Porter&Charles COMBI9-6 User manual

COMBI9-6
•24” (60cm) 2-in-1 Combination Washer/Dryer
2016 SPECIFICATION SHEET

Specifications are subject to change without notice
V1.0
COMBI9-6
24” (60cm) 2-in-1 Combination Washer/Dryer
Our unique washer and dryer combo is designed to give you more free time. Load the machine, set to wash+dry and
come back to clean, dry clothes.
•24” (60cm) 2-in-1 combination
washer/dryer
•Wash and dry your clothes in one cycle or
select one of the many wash only programs
and dry only programs
•9kg washing capacity
•6kg drying capacity
•Condensation dryer, automatically drained
•Quiet operation
•Wash –58 dBa
•Spin –77 dBa
•Dry –64 dBa
•Universal motor with DC drive
•Cold water intake –machine heats water to
90◦C
•60 litre drum volume
•Full graphic LCD display with touch buttons
•3D load sensor
•1400 RPM spin speed
•Active Jet® washing system
WASHER FEATURES
D: 24” • W: 235/8” • H: 331/2”
D: 610 mm • W: 600 mm • H: 850 mm
WASHER DIMENSIONS
•208/240 Volt, 60Hz receptacle –(NEMA 6-15R)
•15 AMP Breaker Required
ELECTRICAL REQUIREMENTS

Specifications are subject to change without notice
V1.0
SPECIFICATIONS
COMBI9-6
D: 24” • W: 235/8” • H: 331/2”
D: 610 mm • W: 600 mm • H: 850 mm
WASHER DIMENSIONS
D: 24” • W: 24” • H: min. 341/2”
D: 610 mm • W: 610 mm • H: 876 mm
CUT-OUT DIMENSIONS
* No Exterior Ventilation required
* Cold water hook-up via 4ft. long hose located at back top
Installing under counter / stand alone

Specifications are subject to change without notice
V1.0
SPECIFICATIONS –CABINET INSTALLATION
COMBI9-6
•D: 261/2” • W: min. 28” (Outside Cabinet Dimension) • H: min. 35”
•D: 673 mm • W: 711 mm • H: 889 mm
CUT-OUT DIMENSIONS
•If housed in a cabinet air vents ARE REQUIRED
•Air vent must be 200 cm2
•The cabinet space in which the Combi9-6 is installed MUST BE
•REINFORCED to withstand the weight and vibrations of the unit
CUT-OUT DIMENSIONS

Specifications are subject to change without notice
V1.0
SPECIFICATIONS –HOSES & CONNECTIONS
COMBI9-6
•Install the laundry appliance so as to allow ease of access to the electrical and connections through the adjacent
cabinet. These connections must never be behind the laundry appliance.
•The inlet and drain hoses can be positioned in either direction, make sure that they are not bent, crushed or too
tight. Tighten the ring nut after pointing the hoses in the required direction.
Hoses & Connections
•Installing the laundry appliance in a narrow space
may bend or crush the connections (hoses, power
cord). Take great care in order to reduce the
possibility of damaging the connections when
installing or removing the appliance.
•A through hole with a diameter of at least 10 cm (4”)
is required to pass the hoses and power cord . Make
sure there are no rough edges that could damage the
power cord or hoses. If the laundry appliance is
installed in a metal unit protect the edge of the
through hole for the hoses and power cord with a
gasket. Do not use extension cords when making the
electrical connection.
Hoses and Connections - Installing the appliance in a narrow space