Pioneer AVIC-F80DAB User manual

Black plate (1,1)
Installation Manual
NAVIGATION AV SYSTEM
AVIC-F80DAB
AVIC-F980DAB
English
<CRB4794-A>1

Black plate (2,1)
Precautions
Your new product and this manual 3
Important safeguards 3
Connection
Precautions before connecting the
system 5
Before installing this product 5
To prevent damage 6
–Notice for the blue/white lead 6
Parts supplied 7
Connecting the power cord (1) 8
Connecting the power cord (2) 10
Connecting the system 12
Connecting to separately sold power
amp 13
Connecting an iPod / iPhone or an Android
device 14
Connecting an iPhone with Lightning
connector 15
–Connecting via the USB port
(iPhone) 15
–Connecting via the HDMI port
(iPhone) 15
Connecting an iPhone with 30-pin
connector 16
–Connecting via the AUX input
(iPhone) 16
–Connecting via the RGB input
(iPhone) 16
Connecting the Android™device 17
–Connecting via the HDMI port (Android
device) 17
–Connecting via the MHL port (Android
device) 17
Connecting via the USB port (Android
device) 18
Securing the High Speed HDMI®Cable 18
Connecting a rear view camera 19
Connecting the external video
component 20
–Using AV input 20
–Using an AUX input 21
Connecting an HDMI device 22
Connecting the rear display 22
–When using a rear display connected to
rear video output 22
Installation
Precautions before installation 23
To avoid electromagnetic interference 23
Before installing 23
–For AVIC-F80DAB users 24
Installing this product 24
–Installation notes 24
–Parts supplied 25
–Installation using the screw holes on
the side of this product 25
Installing the GPS aerial 26
–Installation notes 26
–When installing the aerial inside the
vehicle (on the dashboard or rear
shelf) 27
Installing the microphone 28
–Parts supplied 28
–Mounting on the sun visor 28
–Installation on the steering column 29
–Adjusting the microphone angle 29
After installation
After installing this product 30
<CRB4794-A>2
Contents
Engb
2

Black plate (3,1)
Your new product and this
manual
!The navigation features of this product
(and the rear view camera option if pur-
chased) are intended solely to aid you in
the operation of your vehicle. It is not a sub-
stitute for your attentiveness, judgement
and care when driving.
!Never use this product to route to hospi-
tals, police stations, or similar facilities in
an emergency. Please call the appropriate
emergency number.
!Do not operate this product, any applica-
tions, or the rear view camera option (if pur-
chased) if doing so will divert your attention
in any way from the safe operation of your
vehicle. Always observe safe driving rules
and follow all existing traffic regulations. If
you experience difficulty in operating this
product or reading the display, park your
vehicle in a safe location and apply the
handbrake before making the necessary
adjustments.
!This manual explains how to install this
product in your vehicle. Operation of this
product is explained in the separate man-
uals.
!Do not install this product where it may (i)
obstruct the driver’s vision, (ii) impair the
performance of any of the vehicle’s operat-
ing systems of safety features, including
airbags, hazard lamp buttons, or (iii) impair
the driver’s ability to safely operate the vehi-
cle. In some cases, it may not be possible
to install this product because of the vehi-
cle type or the shape of the vehicle interior.
!Model icons shown in this manual indicate
that the description is intended for the
models indicated by the icons.
If the following icon is shown, the descrip-
tion is applied only to the model shown.
e.g.)
F80DAB
!The graphical symbol placed on
the product means direct current.
Important safeguards
WARNING
Pioneer does not recommend that you install
this product yourself. This product is de-
signed for professional installation only. We
recommend that only authorised Pioneer ser-
vice personnel, who have special training
and experience in mobile electronics, set up
and install this product. NEVER SERVICE
THIS PRODUCT YOURSELF. Installing or
servicing this product and its connecting
cables may expose you to the risk of electric
shock or other hazards, and can cause da-
mage to this product that is not covered by
warranty.
!Read this manual fully and carefully before
installing this product.
!Keep this manual handy for future refer-
ence.
!Pay close attention to all warnings in this
manual and follow the instructions care-
fully.
!This product may in certain circumstances
display inaccurate position of your vehicle,
the distance of objects shown on the
screen, and compass directions. In addi-
tion, the system has certain limitations, in-
cluding the inability to identify one-way
streets, temporary traffic restrictions and
potentially unsafe driving areas. Please ex-
ercise your own judgement in the light of
actual driving conditions.
!As with any accessory in your vehicle’s in-
terior, this product should not divert your
attention from the safe operation of your
vehicle as it may result in serious injury or
death. If you experience difficulty in operat-
ing the system or reading the display,
please make adjustments while safely
parked.
!Please remember to wear your seat belt at
all times while operating your vehicle. If
you are in an accident, your injuries can be
considerably more severe if your seat belt
is not properly fastened.
<CRB4794-A>3
Engb 3
Section
01
Precautions
Precautions

Black plate (4,1)
!Certain country and government laws may
prohibit or restrict the placement and use
of this product in your vehicle. Please com-
ply with all applicable laws and regulations
regarding the use, installation and opera-
tion of this product.
<CRB4794-A>4
Engb
4
Section
01 Precautions

Black plate (5,1)
Precautions before
connecting the system
WARNING
Do not take any steps to tamper with or dis-
able the handbrake interlock system which
is in place for your protection. Tampering
with or disabling the handbrake interlock
system could result in serious injury or
death.
CAUTION
!If you decide to perform the installation
yourself, and have special training and ex-
perience in the mobile electronics instal-
lations, please carefully follow all of the
steps in the installation manual.
!Secure all wiring with cable clamps or
electrical tape. Do not allow any bare wir-
ing to remain exposed.
!Do not directly connect the yellow lead of
this product to the vehicle battery. If the
lead is directly connected to the battery,
engine vibration may eventually cause
the insulation to fail at the point where
the wire passes from the passenger com-
partment into the engine compartment. If
the yellow lead’s insulation tears as a re-
sult of contact with metal parts, short-cir-
cuiting can occur, resulting in
considerable danger.
!It is extremely dangerous to allow cables
to become wound around the steering col-
umn or gearstick. Be sure to install this
product, its cables, and wiring away in
such so that they will not obstruct or hin-
der driving.
!Make sure that the cables and wires will
not interfere with or become caught in
any of the vehicle’s moving parts, espe-
cially the steering wheel, gearstick, hand-
brake, sliding seat tracks, doors, or any of
the vehicle’s controls.
!Do not route wires where they will be ex-
posed to high temperatures. If the insula-
tion heats up, wires may become
damaged, resulting in a short circuit or
malfunction and permanent damage to
the product.
!Do not cut the GPS aerial cable to shorten
it or use an extension to make it longer.
Altering the aerial cable could result in a
short circuit or malfunction.
!Do not shorten any leads. If you do, the
protection circuit (fuse holder, fuse resis-
tor or filter, etc.) may fail to work properly.
!Never feed power to other electronic pro-
ducts by cutting the insulation of the
power supply lead of this product and tap-
ping into the lead. The current capacity of
the lead will be exceeded, causing over-
heating.
Before installing this product
!Use this product with a 12-volt battery and
negative earthing only. Failure to do so may
result in a fire or malfunction.
!To avoid shorts in the electrical system, be
sure to disconnect the (–) battery cable be-
fore installation.
<CRB4794-A>5
Engb 5
Section
02
Connection
Connection

Black plate (6,1)
To prevent damage
WARNING
!Use speakers over 50 W (maximum input
power) and between 4 Wto 8 W(impe-
dance value). Do not use 1 Wto 3 Wspeak-
ers for this product.
!The black lead is earth. Please earth this
lead separately from the earth of high-cur-
rent products such as power amps. Do not
earth more than one product together
with the earth from another product. For
example, you must separately earth any
amp unit away from the earth of this pro-
duct. Connecting earths together can
cause a fire and/or damage the products if
their earths became detached.
!When replacing the fuse, be sure to only
use a fuse of the rating prescribed on this
product.
!When disconnecting a connector, pull the
connector itself. Do not pull the lead, as
you may pull it out of the connector.
!This product cannot be installed in a vehi-
cle without ACC (accessory) position on
the ignition switch.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
!To avoid short-circuiting, cover the discon-
nected lead with insulating tape. It is espe-
cially important to insulate all unused
speaker leads, which if left uncovered may
cause a short circuit.
!Attach the connectors of the same colour
to the corresponding coloured port, i.e.,
blue connector to the blue port, black to
black, etc.
!Refer to the owner’s manual for details on
connecting the power amp and other units,
then make connections accordingly.
!Since a unique BPTL circuit is employed,
do not directly earth the *side of the
speaker lead or connect the *side of an-
other side of the speaker lead together. Be
sure to connect the *side of the speaker
lead to the *side of the speaker lead on
this product.
Notice for the blue/white lead
Important
When this product is in “Power OFF”mode, the
control signal is also turned off. If “Power OFF”
mode is cancelled, the control signal is output
again and the aerial is extended with the auto aer-
ial function (if the aerial is being used). Be careful
so that the extended aerial does not come into
contact with any obstacles.
!When the ignition switch is turned on (ACC
ON), a control signal is output through the
blue/white lead. Connect to an external
power amp’s system remote control term-
inal, the auto-aerial relay control terminal,
or the aerial booster power control terminal
(max. 300 mA 12 V DC). The control signal
is output through the blue/white lead, even
if the audio source is switched off.
!Be sure not to use this lead as the power
supply lead for the external power amps.
Such connection could cause excessive
current drain and malfunction.
!Be sure not to use this lead as the power
supply lead for the auto-aerial or aerial
booster. Such connection could cause ex-
cessive current drain and malfunction.
<CRB4794-A>6
Engb
6
Section
02 Connection

Black plate (7,1)
Parts supplied
This product Power cord
GPS aerial Microphone
Mini-jack extension
cable
USB cable
Lock tie Vehicle Bus conversion
cable
Metal sheet Clamp (3 pcs.)
Double-sided tape
<CRB4794-A>7
Engb 7
Section
02
Connection
Connection

Black plate (8,1)
Connecting the power cord (1)
Depending on the types of vehicles, the
function of *2 and *4 may be different. In this
case, be sure to connect *1 to *4 and *3 to *2
as shown in the figure.
Connect leads of the
same colour to each other.
Yellow (*2)
Back-up
(or accessory)
Red (*4)
Accessory
(or back-up)
Yellow (*1)
To terminal supplied with
power regardless of ignition
switch position.
Red (*3)
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (earth)
To vehicle (metal) body.
Note
In some vehicles, the ISO connector may be divided
into two. In this case, be sure to connect to both
connectors.
Note
*2 *1
*4 *3
ISO connector
Speaker leads
White: Front left 
White/black: Front left 
Grey: Front right 
Grey/black: Front right 
Green: Rear left 
Green/black: Rear left 
Violet: Rear right 
Violet/black: Rear right 
<CRB4794-A>8
Engb
8
Section
02 Connection

Black plate (9,1)
Note
The pin position of the ISO connector will differ
depending on the types of vehicles. Connect *5
and *6 when Pin 5 is an aerial control type. In
other types of vehicles, never connect *5 and *6.
Yellow/black (MUTE)
If you use equipment with a mute function, connect
that equipment to the Audio Mute lead. If not, keep
the Audio Mute lead free of any connections.
Power cord
Audio source will be set to mute or attenuate, while the
following sounds will not be muted or attenuated. For details,
refer to Operation Manual.
— Voice guidance of the navigation
— Incoming ringtone and incoming voice of the mobile phone
that is connected to this product via Bluetooth wireless
technology
This product
14 cm
Fuse (10 A)
Blue/white (*5)
Blue/white (*6)
To auto-aerial relay control terminal or
aerial booster power control terminal
(max. 300 mA 12 V DC).
Power supply
<CRB4794-A>9
Engb 9
Section
02
Connection
Connection

Black plate (10,1)
Connecting the power cord (2)
Pink (CAR SPEED SIGNAL INPUT)
This product is connected here to detect the distance the vehicle travels. Always connect the
vehicle’s speed detection circuit. Failure to make this connection will increase errors in the
vehicle’s location display.
LIGHT GREEN LEAD AT POWER CONNECTOR IS
DESIGNED TO DETECT PARKED STATUS AND MUST BE
CONNECTED TO THE POWER SUPPLY SIDE OF THE
HANDBRAKE SWITCH. IMPROPER CONNECTION OR
USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW
AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.
Light green (PARKING BRAKE)
Used to detect the ON/OFF status of the handbrake. This lead must be connected to the power supply side
of the handbrake switch.
If this connection is made incorrectly or omitted, certain functions of this product will be unusable.
Power supply side
Earth side
Handbrake switch
Connection method
Clamp the lead of the power supply
side of the handbrake switch.
Clamp firmly with needle-nosed
pliers.
The position of the speed detection circuit and the position of the handbrake switch vary
depending on the vehicle model. For details, consult your authorised Pioneer dealer or an
installation professional.
Note
WARNING
CAUTION
It is strongly suggested that the speed pulse wire be connected for accuracy of navigation
and better performance.
IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE OR INJURY INCLUDING
ELECTRICAL SHOCK, AND INTERFERENCE WITH THE OPERATION OF THE
VEHICLE´S ANTILOCK BRAKING SYSTEM, AUTOMATIC GEARBOX AND
SPEEDOMETER INDICATION.
WARNING
<CRB4794-A>10
Engb
10
Section
02 Connection