Pila Ssp User manual

INSTALLATION GUIDE

Football –7.32m x 2.44m Portable Goal Posts

Thank you for choosing PILA’s Australian Made products. If you need further advice during installation phone 1300 00 7452.

The information in this document is general advice only, not engineer’s advice or certification. PILA does not warrant the accuracy of this information and will not be held liable for its content or outcomes.

The product must be assembled correctly and maintained on a regular basis by checking all joints, bolts, screws, clips and nets.

Failure to do so may void the warranty. This product is a 2-person assembly.

PARTS LIST –PAIR OF 2 GOAL POSTS

ITEM

SPECIFICATION

QUANTITY

Upright

2430mm x 120/100mm powdercoated tube

Crossbar

3650mm x 120/100mm powdercoated tube (2-piece)

Joining Bolts

M8 x 90mm stainless screw & M8 x 20mm stainless barrel nut

12 ea

Allen Keys

5mm allen key & T-40 key

2 ea

Ground Sleeve

450mm x 120/100mm tube

Top Cap

50mm x 81mm tube & welded cap

Security Screw

M6 x 25mm stainless screw

Security Key

T-30 key

NET SUPPORTS

Net Supports

Triangle Net Supports

Bracing Bar

700mm Brace Bar

Hex Nut & Bolt

26mm alloy hex nut & M8 x 16mm hex head stainless bolt & washer

12 ea

Galvanised Bolt

M8 x 60mm galvanised bolt, washer & nut

•Lay out all components in the shape of the goal. Per end there will be 2 x uprights (part#3), 2 x sections to make the crossbar (part#1), elbows (part#4) and crossbar adapter fitted into the

crossbar (part#2).

•Connect the 2 sections of the crossbar (part#1) using the adapter (part#2) which will be already pre-connected to one of the sections. Make sure each crossbar section is matched up with

corresponding section (all sections are numbered). Connect the other side of the crossbar join using 2 x M8 x 90mm s/s allen key bolts and 2 x M8 x 20mm s/s counter sunk star torx barrel

nuts (part#13). Tighten both bolts firmly using keys supplied.

•Insert into the upright posts net track (part#3) 2 large alloy hex nuts (part#14) and leave them on the upper end of post towards the elbow. Thesehold the bottom of the D net support (part#5)

and the top of the rear support bar (part#7).

•Connect the D net supports (part#7) to the lug on the elbows (part#4) using the M8 x 60mm gal hex bolts with flat and spring washers (part#16). The bottom side of each D net support

(part#5) must be connectedtothe large alloy hex nut(part#14) previously inserted on the upright post (part#3) by usingthe M8 x 16mm s/s hex head bolt with flat and springwashers(part#15).

INSTALLATION GUIDE

Football –7.32m x 2.44m Portable Goal Posts

Thank you for choosing PILA’s Australian Made products. If you need further advice during installation phone 1300 00 7452.

•Connect the D bracing bar (part #6) to the D net support (part#5) and crossbar (part #1) by using 1 x M8 x 60mm gal hex head bolt with washers and nuts (part #16) (to fix D net support

(part #4)) and 1 x M8 x 16mm s/s hex head bolt and washers (part #15) (to fix crossbar (part #1)). The large alloy nut (part#14) is already installed in the crossbar net track (part #1).

•Assemble the back base bar (part#9) (net track side facing up) by connecting the 2 rear base elements using the back base steel connecting bar (part#10). Loosen the 4 x M8 x 16mm s/s

hex head bolt and washers (part#15) on both back base bars (part#9). Pull out steel connecting bar (part#10) to black line on the bar. This is the centre point. Tighten 2 of x M8 x 16mm s/s

hex head bolt and washers (part#15) making sure they go through the back base bar to secure firmly in place. Slide other side of the back base bar (part#9) over the steel connecting bar

(part#10) and secure the bolts firmly.

•Connect the back base bar (part #9) to the inside of the side base bars (part #8) using 2 flat alloy fixing plate 1 on top and 1 on the bottom (part #12) and bolted using 4 x M8 x 90mm gal

through bolts and washers on each corner (part #22).

•Insert 3 large alloy hex nuts (part#14) into the net track side bars (part#8) (1 in the middle and 2 at the front). Attach the gal fixing plate (part #11) to the front side of the side base bar (part

#8) using 2 x M8 x 16mm s/s hex head bolts and washers (part#15) into the large alloy hex nuts (part #14) already in net track. The gal fixing plate (part #11) should be in line with the front

edge of the side basebar (part #8). Add a 3rd large alloy hex nut (part #14) to the vertical hole on the gal fixing plate (part #11) by using 1 x M8 x 16mm s/s hex head bolt and washers (part

#15). Keep this bolt very loose so it can slide easily insidethe net track of the upright post (part #3) of the main goal frame.

•Connect the rear support bar (part #7) to the side base bar (part #8) by using 1x M8 x 16mm s/s hex head bolt and washers (part #15) into the large alloy hex nut (part #14) already inserted

into side base bar (part #8). The rear support bar (part #7) will hold itself on a 45-degree angle with the 1 bolt fitting.

•2 people can now lift the completed base frame 90 degrees to a vertical position (1 person at each side base bar) and carefully slide the large alloy nut (part #14) attached to the gal fixing

plate (part #11) into the net track at the bottom of the upright post (part #3) of the main goal frame. Slide the side base frame into the net track until the bottom of the side base (part#8)

frame is flush with the bottom of the upright post (part #3) of the main goal. Tighten the M8 x 16mm s/s hex head bolt (part #15) to hold in position.

•Fix the other end of the rear support bar (part #7) to the upright post (part #3) of the main goal frame using the M8 x 16mm s/s hex head bolt (part #15) into the large alloy hex nut (part #14)

already inserted into the upright post (part #3) of main goal frame. Ensure the base frame assembly and the main goal frames are at right angles to each other before tightening all bolts.

The completed goal assembly can now be tuned upright into its finished position and all bolts can be tightened.

•The net clips (part #18) can now be fitted into the net tracks. 26 clips to be placed on each crossbar (part #1); 11 clips to be placed on each one of the upright posts (part #3); 18 clips to be

placed on back base bar; 6 clips to be placed on each side base bar. 4 clips will remain as spares. Place net clips sideways into track and turn 90 degrees to lock in place. Turning the net

clips in the track can be hard on fingers so use a screwdriver to lever them around. Lock net clips into position using s/s net clip screws (#19).

•Knock in plastic end caps (#20) into the end of side base bar (part #8).

•Insert anchor pegs (part #17) through anchor points in back base bar (part #9) and side base bars (part #8). Put 4 pegs on the rear base bar and 3 on each side base bar.

•Ensure goal frame is anchored securely to the ground before use and users are educated on safe portable goal post use.

Never swing or climb on goal post. Regularly check and maintain goal post prior to every use. Refer to your soccer Goal Post Handbook for more information.