Play Mor Space Saver User manual

Space Saver
Attachment Beam
Assembly Instructions

STEP #2
Position the Space Saver Attachment Beam as pictured below. Center it from left to right on the
Tower and align its front face with the front face of the Upper Rim 2x6 of the Tower.
STEP #1
Center the Logo Plaque above one of the
swing positions on what will be the
most visible side of the Beam. Fasten
it to the Beam with 4 — 2¼” screws.
HARDWARE
(THIS PAGE)
4 — 2¼” SCREWS

STEP #3
Fasten a small Corner Brace on either side
of the Beam at both sides of the Tower.
Study photo at right and below for
placement details. Fasten each brace
with 2 — 4” screws.
STEP #4
Fasten a 2x6x10¼” Bracing Piece at one corner
on the outer side of the Beam as pictured at
right. Pre-drill ten 5/32” pilot holes (one at
each screw position). Fasten the Bracing Piece
to the Beam and the Upper Rim 2x6 with 10
— 2¼” screws. Repeat at the opposite end
with another Bracing Piece.
HARDWARE
(THIS PAGE)
20 — 2¼” SCREWS
8 — 4” SCREWS
END VIEW

STEP #5
Due to the extra force that is exerted on the Tower by the swinging motion of the swings on the
Space Saver Attachment Beam, extra bracing is necessary. The Watch Tower instruction man-
ual details the bracing instructions necessary for installing a normal Attachment Beam at one
side of the Tower. Since the Space Saver Attachment Beam extends from both sides of the
Tower, repeat the bracing instructions given in the Watch Tower instruction manual at both
sides of the Tower. (See Step #4 and Step #13 in the Watch Tower instruction manual. Photos
below are from that manual.)
LONG SIDE OF THE FLOOR
EXTRA LONG CORNER BRACES ON BOTH SIDES
EXTRA LONG
CORNER BRACES
EXTRA LONG CORNER BRACES ON BOTH SIDES

A. Drill an angled 5/32” pilot hole at each end of the
Corner Braces. Insert a 4” screw in each pilot hole as
you fasten each brace in place as pictured at right. You
will use a total of 8 — 4” screws.
HARDWARE
(THIS PAGE)
4 — 3” SCREWS
8 — 4” SCREWS
STEP #6
Finish bracing the Tower by installing four extra long Corner Braces at Floor level (two per side).
Follow the lettered steps below.
B. Finish fastening each brace by inserting a 3” screw
through the face of the brace and into the corner upright
of the rail. Be sure to pre-drill a 5/32” pilot hole be-
fore inserting each screw.
PRE-DRILL A PILOT HOLE.
INSERT A SCREW.
OUTSIDE VIEW

STEP #7
Anchor the tower with four Stakes. The Stakes should be on the inside of the Sandbox. Allow at
least an inch of Stake above ground and fasten each one to the Sandbox with 2 — 2¼”
screws. Since the Stakes need to be installed on the sides of the Tower that will best counter-
act the effect of the swing motion, be sure to place them on the short sides of the Sand-
box (the sides of the Tower from which the Slide and Ladder extend).
HARDWARE
(THIS PAGE)
8 — 2¼” SCREWS

“Our son loves his play set. The quality is way more than
I expected. I see no need for improvement. Would recom-
mend to anyone. ”
- Heather Linder, Clayton, OH
“The playset is lovely! Our daughter enjoys playing on it
everyday! We are impressed with the craftsmanship of
the playset and the courteous staff who put it together.”
- Len & Brittany Oxley, Hillsboro, OH
“We are pleased with our new play set! The product
quality is excellent as was the entire customer service ex-
perience. Many thanks!”
- Annie O’Leary, Beaver, PA
“Everything was great! Our new swingset is amazing
and our son loves it! Installation went quick and easy.
Great family investment!”
- Barry & Ami Huffman, Portland, IN