 channels
1V p-p, 75 ohm, phon0 jack type
High impedance- 10K ohm, 500mV rms
0-4.0V rms 10K ohm
S-Video (Y-C) Connector
Two Tuner
Specifications are subject to change without notice or obligation.
-3-
Channel Capability Chart
BAND USA/CAN
VHF 12
UHF 56
CABLE (Mid-Band) 15
CABLE (Super Band) 14
CABLE (Hyper Band) 28
CABLE (Ultra Band) 56
TOTAL CHANNELS! 181

Introduction
Congratulations on Your New Purchase
Your new video component features an all solid state chassis which is designed to give you many years of enjoyment. It
was thoroughly tested and adjusted at the factory for best performance.
In order for you to take full advantage of your new video component, please read and follow the installation and operating
instructions supplied with this product.
Customer's Record
The model and serialnumber of this productmay befound on itsbackcover, You should notethe modeland serial number
in the space provided and retain this book as a permanent record ofyour purchase to aid in identificationin the event of
theft or loss.
Model Number: Serial Number:
Table of Contents
Safety Instructions ............................. 2
Specifications ................................. 3
Introduction ................................... 4
Installation ......... . ........... ............... 5
Receiver Location .............................. 5
Optional Extemal Equipment Connections ....... :5
AC Power Supply Cord ......................... ' 5
Battery Installation ............................. 5
Antenna/Cable Connections ..................... 6
Picture in Picture External Video & Ant Connection. 7
Location of Controls (Remote) .................. 8
Location of Controls (Receiver) ................. 9
Quick Reference Control OPeration .............. 9
Control Operation ............................. 10
Power Button ................................. 10
Volume (Vol) Buttons .......................... 10
Mute Button .................................. 10
Channel Change Features ..................... 10
Channel (Ch) Buttons ....................... 10
Keyboard "0 through 9" Buttons .............. 10
VCR Function Buttons ......................... 10
TVNideo Button .............................. 11
Recall Button. ................................ 11
R-Tune (Rapid Tune) Button ................... 11
Multi Button .................................. 11
Cable (TV) Power Button ...................... 12
PIP (Picture in Picture) Button .................... 12
PIP Channel Buttons .......................... 12
PIP Swap Button ............................. 12
PIP Size Button ............................... 13
PIP Freeze Button ............................ 13
PIP Move Button ........ ............ •........... 13
PIP Search Button ........ '...... .............. 13
Main Menu (Icons) ............................ 14
Picture Adjustments ........................... 15
Color ....................................... 15
Tint ....................................... 15
Brightness ................................. 15
Picture .................................... 15
Sharpness ................................. 15
Picture Norm ............................... 15
Game Guard .... ......................... .... 16
Game Guard (Lockout) ...................... 16
Game Guard (Unlock) ....................... 17
Timer Features ............ :.................. 18
Sleep Timer ................................. 18
Program Timer ............................. 19
Set-Up Features ............................. 20
Menu ... .................................. 20
CC (Closed Caption) On Mute ................. 21
Set Time (Clock) ........................... . 22
Antenna Tuning Mode ....................... 23
Auto Programming .......................... 24
Manual Programming ........................ 25
CC (Closed Caption) Mode ........ :. ........ 26
Channel Caption (Station Identifier) ............. 27
Audio Adjustments ............................ 28
Bass, Treble & Balance Adjustments .......... 28
Audio Norm ................................ 28
Audio Mode Selection (Stereo/SAP/Mono) .... 29
[TV] Speaker ................................. 29
Surround Sound ............................ 30
AI Sound .................................. 30
Input Select .................................. 31
Main (Picture) Input Selection ...... ........... 31
PIP Input Selection .......... "............... 31
Programming The Universal Remote Control .... 32
VCR, LDP & Cable Converter Box
Infra-Red Codes .......................... 33
Optional Equipment Connection & Operation ... 34
Stereo Connection (To Audio AMP) ............. 34
Video/Audio Connection ....................... 34
S-Video Connection .......................... 35
Care & Cleaning ............................... 35
Power Loss ................................... 35
Troubleshooting Chart ........................ 36
-4-

Installation
Receiver Location
Locate for comfortable viewing. Avoid placing where sunlight or other bright light (including reflections) will fall on the
screen.
Use of some types of fluorescent lighting can reduce remote control transmitter range.
Adequate ventilation is essential to prevent internal component failure. Keep away from areas of excessive heat or
moisture.
To insure optimum color purity do not position magnetic equipment (motors, fan, other speakers, etc.) nearby.
Optional External Equipment Connections
The Video/Audio connections between components can be made with shielded video and audio cables. For best perfor-
mance, video cables should utilize 75 ohm coaxial shielded wire. Cables are available from your dealer or electronic
supply house.
Before you purchase any cables, be sure you know what type of output and input connectors your various components
require. Also determine the length of cable you'll need.
AC Power Supply Cord
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT OF AC OUTLET AND FULLY INSERT. DO NOT USE THIS (POLARIZED) PLUG
WITH A RECEPTACLE OR OTHER OUTLET UNLESS THE BLADE CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE. Polarized Plug
Remote Control Battery Installation & Replacement
Battery Installation
Batteries: Use two "AA" batteries.
1. Turn the Transmitter face down. To remove bottom cover, press down
on marking and slide cover off in the direction indicated.
2..Install the batteries as shown in the battery compartment. (Polarity (+)
or (-) must be correct.)
3. Replace the cover and slide in reverse until the lock snaps.
.Precaution on Battery Use
Incorrect installation can cause battery leakage and corrosion that will
damage the Remote Control Transmitter.
Observe the Following Precautions:
1. Batteries must be replaced as a pair.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (Example: "Zinc Carbon" with "Alkaline").
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used
batteries.
5. Battery replacement is necessary when Remote Control reacts
sporadically or stops operating the Receiver.
II IIII
_ "=F=P-
®
J,.J
4-J
0_
®
®
®
,=_d=. ,.._..
_C Press Down Here And
over Back
"":!ii""
\J
-5-

Antenna/Cable Connections
Antenna Connection - For proper reception of VHF/UHF channels an external
antenna is required. For best reception an outdoor antenna is recommended.
Antenna Mode must be set to TV. (Refer to Antenna Mode section.)
Incoming Cable From Home Antenna (75 Ohm)
VHF/UHF
on Back of Set
Indoor Outdoor
Typical VHF/UHF Antenna
Incoming Cable From Home Antenna (300 Ohm)
VHF/UHF
on Back of Set
300 to 75 ohm Matching
Transformer (Not Included)
Cable Connection - For reception of cable channels (01-125) connect the cable supplied by your local Cable company.
Antenna Mode must be set to CABLE. (Refer to Antenna Mode section.)
Incoming 75 Ohm Cable (From Cable Company)
VHF/UHF
on Back of Set
NOTE: Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A
Cable Converter box is required for proper reception. Check with your local Cable company for its compatibility
requirements.
Other Video Equipment
VCRs, Video Disc Players, Computers, TV games and Teletext equipment can also be connected to the antenna input
connection.
-6-

Picture in Picture (Two Tuner) Antenna and External Video Connection
This Receiver hasthe"PICTURE IN PICTURE" featu rethat usestwotuners. This allows youtowatch 2 live broadcastsat
thesame timewithoutan externalvideosource. (See Antenna Connection, Detail 1.) Ifyou wishan external videosource
(VCR, Laser Disc Player or Camcorder) may be monitored in the PIP Frame. (See External Video Connection, Detail2.)
Detail I - PIP Antenna Connection
TERMINALS ON BACK OF RECEIVER
Incoming Cable
From Antenna Or
Cable TV System
To ANT Terminal
®
ANT
-@ S-VIDEO
_VIDEO
__® ® ® ,_
AUDIO
®®®.,
2_ 1-- INPUT
OAUDIO
AMP
®
ANT
Detail 2- PIP External Video Connection
]ERMINALS ON BACK OF RECEIVER
•@S-VIDEO
®®
AUDIO
.® ® ®.,
2 1 INPUT
O AUDIO
AMP
To ANT Terminal
VCR or VIDEO
DISC PLAYER
I_--',_)
TERMINALS ON BACK OF VCR
OUT
VIDEO OUT
AUDIO OUT
ANT INPUT
To VCR b,...=
Ant Input
Helpful Hints:
The PIP will operate using Audio/Video input terminals 1 or 2.
Use the TVNIDEO button (when the PIP frame is displayed)
to select proper mode.
The PIP feature will operate using S-Video input terminal 1.
_A
_51gna.I_Splittel _
(not Included)'---I_'_.._ [
Incoming Cable
From Antenna Or
Cable TV System

Location of Controls (Remote Control)
®POWER
OMULTI
CD ®
®
®
®
@
®
@
®
ACTION
(__-T_UNE TVNIDEO
GD
® ® ®
® ® ®
®®®
I- VCR CABLE
i POWER RECOR_ POWER
ii--- I r---hii--- I
ITV/VCR STOP PAUSE i
tr---I IZ_ IZZ_
i_REEZESEA.C."_.WAPI
VCR LDP l VCR CHANNEL_.,
I
®
®
@
@
@
@
@
@
@
J

Location of Controls (Receiver)
Front Control Panel
POWER 41VOLUME Ib • CHANNELA ACTION "I-V/VIDEO
Remote Control
Sensor
Quick Reference Control Operation (Remote & Receiver)
QPower Button - Press to turn ON or OFF. (pg.10)
Q Volume Buttons- Press to adjust Sound Level. Press to adjust Audio Menus, Video Menus and select operating
features when menus are displayed. (pg.10)
QChannel Buttons - Press to select programmed channels. Press to highlight desired features when menus are
displayed. Also used to select Cable Converter box channels after programming Remote Control Infra-red codes
(the TV/AUX/CABLE switch must be set in CABLE position). (pg.10)
Q/Video Button - Press to select TV or one of two Video Inputs, for the Main Picture or the PIP frame (when PIP
frame is displayed). (pg. 11)
QAction Button - Press to display Main Menu and access or exit On Screen feature and Adjustment Menus. (pg. 14)
QMulti Button - Programmable to operate up to six Remote Function buttons. (pg.11)
QMute Button - Press to mute sound. A second press returns sound. (pg.10)
QR-Tune (Rapid Tune) Button - Press to switch between two channels. (pg.11)
QRecall Button - Press to display Time, status of Sleep Timer, Channel, Video Mode, Channel Caption (Station
Identifier) and Audio Mode. (pg.11)
QKeyboard "0 through 9" Buttons - Press desired channel number to access any channel. (pg.10)
OVCR Function Buttons - Programmable to operate many brands of VCRs. (pg.10)
QCable Power Button- Programmable to operate selected CATV converter boxes, (pg.12)
QPIP (Picture In Picture) Button - Press to display the PIP frame, press again to remove PIP frame. (pg.12)
QSwap Button - Press to interchange PIP frame with Main Picture (when the PIP frame is displayed). (pg.12)
OSize Button - Press to select size of PIP frame (when the PIP frame is displayed). (pg.13)
OMove Button - PresstopositionPIP frame toany cornerofthe Main Picture(when PIP frame isdisplayed). (pg.13)
QFreeze Button - Press tostop action in the Main Picture or PIP frame (when the PIP frame isdisplayed). (pg.13)
QSearch Button - Press the SEARCH buttonto automaticallyscan channels which are programmed intomemory.
Press the SEARCH button again to delete Search frame. (pg.13)
GPIP Channel Buttons- When the PIP frame isdisplayed, press the PIP Channel (CH) UP button to select the next
higher programmed channel inthe PIP frame. Pressthe Channel (CH) DOWN button to selectthe next lower pro-
grammed channel in the PIP frame. (pg.t 2)
QVIAUX/CABLE Switch -This switch is used toselectthe proper mode when programming Remote Control Infra
red codes or operating the TV or external equipment (VCR, LDP or Cable TV Converter box).
QCR/LDP Switch -This switch is used to select the proper mode when the TV/AUX/CABLE switch isin the AUX
position to program the Remote Control Infra red codes or operate the auxiliary equipment (VCR, LDP).
--9--

Control Operation
Power Button - Pressthe POWER button to turn
ON. Press again to turn OFF.
POWER
Volume Button -Press the VOLUME (VOL)
LEFT or RIGHT button for desired listening level (when
On Screen Menus are not displayed).
Decreases
Volume Level
Increases
Jme Level
Located On Remote Control
Channel Change - (Twooptions)
Option 1.
Press the CHANNEL (CH) UP or DOWN button to
sequentially scan through programmed channels
(when On Screen Menus are not displayed).
NOTE: TV/AUX/CABLE switch (located on Remote)
must be set in TV position. TV/AUX/CABLE
Located On Remote Control
SelectsNe
LowerChannel
Selects Next
Higher Channel
Option 2.
Press two digits on keyboard (Example press 0,
then 5 for channel 05). For channels over 99, press
three digits on keyboard.
Mute Button -Press the MUTE button toquickly
reduce sound level (Mute will appear on screen). Press
again to restore sound.
MUTE
Helpful Hints:
• Helpful information will display On Screen momen-
tarily when Receiver is first turned on and when the
channel is changed.
• When using keyboard entry for channels 10,11 and
12 in the CABLE mode there is a slight delay before
channel change because of the capability of tuning
cable channels 100 to 125.
• If you do not receive channels above 13, confirm the
type of signal at ANT Input (TV or Cable) and set the
TV or Cable Tuning Mode accordingly. (Refer to Set
Up Feature, Antenna selection.)
NOTE: If "SPEAKER OFF" is displayed On Screen
after pressing the VOLUME button, refer to
Audio Menu to turn Speakers "ON".
]
I® ® ®1
I1® ®1I
I® ® ®1
I_c ik
VCR Function Buttons - TheVCRFUNC-
TIONbuttons have been designedtooperate numerous
brands of VCRs. The infra-red code must be obtained
priorto use. (Please refer to Programmingthe Universal
Remote for programming instructions.)
NOTE: The TV/AUX/CABLE switch (located on Re-
mote)must be inthe AUX position(Center). The
VCR-LDP switch must be in the VCR position.
TVlAUX/CABLE
VCR I
POWER RECORD I
F-1 r"-n _
REW PLAY FF
MOVE SIZE PIP
TVNCR STOP PAUSE
r-1Fi-7 r-7
FREEZE SWAP
vCR/LDP VCR CHANNEL
-10-

l'V/Video Button - Press the TVNIDEO button
to select desired input for Main Picture or PIP frame
(when PIP frame is displayed).
TVNIDEO
Signal connected to: Main Picture
REAR VIDEO/AUDIO INPUT 2 JACKS /
REAR VIDEO/AUDIO _
INPUT 1 JACKS
TV or CABLE
VIDEO 2 I
v,o o,II
CH 02 f_ J
Signal connected to:
-I ' V'OEO'II_
TV or CABLE _ PIP CH 02 I.._.l_J
L__ PIP Frame
Recall Button - Press the RECALL button to
review:
•Audio Mode status
• CH number or Video Input selected
•Sleep Timer status
•Clock time
•Channel Caption (Station Identifier)
RECALL SAP CH O3
MONO XYYZ
29 1:00
R-Tune (Rapid Tune) Button - Pressthe
R-TUNE (RAPID TUNE) button to instantly switch
between the last two channels selected (without any On
Screen display being activated).
R-TUNE
CHANNEL NOW _CHANNEL TUNED
BEING VIEWED IMMEDIATELY BEFORE
Press Button
Press Button Again
-11 -
Multi Button --The MULTI button can be
programmed to operate up to 6 Remote function
buttons at the same time. For Example: TV
Power/On, VCR Power/On (selected brands) can be
operated at the same timewith one press of the MULTi
button.
Procedure
I. Firstprogram the Remote forthe selectedVCR
Infra-redaccess code.Confirmthatthe Remote
Controliscompatiblewiththeequipment.
2. Face theRemote Controltransmitteraway fromall
equipment remote sensors.
3. Press and hold Remote "IV Power button,then
press and holdthe MULTI buttondown simulta-
neously.(Allpreviouscommands are erased.)
(TV) POWER MULTI
PRESS SIMULTANEOUSLY
4. Press amaximum of 6Function buttons on the
Remote.
Each buttonyou pressisequalto one function. Ifsix
Remote buttonfunctionsare entered, all willregister
in the MULTI button memory in the sequence
entered. When less than six Remote button
functions are entered, press the MULTI button to
end the program mode. (Waiting more than 30
seconds without pressing another button will also
end the program mode.)
The following is an example of Remote functions
that can be programmed into the MULTI button.
- TV Power- For turning"iV ON and OFF.
- VCR Power - For turning VCR ON and OFF
(selected brands after programming it's infra-red
access code, if necessary).
Bothcan be turned ON orOFF withone press ofthe
MULTI button.
NOTE: To activate VCR Power orCable box Power
or other VCR/Cable box functions, the
TVNCR/CABLE switch mustbe put intothe proper
mode during Multi buttonprogram.
(l'V) POWER VCR POWER MULTI
To delete entered functions - Press the Remote
TV POWER and MULTI buttons simultaneously.
Now you can enter from one to sixdifferent Remote
functions. (TV)POWER MULTI
PRESS SIMULTANEOUSLY
NOTE:
You can also program the MULTI button to perform
most individual Remote Control button functions.
Buttons which continuously perform a function as
long as pressed (Volume Up/Down, Channel
Up/Down, etc.) cannot be programmed. Only those
buttons which perform a function when initially
pressed (Power On/Off, Mute, Direct Channel Entry,
etc.) can be programmed.

Cable Power Button -The CABLE Power
button on the Remote Control has been designed to
operate selected brands ofCable Converter Boxes. The
proper Cable Converter Box infra-red code must be
obtained priorto use. (Please refer to Programming the
Universal Remote for programming instructions.) The
TV/AUX/CABLE switch should be in the cable position.
NOTE: Use the Channel UP and DOWN buttonson the
Remote for selecting Cable Converter Box
Channels.
Located On Remote Control
CABLE
POWER
Use to select Cable Box
Channels after programming
Infra-red Code.
PIP (Picture in Picture) Button -This
feature allows the viewer to monitor one channel
program while watching another. The monitored source
(PIP) can be a different channel or a different video
source (such as a VCR) when connected to the input
jacks.
• The TV/AUX/CABLE Switch should be in the TV
position (LEFT) before operating PIP buttons.
• S-Video connection will also operate the PIP feature
(refer to OPTIONAL S-VIDEO VHS CONNECTION
section).
• When the Main Picture is in Video mode with no
signal, the PIP will not operate properly.
PIP Operation
1. Press the PIP button. The PIP frame will appear at
the position itwas last displayed. The Main Picture
channel and PIP channel will display momentarily.
Audio will be that of Main Picture.
2. To select CHs for the Main Picture, use the Remote
Control Keyboard or Channel UP/DOWN buttons.
To select CHs for the PIP frame use the Remote
Control PIP Channel UP/DOWN buttons.
3. Press the PIP button again to cancel PICTURE IN
PICTURE feature.
NOTE: For PIP Video source connection, refer to PIP
Antenna and External Video connection section.
PIP Channel Buttons - Pressthe(PIP)CH
(CHANNEL) UP or DOWN buttonwhile the PIP frame is
displayed tosequentially scan through Channels.
Scan Channel DOWN Scan Channel Up
(next lower) (next higher)
PIP Swap Button -Press the SWAP button
(when the PIPframe isdisplayed)to interchange what is
being viewed on the Main Picture with that of the PIP
frame.
CH O2
PIP VIDEO 1
Audio will be that of the Main Picture.
Main
Picture
with
Sound
CH 2
PIP CH 5
r-1
Main Picture
Channel
11----
Picture in
Picture
Channel
Picture in
Picture
Frame
-12-

PiP Size Button - Press the SIZE button (when
the PIP frame is displayed) to choose either the large or
small PIP frame.
/
Large PIP Frame Small PIP Frame
PIP Freeze Button - Press the FREEZE button
to stop action in the Main Picture or PIP frame.
PIP Move Button - The PIP frame may be
located at any comer ofthe Main Pictureby pressingthe
PIP MOVE button (when the PIP frame is displayed).
NOTE: Each time MOVE button is pressed (when the
PIP frame isdisplayed), the PIP frame will move
(counterclockwise) as illustrated.
l-q- !--1
-[B
Main
Picture
_reezeFrame
NOTE:
• Pressing the FREEZE button when the PIP frame is
not displayed willstop action in the Main Picture and
display it on the PIP frame.
• Pressing the FREEZE button when PIP frame is
displayed will stop action in the PIP frame, press the
FREEZE button again to continue action.
• Press the PIP button to delete PIP frame.
PIP Search Button -The SEARCHbuttonal-
lowsyou to scan channels in "Channel Scan memory"
one at a time. This feature will work with or without an ex-
ternal video signal as the Main Picture.
PIP CH 2
E_ Press Search
to Scan
Search Operation
1. Press the SEARCH button. A PIP frame willappear
on the Main Picture.(The PIP frame willcontinuous-
ly scan channels insequence as programmed into
channel memory.)
2. Two Options:
Option 1.
Press the SEARCH buttonagain, the Search frame
will disappear.
Option 2.
Press the PIP buttonto stop Search feature on de-
sired picture for PIP frame. (Press the SWAP button
to interchange whatisbeing viewed onthe Main Pic-
ture with that of the PIP frame.
-13-

Main Menu (Icons)
'-'I I EXITI I INPUTI[_
['_--I IP'CTUREI I AUD'Oir-_
I_AM_I ICHANNELIIGUARDI [CAPTIONI _
I'_ I TIMER I ISET_UPI _--_
ACTION
Displays and Exits Menus
Selects or Adjusts
Features When
Menu is Displayed
Located On Remote Control
====
Selects Desired
>-- Feature When
Menu is Displayed
1. Press the ACTION button to display the Main Menu with Icons.
2. Press the CH UP or DOWN and the VOL LEFT or RIGHT buttons to select the desired Icon when the Main Menu
is displayed (selected Icon will be indicated in Red).
3. Press the VOL buttons for left and right movement and the CH buttons for up or down movement.
4. To exit the Main Menu first select the EXIT Icon, then press the ACTION button.
-14-

Picture Adjustments
• Color
• Tint
• Brightness
• Picture
• Sharpness
• Picture Norm
ACTION
Displays and Exits Menus
Located On Remote Control
Selects Desired
Menu is Displayed
Selects or Adjusts
Features When
Menu is Displayed
====
Helpful Hints:
Picture Adjustments:
COLOR -adjust for desired color intensity.
TINT - adjust for natural flesh tones.
BRIGHTNESS - adjust so dark areas of picture just
become black for a crisp detail.
PICTURE - adjust so the white areas of the picture are
to your liking.
SHARPNESS - adjust for best clarity of outline detail.
Color, Tint, Brightness, Picture &
Sharpness Adjustments
1. PresstheACTION buttontodisplay the Main Menu.
2. Press the CH DOWN button to select the Picture
Icon.
3. Press the ACTION button to display the Picture
AdjustmentMenu.
PICTURE NORM NO
COLOR Illlllllllall
TINT s
BRIGHTNESS IIIllllllllll
PICTURE IIIIIIIIIIIIIIIIIIIIIIIIII
SHARPNESS lllllllllllll
4. Press the CH UP or DOWN button to select the
desired Picture Adjustment (Color, Tint, Brightness,
Picture or Sharpness).
5. Press the VOL LEFT or RIGHT button to adjust your
selection. (The selected Picture Adjustment will be
displayed).
6. Repeat steps 4 and 5 for the remaining Picture
Adjustments.
7. Press the ACTION button twice to exit the Picture
Adjustment Menu.
Picture Norm -This feature is used to reset
Color, Tint, Brightness, Picture and Sharpness
adjustments back to a factory preset level.
1. Pressthe ACTION buttonto display the Main Menu.
2. Press the CH DOWN button to select the Picture
Icon.
3. Press the ACTION button to display the Picture
AdjustmentMenu.
_ IPICTUREI
PICTURE NORM
COLOR
TINT
BRIGHTNESS
PICTURE
SHARPNESS
.o :I
IIIIIit11111
IIIIIIIIIIIII ....... i
IIIIIIIIIIIIIIIIIIIIIIIIII
IIIIIIIIIIIII ....... J
-15-
4. Press the CH UP or DOWN button to highlight
"PICTURE NORM" (if necessary).
5. Press the VOL LEFT or RIGHT button to select
"SET" to Normalize Color, Tint, Brightness, Picture
and Sharpness.
6. Press the ACTION button twice to exit the Picture
Adjustment Menu.

Game Guard
ACTION
Displays and Exits Menus
Game Guard J| L 1_
_LOCKOUl[) -Prevents video
games and other video sources from being viewed.
Channel 3, 4 and all video inputs are locked out for 12,
24 or 48 hours.
NOTE: Be sure to understand this feature before
attempting its use. Use a code that you will
easily remember.
1. Pressthe ACTION buttontodisplaythe Main Menu.
2. Press the CH DOWN button to select the Game
Guard Icon.
3. Press the ACTION button to display the Game
Guard Menu.
Located On Remote Controt
Selects or Adjusts
Features When
Menu is Displayed
Selects Desired
Menu is Displayed
GAMEGUARDI
LOCK CH 3, 4, AND VIDEO INPUTS
HOW LONG? 12 HOURS
ENTER CODE ---
SET NO
4. Press the VOL RIGHT button to select the desired
hours (12, 24 or48) for Game Guard (Lockout) to be
activated.
5. Press the CH DOWN button to select "ENTER
CODE". Then enter a 3 digit code with the Remote
Control Keyboard.
IMPORTANT NOTE: Use a code you can easily
remember.
6. Press the VOL LEFT or RIGHT button after entering
three digit code. "Game Guard Locked" will display
On Screen.
GAME GUARD
LOCKED
Game Guard Activated
-16-

Game Guard (Unlock)
To unlock the Game Guard feature, repeat steps 1
through 3. Enter the same 3 digit code previously used
in step 5 with Remote Control Keyboard.
LOCK ACTIVATED
ENTER CODE TO CHANGE SETTINGS
Enter Same 3 Digit Code Previously Used
GAME GUARD
UNLOCKED
If 3 Digit Code Is The Same
INVALI D CODE
ENTERED
If 3 Digit Code Is Not The Same
-17-

Timer Features
• Sleep Timer
•Program Timer
ACTION
Displays and Exits Menus
Located On Remote Control
SelectsorAdjusts
FeaturesWhen
MenuisDisplayed
Selects Desired
Feature When
Menu isDisplayed
Sleep Timer-This feature is used for automatic
turn off in 30, 60 or 90 minutes.
NOTE: Display willflash 3, 2 and 1 toindicatethe last
three remaining minutes priorto turn off.The
Recall display willalso appear.
1. Press the ACTION button to display the Main
Menu.
2. Press the CH DOWN button to select the Timer
Icon.
3. Press the ACTION button to display the Timer
Control Menu.
--_ I TIMER CONTROL I
SLEEP TIMER NO
PROGRAM TIMER
ON
OFF
CHANNEL 3
SET NO
4. Press theVOL RIGHT button toselect 30, 60 or 90
minutes (Sleep Timer willbe activated).
5. Press the ACTION button twice to exit the Timer
Control Menu.
NOTE: To deactivate Sleep Timer repeat steps 1
through 4. In step 4 select =NO" instead of
minutes.
Helpful Hints:
Press the RECALL button to display the remaining
minutes for Sleep Timer, the time will display in the
bottom left corner.
-18-

Program Timer
ACTION
Displays and Exits Menus
Located On Remote Control
Selects Desired
Feature When
Menu is Displayed
Program Timer -This feature is capable of
turning the TV on, tunedto a desired channel and off at a
predetermined time (one day or everyday).
NOTE: The clock must be set for this feature to operate.
(Refer to the Set-Up Menu to set time.)
1. PresstheACTION buttontodisplay the Main Menu.
2. PresstheCH DOWN buttontoselectthe Timer Icon.
3. Press the ACTION button to display the Timer
Control Menu.
1TIMER CONTROL I
SLEEP TIMER NO
PROGRAM TIMER
ON
OFF
CHANNEL 3
SET NO
Selects orAdjusts
FeaturesWhen
Menu is Displayed
4. Press the CH DOWN button to select "ON" (time).
5. Press the VOL LEFT or RIGHT button repeatedly to
set hours(set AM/PM accordingly).
6. Press the CH DOWN button to select the minutes
position.
7. Pressthe VOL LEFT or RIGHT button repeatedly to
set minutes.
8. Pressthe CH DOWN button toselect "OFF" (time).
9. Repeat steps 5 through 7 for setting "OFF" (time).
10. Pressthe CH DOWN button to select =CHANNEL".
11. Press the VOL LEFT or RIGHT button or use the
Remote Control Keyboard to enter the channel
number desired when the set turns =ON".
12. Press the CH DOWN button to select "SET".
13. Press the VOL RIGHT button to select:
•NO - not activated.
• ONE DAY- activated.
• EVERY DAY - activated.
NOTE: Todeactivate Program Timer select "NO" in step
13.
14. Press the ACTION button twice to exit the Timer
Control Menu.
Helpful Hints:
• If you see "GAME GUARD" in the upper right hand
corner, the channel or Video Input you have selected
ha.s been locked out.
• If the Program Timer "ON" functions while the set is
operating, the set will automatically tune to the chan-
nel designated in the Timer Program.
-19-

Set-Up Features
• Menu
• CC (Closed Caption) on Mute
• Set "13me
•Antenna (TV or Cable)
•Auto Program
•Manual Program
•CC (Closed Caption) Mode
Menu -The Main Menu can be displayed in two
formats. Icon with Text or Icon without Text for those
familiar with the Icon system.
1. Press the ACTION buttonto display the Main Menu.
2. Press the CH DOWN and VOL RIGHT buttons to
select the Set-Up Icon.
3. Press the ACTION button to display the Set-Up
Menu.
ACTION
Displays and Exits Menus
Located On Remote Control
MENU ICON+TEXT
[_TON MUTE NO
TIME : AM
ANTENNA CABLE
AUTO PROGRAM NO
MANUAL PROGRAM NO
['_ MODE OFF FIELD 1
Selects Desired
Feature When
Menu is Displayed
4. Press the VOL LEFT or RIGHT button to select
ICON with TEXT or ICON only.
5. Press the ACTION button twice to exit the Set-Up
Menu.
Selects or Adjusts
Features When
Menu is Displayed -_1 EX,TI I INPUTI[_]
I-_-I IP'CTUREI I AUD'O I_
I_1 IGAMEIICHANNELII GUARDI ICAPTIONI _
[_ I TIMER I ISET-UPI _-_1
Icon with Text
D Fa
Icon (Only)
- 20-