Pinnacle Aero Bella AB-716-QH Manual

User’s Manual and
Operating Instructions
Infrared Quartz
Room Furnace
841000100-11
Model: AB-716-QH
Table of Contents
Safety Information.............................................................2
Product Features..............................................................2
Unpacking and Assembly..................................................2
Operating Instructions.......................................................3
Storage / Maintenance......................................................4
Troubleshooting...............................................................4
Warranty...........................................................................5
Heater is intended for residential use. Do not use outdoors.
IMPORTANT: Read and understand all of the
directions in this manual before starting the heater.
Improper use of this heater can cause serious injury.
Keep this manual for future reference.
CONSUMER: Retain this manual for future reference.
Pinnacle Products International, Inc. 668 Stony Hill Road #302 Yardley, PA 19067 USA
Phone: [phone] Fax: [phone] Web: www.pinnacleint.com Email: [email protected]
TM

Safety Information
- Do not block the intake openings or heated air flow in
any manner.
- Check the heater thoroughly for damage before each
use. DO NOT operate a damaged heater.
- Do not operate heater if the cord or plug is damaged.
- DO NOT modify this heater or operate a heater that has
been modified from it’s original state. Modifying this
heater will void your warranty and could result in injury
and/or death.
- Do not run heater cord below carpeting, throw rugs, run-
ners or similar coverings. Do not run heater cord below
furniture or any appliance. Be sure heater cord is out of
traffic areas.
- Do not use this heater in bathrooms, laundry rooms or
similar indoor locations where humidity is high.
- Never operate heater in or near a bathtub, shower or
swimming pool.
- Keep children and animals away from heater.
- Always set heater on a stable, level surface.
- Do not plug this heater into any other cord connect-
ed device such as a power strip, surge protector,
multiple outlet adapter, grounding adpater, outlet-
type air fresheners or extension cords. Plug the
heater cord directly into a 3-prong 120V 15 amp
grounded circuit receptacle.
- Never plug heater cord into a loose fitting or broken
receptacle.
- Never use this heater below a receptacle.
- Be sure heater is turned off and fan has completed its
cool down mode before unplugging heater.
- Do not operate this heater near any water.
- Keep heater area free from combustible materials such
as gasoline, paint thinners and other flammable vapors
and liquids. Dust is combustible. Do not use heater in
areas of high dust concentration.
- NEVER leave heater unattended.
- ALWAYS maintain proper distance from combustibles.
- Do not open this heater unless instructed by an author-
ized representative of the manufacturer. There are lim-
ited user-serviceable parts inside.
Minimum clearance from Combustibles:
TOP SIDES FRONT BACK
24” 12” 72” 36”
Product Features
4 Infrared quartz bulbs: Each infrared quartz bulb is
rated at 375W and warms the air as is passes through the
inner chamber.
Cross flow fan: The cross flow fan creates a wide flow of
air using a cylindrical-shaped impeller.
Delay start function: This function controls the cross flow
fan, and allows the infrared quartz bulbs to heat up before
the fan begins to circulate the air flow. The cross flow fan
will also continue to operate after the heater is turned off to
circulate the warm air out of the heater, cooling the unit
down.
Copper Plate: The Diathermanous copper plate is
constructed from red copper, to enhance and improve
efficiency.
LED Display: This displays the temperature and time.
Operating the heater can be done on the unit’s control
panel, or by remote.
Unpacking and Assembly
- Inspect heater closely for any damage that may have
occurred during shipping. If there is any damage, return
the heater to the place of purchase.
- Remove heater from carton by sliding it out of the box,
and inspect for damages (Save carton and packing
materials for later off-season storage).
- Remove all protective packaging protecting heater
during shipping.
Page 2 Aero Bella Infrared Quartz Room Furnace
If the information in this manual is
not followed exactly, a fire, electric
shock or explosion may result causing property dam-
age, personal injury or loss of life.
Do not operate this heater until you
have read, and thoroughly under-
stand these safety and operating instructions.
Only persons who can read and understand these
instructions should use or service this heater.
WARNING
WARNING
NEVER LEAVE HEATER
UNATTENDED WHILE
OPERATING
Infrared Quartz
Room Furnace
TM

Operating Instructions
NOTE: “UP” and “DOWN” arrow buttons on the control
panel and remote control have dual function capabilities:
Use the UP arrow to adjust TIME / TEMP, or HI / LOW
settings.
Use the DOWN arrow to adjust TIME / TEMP, or °C / °F
settings.
1.Plug the power cord directly into a conventional 120V 15
amp grounded outlet and press the MASTER POWER
switch on the back of the heater.
2.Press the POWER button on the front control panel or
on the remote control to start the heater. The LED will
display the default setting (72°F / 22°C).
NOTE: If the current ambient temperature is greater than the
set temperature, the HI / LOW display, fan and Quartz
bulbs will not operate.
To alternate between F° and C°:
1.Pressing the °C / °F / Down button, you can switch the
temperature format from Fahrenheit to Celsius, and vice
versa.
To set Timer:
1. Pressing the TIME button, the LED display will switch
from the temperature status to the TIME status and
begin to flash. The default time will display “-” which
means the TIME is not activated, and the heater will
remain on.
2.You must press the HI/LOW/UP button or the
C°/F°/DOWN within (5) seconds to set the time. Each
time you press the HI/LOW/UP button, the time will
increase by 0.5 hours. Pressing C°/F°/DOWN will
decrease by 0.5 hours. The maximum amount of time is
8 hours; once you reach 8.0, the time will return to “-”
and start at 0.5 again.
3.Holding down each button (for 2 seconds) while setting
the time will change the time quicker. If no button is
pressed within (5) seconds, the time status will switch
back to the temperature status.
To set Temperature:
1. Pressing the TEMP button, the LED display will switch
to the TEMP status and begin to flash. You must press
the HI/LOW/UP button or the C°/F°/DOWN within (5)
seconds to set the temperature.
2. Pressing the the HI/LOW/UP button will increase the
temperature setting by 1°. Pressing the C°/F°/DOWN
button will decrease the temperature setting by 1°. The
maximum temperatuse setting is 86°F (30°C).
3. Holding down either button while setting the
temperature will increase or decrease the temperature
quicker. If no button is pressed within (5) seconds, the
time status will switch back to the temperature status.
To set Heat Output:
1. The default setting is HI. Press the HI/LOW/UP button
to switch from HI (1500W) to LOW (750W).
To calibrate Temperature setting:
1. Hold down the TEMP button for (5) seconds to switch to
thermostat calibration status. The LED display will
begin to flash. The default setting on the display is 00.
2. Press the the HI/LOW/UP or C°/F°/DOWN buttons to
scroll up or down for the correct calibration. The
displayed temperature should match your wall or
free-standing thermometer within (4) degrees.
3. Once the desired temperature is set, press TEMP button
to save your settings
NOTE: To reset back to factory settings, press and hold the
TIME button for (5) seconds.
To turn heater off:
1.Press POWER button on control panel or remote
control. Fan will continue to run in cool down mode.
2.When fan has shut down, you can unplug heater.
Aero Bella Infrared Quartz Room Furnace Page 3
Figure 1. LED Display
Do NOT turn off MASTER POWER
switch or unplug heater until the fan
has shut down! If prematurely turned off, the heater
can overheat, which may damage your heater and
void your warranty.
CAUTION
NEVER LEAVE HEATER
UNATTENDED WHILE
OPERATING
Infrared Quartz
Room Furnace
TM

Maintenance / Storage
NOTE: Before care or maintenance is applied, be sure
heater is not plugged in.
The cabinet housing can be wiped down with a damp cloth
or with furniture polish. Your heater comes with a
washable filter. The filter should be cleaned regularly for
maximum performance. Remove the filter from the heater,
and run warm water over and through filter to remove dirt
and dust. If desired you can use a mild soap to help
remove dirt and dust. Shake water from filter and replace
in heater (a damp filter can be replaced into the heater).
NOTE: Repair of this heater should be done by a quali-
fied service person.
It is recommended that you save all of the packaging
materials that came with your heater, and re-package the
heater using these materials for safe storage.
Debris, dust and dirt inside of the heater body can affect
the performance of your heater. This debris can impair the
heaters ability to draw air for ventilation.
Page 4 Aero Bella Infrared Quartz Room Furnace
Replacement Parts List
Item
Number
Part Description Part Number
1Remote Control 84-001-0100
2Filter 84-002-0100
3Castor 84-003-0100
4Quartz Bulb 84-005-0100
The Manufacturer reserves the right to make any changes in materials, specifications, prices or design without notice.
The Manufacturer may also discontinue items at any time.
Problem Possible Cause Solution
Heater does not turn on 1. No power from outlet
2. Not pluged in
3. MASTER POWER switch is off.
4. TIME is flashing on LED
1. Be sure outlet is in working order.
2. Be sure heater is plugged in.
3. Press MASTER POWER switch.
4. Press POWER button to turn off TIME and
resume normal operation of the heater.
Heater continues to operate
after power switch is turned
off.
1. Heater is in cool down mode 1. Do not unplug the heater. The fan will continue to
operate even after the power switch is turned off.
The heater is in cool down mode. Once the fan
has stopped, it is safe to disconnect the power
cord.
The amount of heated air
leaving the front of the
heater is reduced.
1. Filter is dirty
2. Vents are blocked
1. Check your electrostatic filter to make sure it is
free from dust and dirt, and clean if necessary.
2. Be sure the front grille and rear vent intake are
not being blocked.
Troubleshooting Guide
NEVER LEAVE HEATER
UNATTENDED WHILE
OPERATING
Infrared Quartz
Room Furnace
TM

Aero Bella Infrared Quartz Room Furnace Page 5
1 YEAR LIMITED WARRANTY
Pinnacle Products International, Inc. warrants this product to
the original retail purchaser only, to be free from defects in
material and workmanship for a period of one (1) year from the
date of initial purchase. This product must be properly installed,
maintained and operated in accordance with the instructions
provided.
Pinnacle Products International, Inc. requires reasonable proof
of your date of purchase from an authorized retailer or distributor.
Therefore, you should keep your sales slip, invoice, or cancelled
check from the original purchase. This Limited Warranty shall be
limited to the repair or replacement of parts, which prove
defective under normal use and service within the warranty
eriod, and which Pinnacle Products International, Inc. shall
determine at its reasonable discretion.
This warranty does not apply to products purchased for rental
use.
This Limited Warranty does not cover any failures or operating
difficulties due to normal wear and tear, accident, abuse, misuse,
alteration, misapplication, improper installation or improper
maintenance and service by you or any third party. Failure to
perform normal and routine maintenance on the heater, shipping
damage, damage related to insects, birds, or animals of any kind,
and damage due to weather conditions are also not covered. In
addition, the Limited Warranty does not cover damage to the
finish, such as scratches, dents, discoloration, rust or other
weather damage, after purchase.
All transportation costs for the return of the damaged product or
parts will be the responsibility of the purchaser. Upon receipt of
damaged item, Pinnacle Products International, Inc. will
examine the item and determine if defective. Pinnacle Products
International, Inc. will repair or replace and return the item,
freight pre-paid. If Pinnacle Products International, Inc. finds
the item to be in normal operating condition, or not defective, the
item will be returned freight collect.
This Limited Warranty is in lieu of all other express warranties.
Pinnacle Products International, Inc. disclaims all warranties
for products that are purchased from sellers other than author-
ized retailers or distributors.
AFTER THE PERIOD OF THE ONE (1) YEAR LIMITED WAR-
RANTY EXPIRES, Pinnacle Products International, Inc. DIS-
CLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR
APPLICATION. FURTHER, Pinnacle Products International,
Inc. SHALL HAVE NO LIABILITY WHATSOEVER TO
PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL,
INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES. Pinnacle Products International, Inc. assumes no
responsibility for any defects caused by third parties. This Limited
Warranty gives the purchaser specific legal rights; a purchaser
may have other rights depending upon where he or she lives.
Some states do not allow the exclusion or limitation of special,
incidental or consequential damages, or limitations on how long a
warranty lasts, so the above exclusion and limitations may not
apply to you.
Pinnacle Products International, Inc. does not authorize any
person or company to assume for it any other obligation or
liability in connection with the sale, installation, use, removal,
return, or replacement of its equipment, and no such
representations are binding on Pinnacle Products International,
Inc.
Always be sure to specify model number and serial number when
making any claim with Pinnacle Products International, Inc.
For your convenience use the space provided below to list this
information:
Model #: AB-716-QH
Serial #: _____________________
Date of Purchase: _________________
NEVER LEAVE HEATER
UNATTENDED WHILE
OPERATING
Infrared Quartz
Room Furnace
TM