Playnation COLOSSAL TAHOE User manual

COLOSSAL
TAHOE

STEP #1:
1. PLACE ONE 2 X 6 X 102 ½” SANDBOX BOARD FLUSH WITH
THE BOTTOM OF ONE 4 X 4 X 123” MIDDLE CORNER POST AND
ONE 4 X 4 X 123” REAR CORNER POST. LINE UP THE MIDDLE
CORNER POST WITH THE MIDDLE HOLES ON THE SANDBOX
BOARD AND THE REAR CORNER POST WITH THE HOLES 66 ½”
FROM THE MIDDLE HOLES ON THE SANDBOX BOARD. THE
SAND BOX BOARD SHOULD BE ON THE SIDE OF THE CORNER
POSTS WITH THE THROUGH HOLES. FASTEN THE SANDBOX
BOARD WITH 3 ½” LAG BOLTS AND 3/8” WASHERS.
2. REPEAT THIS STEP.

STEP #2:
1. ATTACH THE 4 X 4 X 126” LEFT TOP SIDE SUPPORT AND
RIGHT TOP SIDE SUPPORT TO THE CORNER POSTS AT THE
112” HOLE. FASTEN THE TOP SIDE SUPPORTS FROM THE
INSIDE WITH 6 ½” CARRIAGE BOLTS WITH ½” WASHERS
AND 3/8” WASHERS AND LOCKNUTS ON THE OUTSIDE.

STEP #3:
1. INSTALL 4 X 4 X 70” BLOCK SUPPORTS TO THE CORNER
POSTS AT THE 78” HOLES. FASTEN THE BLOCK SUPPORTS
FROM THE OUTSIDE WITH 6 ½” CARRIAGE BOLTS WITH ½”
WASHERS AND 3/8” WASHERS AND LOCKNUTS ON THE
INSIDE.

STEP #4:
1. PLACE 2 X 6 X 70” SAND BOX BOARDS FLUSH WITH THE
BOTTOM OF THE CORNER POSTS. FASTEN THE SANDBOX
BOARD WITH 3 ½” LAG BOLTS WITH 3/8” WASHERS.

STEP #5:
1. PLACE 4 X 4 X 70” DECK SUPPORTS ON TOP OF THE BLOCK
SUPPORTS. FASTEN THE DECK SUPPORTS TO THE CORNER
POSTS WITH 5” LAG BOLTS WITH 3/8” WASHERS.
2. FASTEN THE DECK SUPPORTS TO THE BLOCK SUPPORTS
WITH 5” LAG BOLTS WITH 3/8” WASHERS FROM
UNDERNEATH.

STEP #6:
1. PLACE THE 4 X 4 X 78” CENTER POSTS FLUSH WITH THE
BOTTOM OF THE BLOCK SUPPORTS, LINING UP THE PILOT
HOLES AT THE CENTER OF THE BLOCK SUPPORTS. FASTEN
THE CENTER POSTS TO THE BLOCK SUPPORTS FROM THE
OUTSIDE WITH 6 ½” CARRIAGE BOLTS WITH ½” WASHERS
AND 3/8” WASHERS WITH LOCKNUTS ON THE INSIDE.
2. FASTEN THE CENTER POSTS TO THE TOP SIDE SUPPORTS
WITH 5” LAG BOLTS AND 3/8” WASHERS.

STEP #7:
1. PLACE THE 4 X 4 X 62 ¾” TIRE SWING SUPPORT FLUSH ON
TOP OF THE BLOCK SUPPORTS, IN LINE WITH THE CENTER
POSTS. NO SCREWS ARE NEEDED FOR THE TIRE SWING
SUPPORT.

STEP #8:
1. PLACE THE 2 X 4 X 70” CENTER DECK SUPPORTS FLUSH
AGAINST THE CENTER POSTS, ON TOP OF THE BLOCK
SUPPORTS. MAKE SURE THE OFFSET HOLES ON ONE
CENTER DECK SUPPORT ARE UP AND THE OTHER OFFSET
HOLES ARE DOWN. FASTEN THE CENTER DECK SUPPORTS
TO THE CENTER POSTS AND TIRE SWING BEAM WITH FOUR
3 ½” LAG BOLTS WITH 3/8” WASHERS PER SIDE.

STEP #9:
1. PLACE THE 4 X 4 X 25” BLOCKS FLUSH ON TOP OF THE
BLOCK SUPPORTS, BETWEEN THE CENTER AND END DECK
SUPPORTS. FASTEN THE BLOCKS TO THE BLOCK SUPPORTS
WITH TWO 5” LAG BOLTS WITH 3/8” WASHERS PER BLOCK.