PlayAlive Spider Guide

Installation and assembly instruction v4
Spider
®

Content
1
1. Content
2. Component overview
2.0 Content of transport case
2.1 - 2.8 Component overview
3. Site of spider construction
3.1 Maximum length of power cable
3.2 Measurements of impact area
3.3 Foundations
4. Mounting of steel construction
4.1 Support of the center ring
4.2 Mounting of rear left leg (Leg C)
4.3 Mounting of rear right leg (Leg D)
4.4 Mounting of two middle legs (Leg B + E)
4.5 Mounting of two front legs (Leg A + F)
5. Mounting of net
5.1 Mounting of side nets
5.2 Mounting of top net
5.3 Mounting of rear net
6. Electronics
6.1 Pulling of devicenet cable
6.2 Pulling cables inside the legs
6.3 Mounting of satellites placed in the legs
6.4 Mounting of satellites on the body of the Spider
7. Plastic parts
7.1 Mounting of plastic shells
7.2 Mounting of plastic bracket
8. Verifying dimensions / casting foundations
8.1 Verifying dimensions
8.2 Casting the concrete
9. For the electrician
9.1 Installing cabinet with power outlet for PlayAlive power supply
9.2 Services, PC connection
9.3 Electrical specications
10. Start up
10.1 Start up the system
10.2 Select and start game
10.3 Reset the game
10.4 Idle mode
10.5 Adjust volume if needed
11. Appendix
11.1 General introduktion to PlayAlives Technology Platform
11.2 Conduit pipes and PlayAlive technology
11.3 Games

Component overview
2
1 x Center ring
P-MA002
2 x Midle leg
(leg B + E)
P-MA004
2 x Inner plugs B
(for conncetor tubes)
P-MM017
1 x Rear left leg
(leg C)
P-MA005
20 x Self tapping screw 4 x 20 mm
P00142
1 x Rear right leg
(leg D)
P-MA006
2.1 Steel structures (placed in transport case) (P00091)
2.2 Inner plugs for connector tubes (P00094)
2.3 Plastic brackets (P00083)
2.0 Content of transport case
The spider product arrives in a big wooden box / transport case. The box contains the steel
structures as well as eight smaller boxes. The contents are specied below.
1 x Front left leg
(leg A)
P-MA003
8 x Inner plugs A
(for conncetor tubes)
P-MM016
1 x Front right leg
(leg F)
P-MA007
4 x Connector tube
(for side mounting)
P-MA011
12 x Casting anchor
P00115
1 x Rear connector tube
P-MA010
6 x Button Head M6 x 16 mm
P00009
6 x Plastic bracket
P-MP015
6 x Washer M6
P00141
Important!
Check the packing list.
– Due to model varia-
tions, actual content
may differ from the
illustration
2.8
Accessory kit
2.2
Inner plugs
2.3
Plastic
Brackets
2.7
Adapter
2.5
Tecnology kit 1
2.5
Tecnology kit 2
2.5
Tecnology kit 3
2.4
Net
2.6
Plastic shells
2.1 Steel Structures

16 x Satellite
P00020
48 x Countersunk screw
M5 x 12 mm
P00077
1 x Bottom plastic shell
P-MP012
4 x Inner adapter
P-MM038
3 x 2 m Data cable
P00254
1 x Termination
P00252
1 x Top plastic shell
P-MP011
4 x External adapter
P-MM037
1 x Manual
P00144
40 x Rubber strips
P00117
1 x Glue
P00011
1 x Grease
P00010
1 x Drill 3.5mm
P00119
TX 25
P00005
Component overview
2
2.5 Tecnology kit 1-3 (P00124)
2.6 Plastic shells (body of Spider) (P00075)
2.7 Satellite adapters for body of Spider (P00079)
2.8 Accessory kit (P00095)
7 x 3,5 m Data cable
P00255
5 x 7 m Data cable
P00263
1 x Devicenet cable 33 m
power- and datacable
P00258
1 x 230 AC cable
(EU + UK)
22 x Buttonhead M5 x 12 mm
P00076
24 x Buttonhead M5 x 16 mm
P00007
24 x Washer M5
P00143
1 x Rear net
P-MZ002
117 x Shackles
P00122
2.4 Net (P00092)
4 x Top net
P-MZ003
4 x Side net
P-MZ001
1 x Power supply
(IPSU)
P00251

3.3 Foundation
Size of foundations
3.2 Measurement of impact area
3.1 Maximum length of power cable
Site of Spider construction
3
Tip:
Tip:
For details on cable pipes see the technicial
details in section 11.
max. 25 m
404 cm
R: 285 cm
Ø: 570 cm (Diameter)
Ø: 70 cm
95 cm
70 cm
65 cm
All legs are prepared
for cables to be pulled
inside the legs.
Verify dimensions:
Distance from the
center of the Spider
to the edge of the
impact area = min.
480 cm measured
parallel to any leg.
50 cm (recommended)
Power Supply Box
Distance between power supply and
the closest leg must not exceed 25 m
Soil or sand
Casting anchor
Impact area
Impact surface
marking
Center of hole
All measures are based on the center of the hole.
219 cm
Important!
Remember pull wire
in cable pipe.
ground
150 cm
954,7 cm
section B - B
B
B
L
L
Ø 9547
R 1500 typ. 6
Cable pipe diameter: Ø 28/34 mm

Center ring
Leg
Mounting of steel construction
4
The installation will become easier by using
a support table for correct placing and leveling
of the center ring.
Important!
Important!
Important!
Important!
Note that there are 5 dif-
ferent legs. It is important
that they are assembled
correctly in order for nets
and connector tubes to
be mounted. Check label
on the legs.
All bolts, nuts and
threads must be lubri-
cated with the supplied
grease.
Remember to install the
casting anchors.
The 4 narrowly placed
holes on the center ring
should face forward.
1 x Center Ring
1 x Rear left leg (leg C)
Top of impact area
2 x Washer M16 2 x lock nut M16
143 cm
4.1 Support of the center ring
4.2 Mounting of rear left leg (Leg C)
A C B+E D F
2 x Casting anchor
Installed
casting anchors

4.3 Mounting of rear right leg (Leg D)
4.4 Mounting of two middle legs (Leg B + E)
4.5 Mounting of two front legs (Leg A + F)
1
2
2 x Middle leg (leg B + E)
2 x Connector tube
2 x Connector tube
1 x Rear right leg (Leg D)
Front left leg (leg A)
Front Right leg (leg F)
2 x Inner plug B
4 x Inner plug A
4 x Inner plug A
1 x Rear connector tube
2 x Washer M16
4 x Washer M16
4 x Washer M16
2 x Lock nut M16
4 x Locking nut M16
4 x Locking nut M16
4 x Self tapping screw
4 x 20 mm
8 x Self tapping screw
4 x 20 mm
8 x Self tapping screw
4 x 20 mm
Important!
The Inner plugs must
be predrilled with a
3.5 mm drill before
the self tapping screws
are installed.
2 x Casting anchor
4 x Casting anchor
4 x Casting anchor

Mounting of nets
5
5.1 Mounting of side nets
5.2 Mounting of top net
5.3 Mounting of rear net
4 x Side net
4 x Top net
1 x Rear net
76 x Shackle
28 x Shackle
9 x Shackle
Important!
Shackles must be secured
with the supplied glue.

0
Satellite with ID 0
Electronics
6
6.1 Pulling of devicenet cable
6.2 Pulling cables inside the legs
Cable from knee to foot (3,5 m)
Cable from foot to neighbour
knee (7 m)
Devicenet cable from power supply
(IPSU) to satellite 0
1 x Devicenet cable cable 33 m
6 x 3,5 m Data cable
5 x 7 m Data cable
1 x 33 m Devicenet cable
Important!
The connectors must be kept dry
and free from dirt, sand and soil.
The cables must be handled with
care and must never be pulled in
the plugs.
1 x 230 AC cable
c
The cable must be pulled in the leg closest to
the power supply box
a
a + b + c must not exceed 28m
b
Power cabinet
min. 40 x 40 cm
1 x Power supply
(IPSU)
5 cm
230V
Power supply
(IPSU)
Tip:
When installing the cables inside
the tubes of the spider, it can be
of advantage to pull them two
at a time. This makes them less
exible and easier to pull.
Tape

6.3 Mounting of satellites placed in the legs
12 x Satellite
Important!
Important!
All satellites have an
ID number which can
be found on the bot-
tom of the satellite. The
ID-number determines
where the satellite must
be placed on the Spider.
(see the illustration)
Satellites must be
wired using serial
connection – Please,
carefully follow the
illustration below.
Use termination plug to
nish the ID 2 satellite.
30 x Countersunk screw M5 x 12 mm
5 4
11 10
12 9
13 8
6 3
7 2
0
14 15
1
7
6
54
3
2
13
12
11 10
9
8
1
15
0
14
5 4
11 10
12 9
13 8
6 3
7 2
0
14 15
1
1
15
14
0
8
13
Cable from knee to foot (3,5 m)
Cable from foot to neighbour
knee (7 m)
Devicenet cable for power supply
(IPSU)
Cable for connecting the eyes (2 m)

3 x 2 m data cable1 x 3,5 m data cable
6.4 Mounting of satellites on the body of the Spider
20 x Buttonhead
M5 x 16 mm
4 x Satellite
ID 15
ID 1
ID 14
ID 0
Important!
Satellites and adapters
must be assembled so
the logo is oriented
correctly.
1 x Lower plast shell
1 x Upper plast shell
4 x Inner adaptor
4 x External adaptor
Upper plast shell
Lower plast shell
20 x Washer M5
Important!
Section 6.3 shows how
to connect the cables
between ID 0,1,14 and 15.
12 x Countersunk screw
M5 x 12 mm

7.1 Mounting of plastic shells
7.2 Mounting of plastic brackets
Plastic parts
7
Lower plast shell is mounted
on the center ring.
Upper plast shell is mounted
on the center ring.
6 x Plastic brackets
20 x Buttonhead M5 x 12 mm
6 x Buttonhead M6 x 16 mm
Important!
Important!
Remember to lubricate
the screws with the sup-
plied grease.
Due to manufacturing
tolerances on the plastic
shells, it may be neces-
sary to install rubber
strips between the center
ring and plastic shell.
6 x Washer M6
40 x Rubber strips
Tip:
When installing the rubber
strips, start at the front as
shown in the illustration.

160 cm .
Verifying dimensions / casting foundations
8
8.1 Verifying dimensions
8.2 Casting the concrete
Important!
Remember to verify the dimen-
sions before casting the concrete.
Tip:
After legs have been founded with
concrete, the play area must be
blocked off with a ribbon marker.
The equipment can be used 24
hours after completion of the
foundations.
Verify that the casting anchors
are in the right position.
Important!
Important!
To ensure the correct distance
between the legs, a temporary
spacer may be placed as
illustrated.
654,1 cm
466,3 cm
142,7 cm
241,7 cm
Impact surface
227,7 cm
227,7 cm
227,7 cm
(center to center
of net connector)
Casting anchors
142,7 cm
Impact surface
marking
Impact surface
70
55 40
Impact area
Concrete
Casting
anchors

For the electrician
9
PlayAlive spider uses a 230VAC -> 24VDC power supply. A cabinet containing at
least 1 pcs 230V AC power outlet must be installed. Ground connection needed.
The cabinet must be installed by the customer’s electrician. The cabinet can be
placed indoor or outdoor depending on the customer’s request.
IMPORTANT: When identifying the proper location of the power supply
cabinet it is crucial to note that the 24V DC power cable has a maximum
length of 33 meters. The 33-meter cable should cover the distance from
the Spider’s head, through the legs, distance in the ground and connec-
tion in the cabinet!
Typical specications for the cabinet:
Dimensions: 400 x 400 x 250 mm (Power supply dimensions: 263 x 183 x 91 mm.
Vandalism proof metal cabinet with at least 1 key lock.
At least 1 (preferable 2-3) socket(s) with ground installed in the cabinet.
9.1 Installing cabinet with power outlet for PlayAlive power supply
9.2 Services, PC connection
9.3 Electrical specications
Cabinet with power outlet
min. 40 x 40 cm
5 cm
230V
Power supply
(IPSU)
Optional: A timer controlling the electricity (power on/off)
can be added to the cabinet. Please see illustration of standard
timer that can be installed in a 110 V/230 V power outlet.
The timer need to be sourced locally. When applying a timer
the power can be switched off for examble at night time.
The optional timer
could look like this.
Services and access to a PC should only be done by PlayAlive trained staff.
Type: PlayAlive Spider
Input: 100-240VAC, 50/60Hz, 5.4 A
Secondary: 24VDC, 0-13,4 A short circuit protected
Power Consumption: Max 240W

Start up
10
In idle mode all satellites lights up individually and can be used indi-
vidually. This mode is often a hit for minor children and designed to
create awareness.
The platform will go in idle mode if games are not selected. The
system will turn off and only wake up every now and then and show
colors to attract attention. Touching any satellite will bring the system
back and you willl be able to select games at the select game console.
Thanks for your effort installing another PlayAlive product.
10.1 Start up the system
Turn the power on at the IPSU. The satellites boot up and after few
minutes the power supply box should indicate two green lights. The
system is now ready to play.
10.2 Select and start game
10.3 Reset the game
10.4 Idle mode
Place your hand app. 5 seconds on the satellite with ID 1 (placed at the right corner
of the spiders body.) The game is terminated and the satellite will toggle between
the 3 different game colors where after a new game can be selected.
To adjust the volume, follow this procedure:
1. Turn off power
2. Turn on power
3. Wait until the system is ready for game selection (sat. 0 and 1 will
be in “scroll and a selection” mode)
4. Touch and hold sat. 00 (lower left satellite in body) - not later than 30
seconds after the scroll and selection menu appears after restart
5. Touch sat. 01 (lower right satellite) for a short while (when still holding sat. 00)
6. The system will respond “set volume” – release the hand from sat. 00
7. Touch sat. 01 for volume adjustment
8. For each touch on sat. 01 a sound will be played and volume level will be
indicated on the satellite
9. When the preferred volume level has been reached sat. 00 must be touched
for storage
10. Volume has been adjusted and stored
NOTE: It is rather important to have a certain sound level in order
to experience the full joy of the individual PlayAlive activities.
If you have been able to conduct the elements as described at section
10.1 - 10.3 the PlayAlive site has beeen successfully installed.
10.5 Adjust volume if needed
Green lights
1. Power must be turned on
2. If satellites are ashing a color the game is in idle mode and ready
for game selection and start
If satellites are in “sleep” mode touch any satellite to make the satellites
ready for game selection and start
3. Go to the body of the Spider and look at the two satellites in the lower part
4. Use the left satellite (seen from the players view) to toogle between the
three different games. Each touch on the left satellite will show a new game
color on the right satellite
5. Touch the right satellite when the desired game it highlighted
6. Game will start

The PlayAlive system is an interactive system. The technology elements
communicate with each other and thereby make it possible to realize
activities for all ages.
The visible part of the installation is the “satellites”. The satellites are
intelligent units that contain light, sound, touch sensor, and communica-
tion. They act as the user interface to the system. Cables connected to
satellites supply them with power and communication.
IMPORTANT: BE CAREFUL WHEN HANDLING THE PARTS.
The PlayAlive technology elements are highly advanced electronics. De-
spite the fact that they are very robust after installation, they can easily
be damaged before or during installation if not treated correctly.
NOTE: ALL PARTS ARE DESIGNED TO FIT TOGETHER WITHOUT THE
NEED OF USING FORCE.
When using exible cable pipes it is important to ensure that the
minimum bending radius complies too the following:
For our devicenet cables, we recommend 28/34 mm exible cable
pipe / conduit pipe with double walls for easy pulling of the cables.
Please note that low cost cable pipes are very soft and therefore very
easy to bend in inappropriate radiuses – they are not recommended!
It is further recommended to place covers over the ends of the cable
pipes during the period from installation of the pipes to installation of the
electronics to avoid water in the pipes.
When installing the cable pipes it is recommended to ensure that care is
taken to ensure that the pulling string in the pipes are kept available. It
makes pulling the cables a lot easier. If this is not possible, then we rec-
ommend that you use vacuum (ex. a vacuum cleaner) to suck a pulling
string through. It has proven easier than other methods.
In some cases it is possible to push the cable through the pipes without
other help. In cases where this is not possible, it is recommended to use
a pulling string.
Please be aware that the PlayAlive cables are not designed to be pulled
in the connectors. When pulling the cables please make sure that you
pull the cable and not the connector.
Appendix
11
11.1 General introduction to PlayAlives Technology Platform
11.2 Conduit pipes and PlayAlive technology
Important!
Remember devicenet
cables in conduit pipe.
Conduit pipe needs to
be sourced locally.

11.3 Games
Please see the instructions for the different games below:
Additional games can be ordered at PlayAlive.
Hot & Cold Two persons or two teams play each other. Red against
blue team. The team who hits the most satellites during
30 seconds will win.
High energy, fun and competition – and simple.
Speedy
ChaosTennis
Free Play
Hit as many satellites as possible during 30 seconds
and beat the high score.
High energy and improve your high score. Fun for
many kids at the same time.
Beat your best friend or dad in a game of Squash. The
game is adaptive and will adjust speed to level of the
players.
High speed game for two or four players. Length of the
game depends on the players ability.
Each satellite will have its own play mode with funny
sounds, music tunes and light creation. Will cease
when games are started.
Lightshow
2-satellite interface
After 2 minutes of no activities all satellites will go in
sleep mode. Every 15th minutes a light show will go on
for 10 seconds.
The lightshow will be customized to the individual
product/conguration.
Games will be selected and started on two satellites
placed at the lower part of the spiders body. A simple
interface supported by an intuitive sign with icons and
QR codes will help guide the users through the various
games and start the desired games.