Perrin & Rowe Armstrong 4599HT Operation manual

Perrin and Rowe is a registered trademark. 9004599 Issue 1
SPARES
Armstrong Kitchen Pot Filler
4599HT - Handle Textured
4599HS - Handle Smooth
Perrin & Rowe products are manufactured in the UK, using the latest technology
and built to the highest quality standards.
We would like to thank you for purchasing a Perrin & Rowe product and take this
opportunity to invite you to look at other luxury products by us. Please contact us
to receive our latest product catalogue.
GUARANTEE & LIABILITY
Your Perrin & Rowe product has been manufactured to exacting standards. However, in the unlikely event that you should experience any defect,
the following guarantees will apply:
Your Perrin & Rowe product is guaranteed against any mechanical defect within five years of the date of purchase. Should a fault occur; a free
replacement part will be issued. In the event that this does not resolve the defect, a replacement product will be supplied.
The surface finish of Perrin & Rowe products are guaranteed for one year from the date of purchase. This is provided our care and maintenance
instructions have been followed and that no scouring or aggressive cleaning agents have been used.
This does not affect your statutory rights. For full terms and conditions please contact Perrin & Rowe.
* Where indicated please specify colour
The Armstrong Kitchen Collection
Installation & User Guide
Temp Range:
Min 1°C (34°F)
Max 70°C (158°F)
Recommended
Working Pressure:
Min 1Bar (15psi)
Max 5 Bar (72psi)
Ideal performance obtained with equal hot & cold pressures.
SPARE PARTS & SERVICE
Phone: [phone]
[e-mail]
www.perrinandrowe.co.uk
• 4599HT
• 4599HS
• 4899
G1/2" BSP
O30mm
HOLE
•
•
Juliet Kitchen Pot Filler
4899
9.18798
9.18590*
(U.4599)
9.13249
(4599)
9.21231
9.01535* - Smooth
9.01536* - Textured
9.01472* - Smooth
9.01471* - Textured
9.13459*
(4599)
9.25599
9.15799
9.54799
SERVICEKIT
9.13199
(U.4599)
9.13899*
(4899)
9.18899*
(4899)
9.21231
9.12898
(4899)
9.01291*
(4899)
9.01204*
(4899)
9.01291*
(4899)
9.01204*
(4899)
9.13246
(4899)

CARE & MAINTENANCE
• Wipe down after use to avoid water spotting and mineral build up.
• Occasional cleaning with warm soapy water, followed by a polish with a soft cloth
is all that is required to keep the plated finish in good condition.
Do not use proprietary abrasive liquids, powders, or pads to clean the shower. Do not use any products with ammonia
bleach or limescale remover. You will damage the plated finish and void your guarantee.
1
2
Wall Mount Installation
BEFORE USE
• Carefully check the installation for leaks.
• If further building work is to be carried out in the vicinity, cover the product with a
plastic bag to avoid damaging the finish and prevent and debris entering rough
installation.
• Please ensure that the installation complies with local plumbing codes.
Congratulations on the purchase of your Perrin & Rowe Armstrong Kitchen Product. Correctly installed and with sensible care, this product will
give you many years of trouble free service.
IMPORTANT INFORMATION
Before you proceed... We recommend you engage the services of a registered plumber to install this product.
In addition to the guide below it is essential that the written information overleaf is carefully read and understood.
Please check that the contents of your Perrin & Rowe product are complete. Please check before you install the product that there is no damage to
the contents as we cannot accept any responsibility after installation.
Flush the plumbing system before
installing the bathroom product.
We recommend that the hot and cold
supplies should have conveniently placed isolating valves to
accomodate any servicing requirements.
Preparation Check Box for Installer
Installation - Pot Filler Trim
The Kitchen Collection
Installation & User Guide
• Screw the BSP inlet feed onto
the inlet shank using a 1/2" AF
Allen Key. Screw backnut onto
inlet shank for reinforcement.
WATER IN
½" BSP
INLET
FEED
• Position plumbing to suit
installation, taking into
account the suitable height and
reach.
• Remove 1/2" BSP wall connector
from pot filler assembly.
• Ensure black rubber O
Rings are fitted at positions
A and B on the BSP inlet
feed. Check they are
undamaged and free from any
debris.
Ensure all connections are firmly tightened.
1/2" INLET
SHANK
A B
WALL FIXING
FLANGE
• Once tightened adjust so that the
wall fixing flange is level. Place a
spirit level onto the flat of the
wall fixing flange.
• Adjust the depth of the fixing
flange accordingly.
• Secure the wall fixing flange to
the wall with the supplied
screws. Alternatively, please use
the correct fixing to suit the
installation.
WATER IN
BACK
NUT
30
O
mm
HOLE
• Once the BSP connector is fixed to
wall surface, position the rosette
onto the valve body. Ensure all O
Rings are correctly installed as
shown in diagrams.
• Keeping the rosette loose on the
valve body install the pot filler onto
the wall connector and securely fix
with the 2 concealed fixing screws.
Ensuring that the srews are secured
firmly into the keyway.
• Slide the rosette over the
concealed fixing screws until
it is flush with mounting
surface.
ROSETTE
IMPORTANT: Ensure fixing screws are fully tightened
using maximum leverage.