PlayNation Play Systems Tahoe Space Saver User manual

ASSEMBLY MANUAL
Copyright © 2010 PlayNation Play Systems, Inc.
All Rights Reserved
www.PlayNation.com • 190 Etowah Industrial Court • Canton, GA 30114 • [phone]
Latest Revision: November 24, 2010
Tahoe Space Saver

Warranty and Safety Guidelines……………………………………..….....……...Pages 3-10
Leveling You Playset, General Information, Denitions and Site Plan......... Pages 10- 14
Kit Contents and Tool List…………..………………………………………...............Page 15
Hardware, Lumber and Accessory Checklist......……………………………....Pages 16-20
Framing Fort……………………………………..…………………………..……..... Steps 1-3
Mounting Deck Supports…………………………....……………….…………...…...... Step 4
Attaching Center Posts……………....…………………...…..……..……...….……..... Step 5
Attaching Tire Swing Support.............................……………………..……............... Step 6
Attaching Tire Swivel and Blocks...………….……………………..…….................… Step 7
Adding Deck Panels/End Center Posts/Center Deck Board…….…......…...... Steps 8-10
Adding Side Rails and Trapeze Arms…………………………………....…........Steps 11-12
Attaching Ladder………………...…………………………….........................…....... Step 13
Attaching Side Panels and Rear Panels................................................................ Step 14
Attaching Tarp Boards and Tarp..................................................................... Steps 15-16
Mounting Slide.………………………………………………………….....………....... Step 17
Mounting Filler Board, Swings, Fort Supports and Safety Boards................. Steps 18-21
Adding Steering Wheel, Telescope, Safety Handles...................................... Steps 22-24
Flag Kit and Name Plate Installation...............................………………………..Steps 25-26
Warranty Card.....................................................................................................Last Page
PLEASE READ OWNER’S MANUAL CAREFULLY
BEFORE STARTING ASSEMBLY!
TABLE OF CONTENTS
Page 2
2

Page 3
IMPORTANT – PLEASE READ
As fresh lumber acclimates to its new environment, the natural tendencies of the tree
can show itself in the form of checks, or “cracks” in the lumber. In almost all cases this is
normal and it will not affect the structural integrity of your play set.
Cosmetic defects that do not affect the structural integrity of the product, or natural
defects of wood such as warping, checking or any other physical properties of wood that
do not present a safety hazard, are not covered by this warranty. Defects that develop
because the product is exposed to extreme climate conditions are not covered by this
warranty. Defects that develop as a result of faulty or improper installation of the product
are also not covered by this warranty.
Most cracks are not warrantable, however if you believe that the integrity of your
play set is compromised by this natural occurrence, please follow the warranty claim
procedure found at www.playnation.com. Click on the “Customer Care” tab on the left
hand side of the page, then click on “Warranty Claim” and follow the instructions.
We appreciate your purchase and know that you will enjoy your play system for many
years to come.
IF YOU HAVE MISSING OR DAMAGED PARTS OR NEED ASSISTANCE
ASSEMBLING, PLEASE CALL PlayNation Play Systems, Inc. MANUFACTURING
DIRECT.[phone] FACTORY HOURS – MON.–FRI., 8AM-5PM EST DO NOT
RETURN THIS PRODUCT TO THE RETAILER OR CONTACT THE RETAILER
DIRECT. THE RETAILER DOES NOT STOCK COMPONENTS. PLEASE RETAIN
THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE
PLACE WHERE YOU CAN REFER TO THEM AS NEEDED.
CONTACT INFO:
PlayNation Play Systems, Inc.
190 Etowah Industrial Court
Canton, GA 30114
Tel. [phone]
Fax. [phone]
[email protected]
Check for revised instructions at www.playnation.com/instructions.html
3

Page 4
Thank you for choosing Playnation Play Systems, Inc.
We’ve included everything you need, except tools, to build your very own professional
looking play set. When complete, your new play set should far exceed the quality of
play set kits from other build-your-own companies. Our engineers and design team
have over 30 years of playground experience. What we’ve developed is a play set that
doesn’t compromise quality for simplicity. Yet you’ll appreciate how quick and easy
construction really is! Our play set kits are designed for children ages 3 to 11. Playnation
Play Systems, Inc. believes every child should have a play set and with our kits they
can! You can rest assured your new play set is safe, durable and designed to hold up to
the elements. As parents ourselves, we know how important the security and well- being
of our children is, and this shows in all of our products.
Each play set features our step-by-step 3D illustrated manual, patented powder coated
swing beam bracket, heavy-duty swing belts with chains, slide(s), accessories, plus all
the required hardware and pre-milled lumber.
4

Page 5
Limited Manufacturers Warranty
PlayNation Play Systems, Inc. (“PlayNation”) warrants its play sets to be free from
defects in workmanship and materials, under normal use and conditions at its original
installation, for 10 years for structural wood components and for one year for all other
components (e.g., hardware, plastics, tarps, rope ladder, etc.)
Cosmetic defects or natural defects of wood (e.g., warping, seasonal checking or
cracking, knots, or knot holes, etc.) that do not affect the structural integrity of the
product are not covered by this warranty. Defects that develop because the product is
exposed to extreme climate conditions, or that develop as a result of faulty or improper
installation of the product, are not covered by this warranty. Fading or discoloration of
any part or accessory, cracks in plastic components, surface rust on hardware, and
chips on powder coated materials are not considered defects in material as long as they
do not affect the functionality or structural integrity of the part or component.
It is the owner’s responsibility to properly maintain the play set. Instructions for proper
maintenance can be found on PlayNation’s website. Imperfections or defects that
develop because of a failure to properly maintain the play set are not covered by this
warranty.
PlayNation will repair or, at its discretion, replace any part within the stated warranty
period that is defective in workmanship or materials. This decision is subject to
verication of the defect, which, at PlayNation’s discretion, may be accomplished by
submitting photographs or by delivery of the defective part to PlayNation. Any warranty
claim must include proof of purchase, including the date of purchase.
This warranty is valid only if the product is used for the purpose for which it was
designed and installed at a residential, single-family dwelling. This warranty is void if the
product is used for commercial,institutional or multi-familling dwelling use. This warranty
does not cover (a) products that have been damaged by acts of God, negligence,
misuse, or accident, or that have been modied or repaired by unauthorized persons;
(b) the cost of labor; or (c) the cost of shipping the product, any part, or any replacement
product or part.
PLAYNATION DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES
OF ANY KIND, EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. GORILLA WILL NOT BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. This warranty is valid only in the United States
of America, is nontransferable and does not extend to the owners of the product
subsequent to the original purchaser, and only applies to the product as originally
installed (in other words, installing the product and then later disassembling and
reinstalling the product at the same or another location voids the warranty). Some states
do not allow limitations on implied warranties or exclusion of incidental or consequential
damages, so these restrictions may not be applicable to you. This warranty gives you
specic legal rights. You may also have other rights which vary from state to state.
5

Page 6
Important Safety Guidelines
This product is intended for residential use only and not intended for use in any public
setting. A safety surface such as mulch or recycled tire should be used under the play
set to prevent injury from falls. Also a 6 foot safety zone should be used around the
entire play set.
As with any home project, good judgment and respect for power tools will greatly reduce
the risk of injury. PlayNation recommends you follow all tool manufacturers’ safety
guidelines. Always wear eye protection and safety gloves to prevent injury. In several
phases of construction two people may be required for lifting and securing of lumber.
While play set is being constructed, please keep children off the equipment until the
project is complete. Bolts and screw heads should be checked regularly for tightness.
The ground ladder, rope ladder, slide, swings and other areas where children spend a
majority of their playtime should be checked more frequently.
PlayNation shall not be liable for incidental, indirect or consequential damages or
injuries that result from the building and/or playing on our play sets. Adult supervision is
recommended anytime a play set is being used.
WEIGHT LIMITS FOR PlayNation Play Systems
• FORT PLATFORMS: 800 LBS. TOTAL WEIGHT
• SWING BELTS: 175 LBS.
• GLIDER SWINGS: 70 LBS. PER CHILD
• TRAPEZE: 125 LBS.
• FULL BUCKET SWING: 50 LBS.
• TODDLER BUCKET SWING: 50 LBS.
• INFANT SWING: 35 LBS.
• TIRE SWING: 125 LBS. TOTAL WEIGHT
• ROPE LADDER: 75 LBS.
• ROCK WALL: 150 LBS.
• ALL SLIDES: 125 LBS.
PlayNation recommends that the weight limits for all components must not be
exceeded. Failure to adhere to these and other safety guidelines could result in damage
to the play set and injury to the users.
6

Page 7
Safety and Maintenance Tips for Your New Play Set:
NOTE: Your children’s safety is our #1 concern. Observing the
following statements and warnings reduces the likelihood of serious
or fatal injury. Please review these safety rules regularly with your
children.
• This play set is designed for the use of 4 occupants who have a combined weight not
exceeding 800 pounds on the elevated oor, 3 occupants who have a combined weight
of 525 pounds on the swing area, for a total unit capacity of 7 occupants who have a
combined weight of 1325. (this weight is not including the picnic table area)
• On-site adult supervision is required.
• Teach children not to walk close to, in front of, behind, or between moving swings or
other moving playground equipment.
• Teach children to sit in and never stand on swings.
• Teach children not to twist the chains and ropes and not to loop them over the swing
beam, since this may reduce the strength of the chain or rope.
• Teach children not to jump from swings or other playground equipment in motion.
• Teach children not to push empty seats. The seat may hit them and cause serious
injury.
• Teach children to sit in the center of the swings with their full weight on the seats.
• Teach children not to use the equipment in a manner other than intended.
• Teach children to always go down slides feet rst. Never slide headrst.
• Teach children to look before they slide to make sure no one is at the bottom.
• Teach children to never run up a slide, as this increases their chances of falling.
• The parents should have the children dress appropriately with well-tting shoes. Loose
clothing such as scarves and ponchos should not be worn. Always take off, tie up or
tuck in cords and drawstrings on children’s clothing. These things can get caught on
playground equipment and strangle a child.
• Teach children not to climb when the equipment is wet.
• Teach children to never jump from a fort deck. They should always use the ladder,
ramp or slide.
• Teach children to never crawl or walk across the top of monkey bars.
• Teach children to never crawl on top of a fort roof.
• Verify that any suspended climbing ropes, chains, or cables are secured at both ends.
• Verify climbing ropes are tight enough that they cannot be wrapped around an adult
hand.
• Teach children not to attach items to the playground equipment that are not specically
designed for use with the equipment, such as, but not limited to, jump ropes, clothesline,
pet leashes, cables and chain as they may cause a strangulation hazard.
• Teach children to never wrap their legs around swing chain.
• Teach children to never slide down the swing chain.
WARNING: Children must NOT use this play set until unit has been
completely assembled and inspected by an adult to insure set has
been properly installed.
7

Page 8
Safety and Maintenance Tips for Your New Play Set: (continued)
Playgrounds should be inspected on a regular basis. If any of the following conditions
are noted, they should be removed, corrected, or repaired immediately to prevent
injuries.
• Hardware that is loose, worn or that has protrusions or projections.
• Exposed equipment footings.
• Scattered debris, litter, rocks, or tree roots.
• Splinters, large cracks, and decayed wood components.
• Deterioration and corrosion on structural components, which connect to the ground.
• Missing or damaged equipment components, such as handholds, guardrails, swing
seats.
• Check all nuts and bolts frequently during the usage season and tighten as required.
(But not so tight that you crack the wood) We recommend you check the swing beam
and hardware often due to wood expansion and contraction. It is particularly important
that this procedure be followed at the beginning of each season.
• Remove plastic swing seats and take indoors or do not use when the temperature
drops below 32°F.
• Oil all metallic moving parts monthly during the usage period.
• Check all coverings for bolts and sharp edges twice monthly during usage season to
be certain they are in place. Replace when necessary. It is especially important to do
this at the beginning of each new season.
• Check swing seats, ropes, cables and chains monthly during usage season for
evidence of deterioration. Replacement should be made of any swing seat that has
developed cracks in the plastic seats or has exposed metal in the edges of the swing
seat. If there are already exposed metal inserts on the edge of the seat, immediately
remove the seats and chains to prevent serious injury. Ropes, cables and chains should
be removed and replaced if excessive wear is found. Contact PlayNation for warranted
replacement parts.
• For rusted areas on metallic members such as monkey bars, hand supports brackets,
etc.; sand and repaint, using a non lead-based paint meeting the requirements of Title
16 CRF Part 1303.
• Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season
causing splinters to appear. Light sanding may be necessary to maintain a safe playing
environment. If you are treating your play set with stain regularly, it will help prevent
severe checking/splitting and other weather damage.
• Once or twice a year, depending on your climate conditions, you must apply some type
of protection (sealant) to the wood of your unit. Prior to the application of sealant, lightly
sand any “rough” spots on your set. Please note this is a requirement of your warranty.
• Creating and maintaining the play set on a level location is very important. As your
children play, your play set will slowly dig its way into the soil, and it is very important
that it settles evenly. Make sure the play set is level and true once each year or at the
beginning of each play season.
• Rake the playground surface periodically to prevent compaction and maintain
appropriate depths. Disposal Instructions: When the play set is no longer desired, it
should be disassembled and disposed of in such away that no unreasonable hazards
will exist at the time the unit is discarded.
8

Page 9
Play Set Surfacing Recommendations:
Below are some of the recommendations that the U.S. Consumer Product Safety
Commission (CPSC) offers from its Handbook for Public Playground Safety. The guide
can be downloaded in full at www.cpsc.gov/cpscpub/pubs/325.pdf
1. Protective Surfacing - Since almost 60% of all injuries are caused by falls to the
ground, protective surfacing under and around all playground equipment is the most
critical safety factor on playgrounds.
Certain manufactured synthetic surfaces also are acceptable; however, test data on
shock absorbing performance should be requested from the manufacturer.
Asphalt and concrete are unacceptable. They do not have any shock absorbing
properties. Similarly, grass and turf should not be used. Their ability to absorb shock
during a fall can be reduced considerably through wear and environmental conditions.
Certain loose-ll surfacing materials are acceptable such as the types and depths
shown in the table.
Fall Heights and Recommended Materials
Type Of Material 6 in. depth 9 in. depth 12 in. depth
Double-Shredded bark mulch 6’ Fall Height 10’ Fall Height 11’ Fall Height
Wood Chips 6’ Fall Height 7’ Fall Height 12’ Fall Height
Fine Sand 5’ Fall Height 5’ Fall Height 9’ Fall Height
Shredded Tires* 10-12’ Fall
Height
n/a n/a
Fine Gravel 6’ Fall Height 7’ Fall Height 10’ Fall Height
*This data is from tests conducted by independent testing laboratories on a 6-inch depth of uncompressed shredded tire samples
produced by four manufacturers. The tests reported critical heights, which varied from 10 feet to greater than 12 feet. It is
recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the
critical height of the material when it was tested in accordance with ASTM F1292.
It should be recognized that all injuries due to falls cannot be prevented no matter what
surfacing material is used.
9

Page 10
2. Fall Zones - A fall zone, covered with a protective surfacing material, is essential
under and around equipment where a child might fall. This area should be free of other
equipment and obstacles onto which a child might fall. Stationary climbing equipment
and slides should have a fall zone extending a Minimum of 6’ in all directions from the
perimeter of the equipment.
Swings should have a fall zone extending a minimum of 6’ from the outer edge of the
support structure on each side. The fall zone in front and back of the swing should
extend out a minimum distance of twice the height of the swing as measured from the
ground to the top of the swing support structure.
Leveling Your Fort During Assembly
• Complete the steps which will be the basic frame of the fort {i.e. four corner posts with
base (sand box boards) and deck supports}
• Position in the most level area chosen for the play set, keeping in mind the location
and size of the swing beam, ladder, slides, etc. that extend off the fort.
• Once the frame is in the nal position, check for vertical and horizontal levelness to
determine which side(s) will need to be dug into the ground to level the play set.
• With a shovel, score the ground around the outside edges of the sandbox boards on
the ‘high’ side of the fort. This is the area that will be dug in. Make sure to score deep
enough; the scored lines will be your digging template.
• Push the frame off and away from the scored area, far enough to dig and remove dirt
to reach the appropriate depth.
• Dig a channel along the scored line(s) for the base of the fort (corner post and
sandbox boards) to rest into. Dig the channel(s) to the same level depth. The bottom
of the channel(s) should be level to each other so your frame doesn’t teeter or rock
because the channel(s) are uneven.
• Once you have removed enough grass and dirt, slide/push the frame into the
channel(s). Place a level on the vertical and horizontal boards of the frame to determine
if enough soil, or too much, was removed.
• Repeat this process until the basic frame is plumb and level and in its nal position
before completing the rest of the assembly.
• Measure diagonally make sure fort is square.
Important: if you require a channel depth of more than 6”, then we
recommend you have your play set area professionally graded before
completing assembly.
= AREA TO BE SCORED AND
CHANNELED FOR LEVELNESS
THE DIAGONAL
MEASUREMENTS
SHOULD BE THE
SAME FROM
CORNER POST
TO CORNER
POST. IF NOT,
ADJUST FORT
SO THAT THE
DISTANCE IS
EQUAL.
Side View of
Playset Frame
(Grade is the
slanted line.)
Top View of
Playset Frame
showing diagonal
measurements.
10

Page 11
General Info to Review Before Installation
• Depending on your experience, assembly of PlayNation Playsets can take as little
as 6 hours up to 24 hours, depending on size, after inventory of parts; therefore, we
recommend you set aside a full two days for assembly.
• Identify all of the parts for your play set. Empty each box and lay out boards so you
can see each part. Your instruction book will have detailed drawings that will make it
easy for you to recognize individual parts. Keep all hardware and metal parts separate
from wooden pieces.
• After everything is laid out, check carefully to ensure all parts are present. Make sure
there are no broken boards.
• Find an area to sort your hardware. It is best to open the hardware on a solid surface
so that you do not lose any pieces in the grass. This will save time and familiarize you
with all the different pieces in the hardware bag.
• Important note: Wood has some natural defects such as knots, surface cracks, etc…
We reject parts that are structurally defective. We use a high quality lumber in our
structures; however, you should inspect each part for splinters or rough spots and sand
them smooth to prevent injury.
• After familiarizing yourself with all of the components, read all instructions thoroughly.
Reading instructions after you have studied the parts will help you understand more
clearly the installation process, and help to eliminate unnecessary mistakes.
• Pay close attention to the diameter and length of each bolt and screw.
• Never tighten hardware completely at rst. It helps to have some adjustment for bolt
alignment while you are attaching parts together. After everything is square, tighten
each joint.
• After the main unit is assembled it is critical that the oor is level and square. If the
main frame is not level, the walls and oor will be out of square.
• After you complete installation, make sure every bolt, screw, and nut is tight, and every
board is secure. Wood will expand and contract with the seasons.
• Check all bolt connections and swing hangers seasonally.
• Place the set on level ground, not less than 6ft from any structure or obstruction such
as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.
11

Page 12
This page is a list of denitions and explanations used throughout our
instructions to aid you in the assembly of your play set.
Offset Holes- Throughout the installation procedures we will refer to parts with offset
holes. This refers to the orientation of the holes on the board. An offset hole is one that
is closer to one side than it is to the other or in other words, it is not centered on the
board. In the procedures you will be instructed to attach the boards with the holes “offset
up” or with the holes “offset down”. This refers to which side of the board the hole/holes
should be closer to. Offset Holes Up= hole/holes will be closer to the top of the board.
Offset Holes Down= hole/holes will be closer to the bottom of the board. Note: some
parts do not have offset holes, but instead the holes are on center. Therefore there will
not be any reference to how to offset these parts.
EXAMPLE OF OFFSET HOLES DOWN
EXAMPLE OF OFFSET HOLES UP
Counter-sunk holes- Many of the parts that will be used have counter-sunk holes.
A counter-sunk hole is one that surrounds one side of a thru hole, but does not extend
through the wood it’s self. When using a counter-sunk hole the bolt will be inserted
through the thru hole. In some cases the bolt head with a washer will occupy the
counter-sunk hole. In other cases a nut with a washer will occupy the counter-sunk hole.
Lag Screws- Lag screws are used in the construction of our play sets to enhance
the structural integrity of the unit. There will not be predrilled holes in the post for lag
screw installation. Lag screws are self-tapping, though if you are using a manual socket
wrench it may be necessary to tap the head of the lag screw with a hammer. You
should also be sure to tighten the lag screws completely. Power tools such as an impact
wrench or power drill should have enough torque to drive the lag screws without using a
hammer, but make sure not to over tighten as this can cause the threads to “strip out” in
the post.
Thru Hole
Counter Sunk Hole
12

Page 13
Common Installation Practice Installing T-nuts
When installing T-nuts into the wood, use a smooth faced hammer to set the face of the
T-nut ush into the wood
Insert the barrel of the T-nut into the
predrilled hole. Using a smooth faced
hammer, drive the T-nut until the face
of the T-nut is ush to the wood.
This picture shows the T-nut insert
and installed ush to the wood.
This picture shows an end view of the T-nut
insert and installed ush to the wood.
WARNING: DO NOT EMBED THE TOP
OF THE T-NUT INTO THE
FACE OF THE WOOD
Cross Section end views, you are looking at an Xray view
of the post and T-nut. The barrel of the T-nut is in the
corner post. The line is the face of the wood.
Corner Post
T-nut
Flush
13

76.75 38.25
120.75
18.25
38.25
54.75
Please familiarize yourself with the manual, parts/components and general con-
struction process of your new playset before getting started.
SITE PLAN:
Playset height: 11-1/2 feet
Approximate assembly time: 6-8 Hours
6 foot unobstructed safety perimeter around playset recommended
Trapeze Arm (1)
Scoop Slide
Ladder
Swing Belts (1)
Page 14
14

Page 15Page 15
REQUIRED TOOL LIST:
___ Standard or Cordless Drill w/ Phillips Bit (#2 square bit provided)
___ 1/8” Drill Bit
___ 3/8” Drill Bit
___ ½” Wrench and Socket
___½” Deep Well Socket
___.9/16” Deep Well Socket
___ 9/16” Wrench and Socket
___ Level
___ Tape Measure
___ Extension Cord (if using standard drill)
___ Hammer
___ Pencil
___ Locking Pliers (Vise Grips)
___ Shovel
KIT CONTENTS
Swings, Slides, Accessories:
___ (Qty ) Description
___ (1) Swingbelts w/ Chains
___ (1) 10ft. Scoop Slide
___ (1) Tahoe Space Saver Assembly Manual
___ (1) Trapeze Swing
___ (1) Telescope
___ (1) Steering Wheel
___ (2) Safety Handles
___ (1) Plastic Flag Kit
___ (1) Tire Swing w/Chains
___ (1) Tarp with snaps
Fort Hardware:
see following pages
Wood Components:
see following pages
Swing Beam Hardware:
see following pages
15

3/8 X 3-1/2"
HEX LAG SCREW
QTY: 42
PLASTIC
BOLT CAP
QTY: 26
#14 X 1-1/4"
PAN HEAD SCREW
QTY: 7
#2 SQUARE
DRILL BIT
QTY: 1
3/8 X 5"
HEX LAG SCREW
QTY: 42
3/8 X 6-1/2"
CARRIAGE BOLT
QTY: 26
#8 X 2-1/2"
WOOD SCREW
QTY: 36
#8 X 2"
WOOD SCREW
QTY: 70
3/8" LOCK NUT
QTY: 26
3/8" WASHER
QTY: 110
TORQUE WASHER
QTY: 26
1
4
3
2
5
6
7
8
9
USE THE RULER TO THE RIGHT TO MEASURE YOUR BOLTS AND SCREWS. PICTURE VIEWS SHOWN
ABOVE ARE 1:1 SCALE AND CAN BE USED TO MATCH BOLT AND SCREW SIZES.
16

2 X 4 X 70"
CENTER DECK
SUPPORT
2
2 X 4 X 70"
SAFETY
BOARD/
CENTER
TARP
BOARD
3
5
2 X 6 X 70"
SANDBOX/FILLER
BOARD
2
4 X 4 X 16"
FORT SUPPORT
(LEFT)
2
4 X 4 X 16"
FORT SUPPORT
(RIGHT)
4
4 X 4 X 25"
BLOCK
2
2 X 4 X 77"
END TARP
BOARD
PICTURE DESCRIPTION QTY.
17

1
4 X 4 X 62-3/4"
TIRE SWING
SUPPORT
4 X 4 X 70"
BLOCK
SUPPORT
2
4 X 4 X 70"
DECK
SUPPORT
2
2
4 X 4 X 84"
CENTER POST
4 X 4 X 96"
CORNER
POST
4
2
4 X 4 X 118"
SIDE RAIL
4 X 6 X 38"
END CENTER
POST
2
PICTURE DESCRIPTION QTY.
18

4 X 6 X 115"
TRAPEZE ARM
2
5/4 X 6 X 63-1/2"
CENTER DECK
BOARD
1
2
2-3/8" X 16-7/8" X
69-1/2"
DECK PANEL
(3 BOARD)
2
2-3/8" X 11-1/4"
X 69-1/2"
DECK PANEL
(2 BOARD)
1
4-3/4" X 29" X 76"
LADDER
2
3-3/8" X 28-7/8" X
33"
BACK PANEL
4
3-3/8" X 29-3/4" X
31"
SIDE PANEL
PICTURE DESCRIPTION QTY.
19

TIRE SWIVEL
11-4010
1
SCOOP
SLIDE
03-0005
SPRING
CLIP
11-4003
STEERING
WHEEL
07-0004
TELESCOPE
07-0001
IRON
DUCTILE
11-4012
SAFETY
HANDLE
08-0001
1
7
4
1
1
2
PICTURE DESCRIPTION QTY.
20