PLAYSTAR FACTORY BUILT ALL PRO PS 73831 Installation and operating manual

Call Toll Free 1-888-752-9782
Customer Service: Monday - Friday, 8:00 A.M. to 5:00 P.M. C.S.T.
We’re Here To Help!
Safety Guide & Assembly Instructions
®®
PS 73831 PS 73832
PS 73833 PS 73834

2
Twice a month during play season: Date: _________
Tighten all hardware.
Check all protective coverings on bolts, pipes, edges,
and corners. Replace if they are loose, cracked, or missing.
Rake and check depth of loose fill protective
surfacing materials to prevent compaction and to
maintain appropriate depth. Replace as necessary.
Once a month during play season: Date: _________
Lubricate all metallic moving parts per
manufacturer’s instructions.
Check all moving parts including swing seats, ropes,
cables, and chains for wear, rust, or other
deterioration. Replace as needed.
At the end of each play season or when the
temperature drops below 0º F: Date: _________
Remove plastic swing seats and other items as specified
by the manufacturer and take indoors or do not use.
Rake and check depth of loose fill protective
surfacing materials to prevent compaction and to
maintain appropriate depth. Replace as necessary.
At the beginning of play season: Date: ___________
Tighten all hardware.
Lubricate all metallic moving parts per
manufacturer’s instructions.
Check all protective coverings on bolts, pipes, edges,
and corners. Replace if they are loose, cracked, or missing.
Check all moving parts including swing seats, ropes,
cables, and chains for wear, rust, or other
deterioration. Replace as needed.
Check metal parts for rust. If found, sand and repaint
using a non lead-based paint meeting the
requirements of 16 CRF 1303.
Check all wood members for deterioration and
splinters. Sand down splinters and replace
deteriorating wood members.
Reinstall any plastic parts, such as swing seats or
any other items that were removed for the cold season.
Rake and check depth of loose fill protective
surfacing materials to prevent compaction and to
maintain appropriate depth. Replace as necessary.
INSTALLATION:
1. Follow the instructions provided, do not
alter its design in any way.
2. Place the equipment on level ground,
not less than 6' (1.8m) from any structure
or obstruction such as a fence, garage,
house, overhanging branches, laundry
lines or electrical wires. If the area
where you will be installing your play-
set is not level, you must make it level.
3. Playsets must be anchored to the
ground. Follow the anchoring instruc-
tions provided with your building kit. If
soil conditions permit anchors to be
pulled out easily, such as in sandy soil
conditions, cementing is required.
4. Tighten all bolts securely to the intended
member then cut off all protruding
threaded ends of bolts with a hack saw
flush to the end of the nut and
remove sharp edges with a metal file.
WARNING: Children must not use the
playset until properly installed and proper
shock-absorbing surfacing material is in place.
OPERATION: Observing and
following statements and warnings
reduces the likelihood of serious or fatal
injury.
1. On-site adult supervision is recommended for
children of all ages.
2. Only one child, for each single planned
seat or single planned activity should
be allowed on this set at one time, with
a maximum weight of 105 pounds for
each child.
WARNING: You must teach children the
following:
A. Not to walk close to, in front of, behind,
or between moving items.
B. Not to twist swing chains or ropes or loop
them over the top support bar since this may
reduce the strength of the chain or rope.
C. Avoid swinging empty seats.
D. To Sit in the center of the swings with
their full weight on the seats.
E. Not to use the equipment in a manner
other than intended.
F.
Not to get off equipment while it is in motion.
G. Not to climb when equipment is wet.
H. Not to attach items to the playground
equipment that are not specifically
designed for use with the equipment
such as, but not limited to, jump
ropes, clothesline, pet leashes, cables
and chain as they may cause a
strangulation hazard.
I. Remove bike or other sports helmet
before playing on the playground
equipment.
3. Verify that suspended climbing ropes
are secured at both ends and that they
cannot be looped back on themselves.
4. Never add extra length to chain or rope.
The chains or ropes provided are the
maximum length designed for the swinging
element(s).
5. Dress children appropriately and do not
allow them to wear inappropriate items,
such as but not limited to, loose fitting
clothing, hood and neck draw strings,
scarves, cord-connected items, capes,
and ponchos. These items can cause
death by strangulation. Provide well-
fitting and full enclosure footwear.
Examples of inappropriate footwear
are clogs, flip flops, and sandals.
6. Verify that all suspended swinging
components have at least 8" clear-
ance between the lowest point of
component and top of shock-absorbing
surfacing material.
WARNING: Lawn swings are designed for use
by children two years of age and older. Use
by children under the age of two can result in
entrapment between the seat and backrest.
NEVER place children in a rearward facing
position or with legs between the seat and
backrest because the child’s body may pass
through the opening causing entrapment of the
child’s head.
DISPOSAL:
When the playset is to be retired from service,
disassemble and dispose of in such a way that
no unreasonable hazards will exist. Follow
your local disposal requirements.
SAFETY
ANNUAL MAINTENANCE CHECKLIST
(Copy this section as needed and maintain for your records or visit www.playstarinc.com/maintenance)
Owner shall be responsible for maintaining the legibility of any warning labels.
If any of these conditions exist, call 1-888-752-9782 for ordering information.
Clean plastic components with warm water and a mild detergent such as dish soap.
2H 2H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
The Consumer Product Safety Commission provides the
following consumer information for your Home Playground Equipment
• This product is intended for single-family residential
use only, by children ages two to ten and a maxi-
mum weight of 105 pounds. Any recommendation
over 10 years of age or 105 pounds exceeds the
upper limits specified in the American Society for
Testing and Materials (ASTM) Home Playground
Safety Standard. In order for PlayStar to comply
with the ASTM Standard, we cannot recommend
anyone above these limits.
• It is a misuse of this product when installed or used
in places of public assembly such as schools or parks.
Select Protective Surfacing
Poured-In-Place Surfaces or
Pre-Manufactured Rubber Tiles
Placement
NOTE: Do not install home playground
equipment over concrete, asphalt,
packed earth, grass, carpet or any
other hard surface. A fall onto a hard
surface can result in serious injury
or death to the equipment user.
Grass and dirt are not considered
protective surfacing because wear
and environmental factors can reduce
their shock absorbing effectiveness.
Carpeting and thin mats are generally
not adequate protective surfacing.
Ground level equipment -- such as a
sandbox, activity wall, playhouse or
other equipment that has no elevated
play surface -- does not need any
protective surfacing.
• Maintain a minimum depth of 9 inches of
loose-fill materials such as wood mulch /
chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for
PlayStar Playsets require fall-height
protection from eight feet.
equipment up to 8 feet high. NOTE: An
initial fill level of 12 inches will compress
to about a 9-inch depth of surfacing over
time. The surfacing will also compact,
displace, and settle, and should be
periodically refilled to maintain at least a
9-inch depth.
• Use containment, such as digging out
around the perimeter and/or lining the
perimeter with landscape edging. Don’t
forget to account for water drainage.
• Check and maintain the depth of the
loose-fill surfacing material. To maintain
the right amount of loose-fill materials,
mark the correct level on play equipment
support posts. That way you can easily
see when to replenish and/or redistribute
the surfacing.
• Do not install loose fill surfacing over
hard surfaces such as concrete or asphalt.
This height should be equal to or greater
than the fall height - vertical distance
between a designated play surface
(elevated surface for standing, sitting, or
climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently
for wear.
• Follow the instructions provided, do not alter its
design in any way.
• Construction requires at least two adults capable of
heavy lifting.
• Thoroughly read all safety instructions before
beginning.
• Children must remain clear of construction site until
this product is properly installed and ready for use.
• Save these instructions in the event the
manufacturer has to be contacted.
Proper placement and maintenance of
protective surfacing is essential.
Be sure to;
• Extend surfacing at least 6 feet from the
equipment in all directions.
• For to-fro swings, extend protective
surfacing in front of and behind the
swing to a distance equal to twice the
height of the top bar from which the
swing is suspended.
SAFETY
Loose-Fill Materials
You may be interested in using surfacing
other than loose-fill materials -- like rubber
tiles or poured-in-place surfaces.
• Installations of these surfaces generally
require a professional and are not
"do-it-yourself" projects.
• Review surface specifications before
purchasing this type of surfacing. Ask the
installer/manufacturer for a report showing
that the product has been tested to the
following safety standard: ASTM F1292
Standard Specification for Impact
Attenuation of Surfacing Materials within
the Use Zone of Playground Equipment.
This report should show the specific
height for which the surface is intended
to protect against serious head injury.
One of the most important things you can
do to reduce the likelihood of serious
head injuries is to install shock-absorbing
protective surfacing under and around your
play equipment. The protective surfacing
should be applied to a depth that is suitable
for the equipment height in accordance with
ASTM F1292. There are different types of
surfacing to choose from; whichever
product you select, follow these guidelines:
20181204

3
Twice a month during play season: Date: _________
Tighten all hardware.
Check all protective coverings on bolts, pipes, edges,
and corners. Replace if they are loose, cracked, or missing.
Rake and check depth of loose fill protective
surfacing materials to prevent compaction and to
maintain appropriate depth. Replace as necessary.
Once a month during play season: Date: _________
Lubricate all metallic moving parts per
manufacturer’s instructions.
Check all moving parts including swing seats, ropes,
cables, and chains for wear, rust, or other
deterioration. Replace as needed.
At the end of each play season or when the
temperature drops below 0º F: Date: _________
Remove plastic swing seats and other items as specified
by the manufacturer and take indoors or do not use.
Rake and check depth of loose fill protective
surfacing materials to prevent compaction and to
maintain appropriate depth. Replace as necessary.
At the beginning of play season: Date: ___________
Tighten all hardware.
Lubricate all metallic moving parts per
manufacturer’s instructions.
Check all protective coverings on bolts, pipes, edges,
and corners. Replace if they are loose, cracked, or missing.
Check all moving parts including swing seats, ropes,
cables, and chains for wear, rust, or other
deterioration. Replace as needed.
Check metal parts for rust. If found, sand and repaint
using a non lead-based paint meeting the
requirements of 16 CRF 1303.
Check all wood members for deterioration and
splinters. Sand down splinters and replace
deteriorating wood members.
Reinstall any plastic parts, such as swing seats or
any other items that were removed for the cold season.
Rake and check depth of loose fill protective
surfacing materials to prevent compaction and to
maintain appropriate depth. Replace as necessary.
INSTALLATION:
1. Follow the instructions provided, do not
alter its design in any way.
2. Place the equipment on level ground,
not less than 6' (1.8m) from any structure
or obstruction such as a fence, garage,
house, overhanging branches, laundry
lines or electrical wires. If the area
where you will be installing your play-
set is not level, you must make it level.
3. Playsets must be anchored to the
ground. Follow the anchoring instruc-
tions provided with your building kit. If
soil conditions permit anchors to be
pulled out easily, such as in sandy soil
conditions, cementing is required.
4. Tighten all bolts securely to the intended
member then cut off all protruding
threaded ends of bolts with a hack saw
flush to the end of the nut and
remove sharp edges with a metal file.
WARNING: Children must not use the
playset until properly installed and proper
shock-absorbing surfacing material is in place.
OPERATION: Observing and
following statements and warnings
reduces the likelihood of serious or fatal
injury.
1. On-site adult supervision is recommended for
children of all ages.
2. Only one child, for each single planned
seat or single planned activity should
be allowed on this set at one time, with
a maximum weight of 105 pounds for
each child.
WARNING: You must teach children the
following:
A. Not to walk close to, in front of, behind,
or between moving items.
B. Not to twist swing chains or ropes or loop
them over the top support bar since this may
reduce the strength of the chain or rope.
C. Avoid swinging empty seats.
D. To Sit in the center of the swings with
their full weight on the seats.
E. Not to use the equipment in a manner
other than intended.
F. Not to get off equipment while it is in motion.
G. Not to climb when equipment is wet.
H. Not to attach items to the playground
equipment that are not specifically
designed for use with the equipment
such as, but not limited to, jump
ropes, clothesline, pet leashes, cables
and chain as they may cause a
strangulation hazard.
I. Remove bike or other sports helmet
before playing on the playground
equipment.
3. Verify that suspended climbing ropes
are secured at both ends and that they
cannot be looped back on themselves.
4. Never add extra length to chain or rope.
The chains or ropes provided are the
maximum length designed for the swinging
element(s).
5. Dress children appropriately and do not
allow them to wear inappropriate items,
such as but not limited to, loose fitting
clothing, hood and neck draw strings,
scarves, cord-connected items, capes,
and ponchos. These items can cause
death by strangulation. Provide well-
fitting and full enclosure footwear.
Examples of inappropriate footwear
are clogs, flip flops, and sandals.
6. Verify that all suspended swinging
components have at least 8" clear-
ance between the lowest point of
component and top of shock-absorbing
surfacing material.
WARNING: Lawn swings are designed for use
by children two years of age and older. Use
by children under the age of two can result in
entrapment between the seat and backrest.
NEVER place children in a rearward facing
position or with legs between the seat and
backrest because the child’s body may pass
through the opening causing entrapment of the
child’s head.
DISPOSAL:
When the playset is to be retired from service,
disassemble and dispose of in such a way that
no unreasonable hazards will exist. Follow
your local disposal requirements.
SAFETY
ANNUAL MAINTENANCE CHECKLIST
(Copy this section as needed and maintain for your records or visit www.playstarinc.com/maintenance)
Owner shall be responsible for maintaining the legibility of any warning labels.
If any of these conditions exist, call 1-888-752-9782 for ordering information.
Clean plastic components with warm water and a mild detergent such as dish soap.
2H 2H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
The Consumer Product Safety Commission provides the
following consumer information for your Home Playground Equipment
• This product is intended for single-family residential
use only, by children ages two to ten and a maxi-
mum weight of 105 pounds. Any recommendation
over 10 years of age or 105 pounds exceeds the
upper limits specified in the American Society for
Testing and Materials (ASTM) Home Playground
Safety Standard. In order for PlayStar to comply
with the ASTM Standard, we cannot recommend
anyone above these limits.
• It is a misuse of this product when installed or used
in places of public assembly such as schools or parks.
Select Protective Surfacing
Poured-In-Place Surfaces or
Pre-Manufactured Rubber Tiles
Placement
NOTE: Do not install home playground
equipment over concrete, asphalt,
packed earth, grass, carpet or any
other hard surface. A fall onto a hard
surface can result in serious injury
or death to the equipment user.
Grass and dirt are not considered
protective surfacing because wear
and environmental factors can reduce
their shock absorbing effectiveness.
Carpeting and thin mats are generally
not adequate protective surfacing.
Ground level equipment -- such as a
sandbox, activity wall, playhouse or
other equipment that has no elevated
play surface -- does not need any
protective surfacing.
• Maintain a minimum depth of 9 inches of
loose-fill materials such as wood mulch /
chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for
PlayStar Playsets require fall-height
protection from eight feet.
equipment up to 8 feet high. NOTE: An
initial fill level of 12 inches will compress
to about a 9-inch depth of surfacing over
time. The surfacing will also compact,
displace, and settle, and should be
periodically refilled to maintain at least a
9-inch depth.
• Use containment, such as digging out
around the perimeter and/or lining the
perimeter with landscape edging. Don’t
forget to account for water drainage.
• Check and maintain the depth of the
loose-fill surfacing material. To maintain
the right amount of loose-fill materials,
mark the correct level on play equipment
support posts. That way you can easily
see when to replenish and/or redistribute
the surfacing.
• Do not install loose fill surfacing over
hard surfaces such as concrete or asphalt.
This height should be equal to or greater
than the fall height - vertical distance
between a designated play surface
(elevated surface for standing, sitting, or
climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently
for wear.
• Follow the instructions provided, do not alter its
design in any way.
• Construction requires at least two adults capable of
heavy lifting.
• Thoroughly read all safety instructions before
beginning.
• Children must remain clear of construction site until
this product is properly installed and ready for use.
• Save these instructions in the event the
manufacturer has to be contacted.
Proper placement and maintenance of
protective surfacing is essential.
Be sure to;
• Extend surfacing at least 6 feet from the
equipment in all directions.
• For to-fro swings, extend protective
surfacing in front of and behind the
swing to a distance equal to twice the
height of the top bar from which the
swing is suspended.
SAFETY
Loose-Fill Materials
You may be interested in using surfacing
other than loose-fill materials -- like rubber
tiles or poured-in-place surfaces.
• Installations of these surfaces generally
require a professional and are not
"do-it-yourself" projects.
• Review surface specifications before
purchasing this type of surfacing. Ask the
installer/manufacturer for a report showing
that the product has been tested to the
following safety standard: ASTM F1292
Standard Specification for Impact
Attenuation of Surfacing Materials within
the Use Zone of Playground Equipment.
This report should show the specific
height for which the surface is intended
to protect against serious head injury.
One of the most important things you can
do to reduce the likelihood of serious
head injuries is to install shock-absorbing
protective surfacing under and around your
play equipment. The protective surfacing
should be applied to a depth that is suitable
for the equipment height in accordance with
ASTM F1292. There are different types of
surfacing to choose from; whichever
product you select, follow these guidelines:
20181204

4
³₈" x 2"
hex bolts
(9)
³₈" x 3¹₂" hex bolts (12)
#8 x 2¹₂" deck screws (41)
#8 x 1¹₂" deck screws (4)
#8 x 1¹₄"
deck screws
(16)
#14 x 1¹₄"
pan head screws
(14)
³₈" lock nuts
(23)
³₈" washers
(53)
³₈" x 1¹₂" lag screw (7)
fence staple (4)
³₈" x 1¹₄"
hex bolt (1)
#8 x 2"
truss head screws
(4)
#8 x 1"
truss head
screws
(4)
#8 x ⁵₈"
truss head
screws
(56)
³⁄₈" x 5" Hex Bolt (1)
HARDWARE INCLUDED (shown actual size)
TOOLS REQUIRED
Level
Square
Pencil
Hammer
Drill
Shovel
Ladder
Hack Saw
Metal File
1/8”, 1/4”, & 3/8” Drill Bits (Included)
Phillips & Slotted Bits (Included)
Socket Wrench
1/2” & 9/16” Sockets
Adjustable Wrench
Screwdriver (regular or phillips)
Tape Measure
Safety Glasses
Sawhorses (optional)

5
Contents:
Front View
Back View
Area Requirements
CONTENTS – Gold Design Option
1 Tower - With:
2 Play Handles
4 Climbing Bars
1 Sand Box Seat
2 Roof Panels (1 w/9 & 1 w/11 Boards)
1 Bridge-Tunnel Assembly With:
2 Play Handles
1 Tunnel (Green)
1 Wood Rock Wall (4 Rocks)
1 Laminated Leg
1 Swing Beam (10’ Left
w/Air Rider Brackets)
1 A-Frame
2 2” X 4” X 50 3/4” boards
1 2” X 4” X 28” board
1 Tube Slide w/Pre-assembled base
1 Air Rider (Assembled)
1 Decorative Kit Box - Includes:
1 Dormer
1 Cupola
1 Flag
1 Flag Pole
1 Sunlight Window
1 Stencil Kit
1 Flower Box
1 Design-a-Plaque
1 Magnetic Chalkboard
1 Decorative Hardware Bag
1 Component Box - Includes:
1 Swing Assembly (Yellow)
2 Gym Ring Assemblies (Yellow)
1 Telescope Assembly
2 Roof Caps
1 Twisted Rope
7 Anchor Augers
1 Sturdy-Frame Brace
2 Corner Brackets
1 2” X 6” X 12” board
1 All Pro Hardware Bag
1 All Pro F-B Instructions

6
Contents: Front View
Back View
Area Requirements
CONTENTS – Silver Design Option
1 Tower - With:
4 Play Handles
4 Climbing Bars
2 Roof Panels (1 w/9 & 1 w/11 Boards)
1 Wood Rock Wall (4 Rocks)
1 Laminated Leg
1 Swing Beam (10’ Left)
1 A-Frame
2 2” X 4” X 50 3/4” boards
1 2” X 4” X 28” board
1 Tube Slide w/Pre-assembled base
1 Component Box - Includes:
1 Swing Assembly (Yellow)
1 Swing Assembly (Rigid)
2 Gym Ring Assemblies (Yellow)
1 Telescope Assembly
2 Roof Caps
1 Twisted Rope
7 Anchor Augers
1 Sturdy-Frame Brace
2 Corner Brackets
1 2” X 6” X 12” board
1 All Pro Hardware Bag
1 All Pro F-B Instructions

7
Contents:
Front View
Back View
Area Requirements
CONTENTS – Bronze Design Option
1 Tower - With:
2 Play Handles
4 Climbing Bars
1 Sand Box Seat
2 Roof Panels (1 w/9 & 1 w/11 Boards)
1 Bridge-Tunnel Assembly With:
2 Play Handles
1 Tunnel (Green)
1 Wood Rock Wall (4 Boards)
1 Laminated Leg
1 Swing Beam (10’ Left)
1 A-Frame
2 2” X 4” X 50 3/4” boards
1 2” X 4” X 28” board
1 Scoop Slide
1 Decorative Kit Box - Includes:
1 Dormer
1 Cupola
1 Flag
1 Flag Pole
1 Sunlight Window
1 Stencil Kit
1 Flower Box
1 Design-a-Plaque
1 Magnetic Chalkboard
1 Decorative Hardware Bag
1 Component Box - Includes:
1 Swing Assembly (Yellow)
1 Swing Assembly (Rigid)
2 Gym Ring Assemblies (Yellow)
1 Telescope Assembly
2 Roof Caps
1 Twisted Rope
7 Anchor Augers
1 Surdy-Frame Brace
2 Corner Brackets
1 2” X 6” X 12” board
1 All Pro Hardware Bag
1 All Pro F-B Instructions

8
Contents: Front View
Back View
Area Requirements
CONTENTS – Starter Design Option
1 Tower - With:
4 Play Handles
4 Climbing Bars
2 Roof Panels (1 w/9 & 1 w/11 Boards)
1 Wood Rock Wall (4 Rocks)
1 Laminated Leg
1 Swing Beam (10’ Left)
1 A-Frame
2 2” X 4” X 50 3/4” boards
1 2” X 4” X 28” board
1 Scoop Slide
1 Component Box - Includes:
1 Swing Assembly (Yellow)
1 Swing Assembly (Rigid)
2 Gym Ring Assemblies (Yellow)
1 Telescope Assembly
2 Roof Caps
1 Twisted Rope
7 Anchor Augers
1 Sturdy-Frame Brace
2 Corner Brackets
1 2” X 6” X 12” board
1 All Pro Hardware Bag
1 All Pro F-B Instructions

9
TOWER ASSEMBLY
Items for STEP 1:
(1) Tower Assembly
(1) 2” x 4” x 50C|v” board
(4) #8 x 2¹⁄₂” deck screws
Position Tower in its desired location.
Attach one 2” x 4” x 50C|v” board
as shown. Secure with
#8 x 2¹⁄₂” deck screws.
2" x 4" x 50³⁄₄"
Flush
6”
overhang
each side
(Tube Slide
opening shown)

10
2" x 4" x 50³⁄₄"
Items for STEP 3:
(4) #8 x 1¹|v” deck screws
(2) C|₈”�x 2” hex bolts
(4) C|₈” washers
(2) C|₈” lock nuts
2" x 4" x 50³⁄₄"
Use the bracket as a drill guide
and drill ¹|₈” holes 1” deep into the
2” x 4” x 50C⁄v” board. Attach with
#8 x 1¹|v” deck screws.
Use bracket as a drill guide and
drill ³|₈” holes completely through
the 2” x 4” x 50C⁄v” boards. Secure
with ³|₈” x 2” hex bolts, ³|₈” washers
and ³|₈” lock nuts.
Items for STEP 2:
(1) 2” x 4” x 50C|v” board
(12) #8 x 2¹⁄₂” deck screws
Attach one 2” x 4” x 50C⁄v” board as shown. Secure with
eight #8 x 2¹⁄₂” deck screws from the inside and four from
the outside as shown.
2" x 4" x 50³⁄₄"
Flush
6"
overhang
each side
2" x 4" x 50³⁄₄"
2" x 4" x 50³⁄₄"
Flush
6"
overhang
each side
2" x 4" x 50³⁄₄"
Outside View
Inside View
(Tube Slide
opening shown)
(Tube Slide
opening shown)

11
Items for STEP 4:
(1) Swing Beam
(1) A-frame Assembly
(1) Sturdy-Frame Brace
(5) C|₈” x 3¹|₂” hex bolts
(10) C|₈” washers
(5) C|₈” lock nuts
Lay swing beam on saw horses as shown. (Fig. 1)
Position the A-frame assembly so that the top post is above
the top bracket and the bottom post is below the bottom
bracket. Line up the holes in the brackets with the holes in
the posts and secure with C|₈” x 3¹|₂” hex bolts, C|₈” washers
and C|₈” lock nuts. (Fig. 2)
Install the Sturdy-Frame Brace as shown and secure with
C|₈” x 3¹|₂” hex bolt, C⁄₈” washer and lock nut. (Fig. 2)
Fig. 1
Fig. 2

12
Step 4 Cont.:
Make sure brace is square to beam. Using the
brace as a template, drill a C⁄₈” hole completely
through beam. (Fig. 3)
Secure the Sturdy-Frame Brace to the beam with
a C⁄₈” x 3½” hex bolt, C|₈” washer and C|₈” lock nut.
Locate the hole on the 2” x 4” board of tower
assembly where the Swing Station Assembly
will be attached.
Position Swing Station Assembly against tower
and secure with one C|₈” x 5” hex bolt, washers
and lock nut as shown.
Items for STEP 5:
(1) C|₈” x 5” hex bolt
(2) C|₈” washers
(1) C|₈” lock nut
Fig. 3
Drill

13
Position the laminated leg on the single bracket so that the holes of the
bracket line up with the holes in the single post as shown.
Secure with C|₈” x 3¹|₂” hex bolts, C|₈” washers and C|₈” lock nuts as shown.
Items for STEP 6:
(1) Laminated Leg
(2) C|₈” x 3¹|₂” hex bolts
(4) C|₈” washers
(2) C|₈” lock nuts

14
Items for STEP 7:
(1) 2” x 4” x 28” board
(2) Corner brackets
(4) #8 x 2¹|₂” deck screws
(8) #8 x 1¹|v” deck screws
(1) C|₈” x 3¹|₂” hex bolt
(3) C|₈” x 2” hex bolts
(8) C|₈” washers
(4) C|₈” lock nuts
Position 2” x 4” x 28” board approximately 34C|v” up from bottom of
tower flush with the tower and swing beam posts as shown. Attach with
#8 x 2¹|₂” deck screws.
Attach corner brackets. Position brackets so that the short sides are
against the 2” x 4” x 28” board.
Use the bracket as a drill guide and drill ¹|₈” holes 1” deep into the
board. Attach with #8 x 1¹|v” deck screws.
Again use the bracket as a drill guide and drill ³|₈” holes completely
through the boards. Secure with ³|₈” hex bolts, ³|₈” washers and
³|₈” lock nuts.
NOTE: If you are bolting through one
board use a ³|₈” x 2” hex bolt.
If you are bolting through two
boards, use a ³|₈” x 3¹|₂” hex bolt.
34³⁄₄"
2" x 4" x 28"
Flush
Back View

15
GOLD & BRONZE ONLY
Items for STEP 1:
(1) Rock Wall Assembly
(1) Bridge-Tunnel assembly
(4) C⁄₈” x 2” hex bolts
(8) C⁄₈” washers
(4) C⁄₈” lock nuts
Position Rock Wall and Bridge-Tunnel as
shown, making sure the C⁄₈” holes line up
with the pre-drilled holes.
Secure bridge brackets with C⁄₈” x 2” hex
bolts, C⁄₈” washers and C⁄₈” lock nuts.

16
Items for STEP 2:
(1) Bridge-Tunnel Assembly
(4) #8 x 2¹⁄₂” deck screws
Attach Bridge-Tunnel assem-
bly to tower as shown. Make
sure its decking frame firmly
rests against the tower deck-
ing frame without any gap in
between. Also, make sure the
top surfaces of both decks are
flush as shown. Secure with
#8 x 2¹⁄₂” deck screws through
the pre-drilled holes located
under decking.
Detail from below
#8 x 2¹⁄₂”
deck screws
Flush
both decks

17
Position the tunnel into the bridge opening as shown.
Make sure the tunnel is fully inserted and the flanges are firmly
resting against the lumber and the ends are flush with the sides
of the lumber as shown.
Find the center of the arch and line it up with the screw hole at
the top of the tunnel.
Starting with the screw hole located at the top, drill a 1/8” hole,
1/8” deep. Secure with a #8 x B|₈” truss head screw.
Continue with the next adjacent screw hole working your way
all the way down, making sure the flanges are firmly resting
against the lumber without any bulging.
Repeat for the other end
of the tunnel.
Secure both sides
of the tunnel to
2” x 4” x 58¹⁄₂” boards
with #8 x B|₈” truss
head screws. Make
sure the flanges are
firmly resting against
the lumber without
any bulging.
Items for STEP 3:
(1) Tunnel
(36) #8 x B|₈” truss head screws
Center
Flush
2" x 4" x 58¹⁄₂"
Start with
this hole

18
1" x 4" x 21⁷⁄₁₆" (12)
Climbing
Rope Holes
Items for STEP 1:
(1) Rock Wall Assembly
(4) #8 x 1¹|v” deck screws
(2) C|₈” x 2” hex bolts
(4) C|₈” washers
(2) C|₈” lock nuts
Attach Rock Wall to corner brackets. Bottom corners of Rock Wall must
rest on the ground and the top edge of the Rock Wall must be tight
against 2” x 4” x 58¹⁄₂” as shown.
Use the brackets as a drill guide and drill ¹⁄₈” holes 1” deep into the
boards. Attach with #8 x 1¹⁄v” deck screws.
Again use the brackets as a drill guide and drill
C⁄₈” holes completely through the board. Secure with
C⁄₈” x 2” hex bolts, C⁄₈” washers and C⁄₈” lock nuts.
Install rope per instructions on Page 35.
SILVER & STARTER ONLY
2” x 4” x 58¹|₂”

19
This Page Left Blank Intentionally.

20
Drill this hole for roof
boards C⁄v” or thinner
TAPE HERE TO ROOF