PLAYSTAR Bronco Rider User manual

Assembly Instructions
PS 7956
®
Call Toll Free 1-888-752-9782
Customer Service: Monday - Friday, 8:00 A.M. to 5:00 .M. C.S.T.
We’re Here To Help!
Play Action ®
Important!
Intended for residential use by children ages 2 to 10, only on properly
installed layStar playsets. Before use refer to complete safety guidelines
in your original playset, at www.playstarinc.com, or at 1-888-752-9782.
Warning!
No more than two children should be allowed on this accessory at one time,
with a maximum weight of 105 pounds for each child.

(1) Bronco Rider
(4) Welded-Link Chains
(1) Swing Hanger
Assembly System
(1) Bracket System
Weather-Resistant
Hardware
Complete Illustrated
Instructions
CONTENTS TOOLS REQUIRED
HARDWARE INCLUDED (shown act al size)
Socket Wrench and
Extension
⁹⁄₁₆" Socket
⁹⁄₁₆" or Adjustable
Wrench
Tape Measure
Safety Glasses
Drill
Bronco Rider Kit
Contains:
SWING HANGER ASSEMBLY
1. osition one bracket on the beam, at least 10" away from the
closest point of all other rides or stationary objects. Make sure
the alignment tab is flush with the bottom of the beam as shown.
Using the bracket as a guide, drill two ³⁄₈" holes straight through
the beam. Install two ³⁄₈" x 4" hex head bolts with washers through
the bracket and beam to hold the bracket in place. (Fi . 1)
2. Slide the second bracket in place over the bolts. Install one
washer and lock nut on each bolt and tighten nuts (you
will need a socket extension for this step). (Fi . 1)
Fi . 1
Beam
Square
Hammer
³⁄₈" Drill Bit
Hack Saw
Metal File
encil
Ladder
Alignment Tabs
³|₈" x 7" hex bolt (2)
³|₈" x 4" hex bolt (4)
³|₈" x 1¹|₄" hex bolt (4)
³|₈" Lock Nut (10) ³|₈" Washer (12)

1. Connect saddle to handles using ³⁄₈" x 7" hex bolts, two ³⁄₈" washers, and ³⁄₈" lock nuts
as shown. Tighten securely, but do not over tighten, with a ⁹⁄₁₆" wrench and socket wrench.
Repeat for other end. (Fi . 1)
2. Connect chain onto Bronco Rider handle using quick-link connectors provided. Tighten with
adjustable wrench. (Fi . 1)
Caution: Failure to tighten
quick-links securely
could result in injury.
3. Lift Bronco Rider into position
and hook chains onto the swing
hangers.
Fi . 1
4. Mark over 16" from center of bolts. Repeat Step 1
through Step 3 for the second assembly. (Fi . 3)
Fi . 2
Fi . 3
BRONCO RIDER ASSEMBLY
3. Install swing hangers to bracket using ³⁄₈" x 1¹⁄₄" hex
head bolts and lock nuts as shown. Tighten with ⁹⁄₁₆"
wrench and socket wrench. (Fi . 2)
Caution: At least 10" minimum spacing is required from the closest point of all
other rides or stationary objects.
Caution: Cut off all protruding threaded ends of bolts with a hack saw flush to the
end of the nut and remo e sharp edges with a metal file.
16"
Caution: Do not o er tighten.

Thank Yo for choosing PlayStar. Beca se it is
o r intention to make this a positive family experience,
we have taken great care in preparing this prod ct.
Sho ld yo have any q estions, or if we can assist yo
in any way, please call o r friendly C stomer Service
Department for immediate action.
Ask for Customer Service.
We Will Gladly Help!
rinted in U.S.A.LT 6448 R5
© 2005, 2004 layStar, Inc. Reproduction of this document in part or whole is prohibited without the permission of layStar, Inc.
rotected by one or more of the following United States or Foreign atents: US D422,332; US D424,649; US 6,068,557; US 7,186,183; CA 2,490,923
layStar, Incorporated, Janesville, WI 53547
Please call us Toll Free at 1-888-PLAYSTAR
(752-9782)
Monday through Friday, 8:00 A.M. to 5:00 .M. C.S.T.
Do not return to the store.