Portwell WEBS-5491 User manual

WEBS-5491
Fan-less Embedded System
User's Manual
Version 1.0
Copyright © Portwell, Inc., 2015. All rights reserved.
All other brand na es are registered trade arks of their respective owners.

Preface
Table of Contents
How to Use This Manual
Chapter 1 System Overview.......................................................................................................1-1
1.1 Introduction ....................................................................................................... 1-1
1.2 Check List ........................................................................................................... 1-1
1.3 Product Specification ........................................................................................ 1-3
1.4 Mechanical Di ension ..................................................................................... 1-4
Chapter 2 System Installation....................................................................................................2-1
2.1 E bedded Board H/W Ju per Setting Introduction ................................. 2-1
2.2 Selectable I/O Kit Installation ......................................................................... 2-5
2.3 Me ory Installation ......................................................................................... 2-6
2.4 HDD Installation ............................................................................................... 2-7
2.5 CF and SD card Installation ............................................................................. 2-7
2.6 Getting Started ................................................................................................... 2-8
2.7 I/O Interfaces .................................................................................................... 2-8
2.7.1 Front View ................................................................................................. 2-8
2.7.2 Rear View .................................................................................................. 2-9
Chapter 3 BIOS Setup Information............................................................................................3-1
3.1 Entering Setup—Launch Syste Setup ......................................................... 3-1
3.2 Main .................................................................................................................... 3-2
3.3 Configuration .................................................................................................... 3-3
3.4 Security ............................................................................................................. 3-20
3.5 Boot ................................................................................................................... 3-21
3.6 Save and Exit ................................................................................................... 3-23
Chapter 4 Important Instructions ..............................................................................................4-1
4.1 Note on the Warranty ....................................................................................... 4-1
4.2 Exclusion of Accident Liability Obligation ................................................... 4-1
4.3 Liability Li itations / Exe ption fro the Warranty Obligation............ 4-1
4.4 Declaration of Confor ity ............................................................................... 4-1
Chapter 5 Frequent Asked Questions.......................................................................................5-1

Preface
How to Use This Manual
The anual describes how to configure your WEBS-5491 e bedded syste to eet
various operating require ents. It is divided into five chapters, with each chapter
addressing a basic concept and operation of Fan-less E bedded Syste .
Chapter 1: System Overview. Present what ay have in the box and give an
overview of the product specifications and basic syste architecture for this fan-less
e bedded syste .
Chapter 2: System Installation. Show the definitions and locations of all the
interfaces and describe a proper installation guide so that can easily configure the
syste .
Chapter 3: BIOS Setup Information. Specify the eaning of each setup para eters,
how to get advanced BIOS perfor ance and update new BIOS. In addition, POST
checkpoint list will give users so e guidelines of trouble-shooting.
Chapter 4: Important Instructions. Indicate so e instructions which ust be
carefully followed when the fan-less e bedded syste is used.
Chapter 5: Frequent Asked Questions. Provide the answers for the ost frequently
asked questions.
The content of this anual is subject to change without prior notice. These changes
will be incorporated in new editions of the docu ent. The vendor ay ake
supple ent or change in the products described in this docu ent at any ti e.
Revision History
Revision
Date Details of Change(s)
V1.0 2015/11/11
Initial Release

System Overview
WEBS-5491 Embedded System User’s Manual 1-1
Chapter 1
System Overview
1.1 Introduction
Portwell Inc., a world-leading innovator in the Industrial PC (IPC) arket and a
Pre ier Me ber of the Intel® Internet of Things (IoT) Solutions Alliance, announced
WEBS-5491, a fan-less e bedded syste . Builds on Intel® Baytrail SoC and takes
advantages of Intel® Ato ™ E3845(10 W Max TDP, 2M Cache, 1.91 GHz) processor
technologies, especially its co pact design plus low power consu ption.
The 4th generation Intel Ato Bay Trail-I series provides extended te perature
fro -40 to 110 degrees, high I/O connectivity, integrated e ory controller, error
correcting code (ECC), virtualization, and built-in security capabilities within 10W
ther al design power (TDP). A ong the , E3845 SoC processor is designed for
applications including highly efficient and dedicated i age signal processing with
secure content delivery.
Portwell’s WEBS-5491 is designed to be power-opti ized and value-opti ized.
Instead of adopting a obile CPU like a traditional e bedded syste , WEBS-5491
utilizes the newest Intel® Ato ™ platfor Intel® Ato ™ E3845, and Intel® Baytrail
SoC chipset, which is ore econo ical co pared to its obile counterpart and
provides great efficacy as well as ultra low power consu ption; this akes
WEBS-5491 not only co petitive but outstanding in the arket. This feature allows
WEBS-5491 e bedded syste to be used extensively in harsh environ ents such as
the operating te perature fro -30 to 70 ℃ degrees. The syste includes all required
interfaces for industrial application: 1 x DVI-I port, 2 x Gigabit Ethernet port, 3 x USB
1.1/2.0, 1 x USB 3.0, 2 x RS-232/422/485 port, 1 x 2.5" SATA HDD, 1x CF and 1 x SD
socket for storage capacity. Two SMA Antenna holes provide optional wireless
solution via half size Mini-PCIe odule.
To fulfill different application needs and to secure the syste fro power input
change, the syste accepts DC 12~24V wide range power input with 3-pin ter inal
block connector for various operating environ ent. The WEBS-5491 e bedded
syste offers wall ounting DIN Rail ounting. It supports any ainstrea
operating syste s, such as Windows 8.1, Windows 7 and Linux.
1.2 Check List
The WEBS-5491 E bedded syste package covers the following ite s:
Essential
One WEBS-5491 Fan-less E bedded syste

System Overview
WEBS-5491 Embedded System User’s Manual 1-2
Screws for HDD installation
M3X4L Screw 4 pieces
Driver CD
3-pin Ter inal Block Connector (Fe ale)
Wall ount kit (W/ 6*screws)
Optional
60W Power Adapter with Power Cord (EU/US type) and Switch Cable
60W Power Adapter
Power Cord (US type)
Power Cord (EU type)
Power Switch Cab e (from DC Jack to 3-pin TBC)
Selectable I/O Kit
2x RS-232/422/485, 1x RS-232
(Expansion: Option 1)
1x RS-232/422/485, 2x USB ports and 1x Line-out
(Expansion: Option 2)
DVI to VGA cable
DIN Rail kit (W/ 7*screws)

System Overview
WEBS-5491 Embedded System User’s Manual 1-3
If any of these ite s is da aged or issing, please contact your vendor and keep all
packing aterials for future replace ent and aintenance.
1.3 Product Specification
System
SOC Intel® Atom™ Qual-Core E3845 (1.91 G z)
Memory DDR3L SO-DIMM 1333/1600 M z max up to 8 GB
BIOS AMI
Graphics Intel® Gen7 Graphics
LVDS Single/Dual Channel 24-bit
LAN Chipset Dual Intel® I210IT Gigabit Ethernet (Support Jumbo Frame)
Audio Realtek igh Definition Audio Codec
Watchdog Timer 1~255 levels reset
Storage Device 2.5" SATA DD / SSD, Compact Flash II up to 64 GB, SD card
OS Windows 7 / Windows 8.1 / Linux™
I/O Interface
Series Port 2 x RS-232/422/485 (Expansion : default)
Display 1 x DVI-I
USB 1 x USB 2.0, 1 x USB 3.0, 2 x USB 2.0 (Expansion: default)
Ethernet 2 x Gigabit Ethernet
Others 2 x SMA Antenna hole for WiFi/3G Solution
Expansion 2 x RS-232/422/485, 1 x RS-232 (Expansion: option 1)
1 x Line-out, 1 x RS-232/422/485, 2 x USB 2.0 (Expansion: option 2)
Mechanical
Mounting (mm) VESA Mount 75 x 75 & 100 x 100 ; Panel Mount
Weight (Kg) 2.8kg
Dimension 279(W) x 164(D) x 34( ) mm
Power
Power Supply DC 12 ~ 24V input with 3-pin Terminal Block Connector
Power Adaptor 12V, 5A/60W(Optional)
Environment
OP /Storage Temp -30℃~70 ℃ / -40℃~80℃(20~90% non-condensing)
Vibration 1.0G (CF/SSD/SD) and 0.5G ( DD) , Power on & 2.16G, Packaged; 5~500 z
Shock 15G peak acceleration, 11 ms (Power on condition)
Drop Package with Carton from 96.5 cm (1-Corner, 3-Axis, 6-Face)
Certification CE/FCC Class A

System Overview
WEBS-5491 Embedded System User’s Manual 1-4
1.4 Mechanical Dimension
Front view of the WEBS-5491 syste
Rear view of the WEBS-5491 syste
Side view of the WEBS-5491 syste

System Overview
WEBS-5491 Embedded System User’s Manual 1-5
Top view of the WEBS-5491 syste
Botto view of the WEBS-5491 syste

System Installation
WEBS-5491 Embedded System User’s Manual 2-1
Chapter 2
System Installation
This chapter provides you with instructions to set up your WEBS-5491 e bedded
syste . Definitions and locations of all the interfaces are described so that you can
easily configure your syste .
2.1 Embedded Board H/W Jumper Setting Introduction
WEBS-5491 E bedded syste adopts PEB-99A4 other board. You ay configure
the e bedded syste by setting ju pers of the other board to atch the needs of
your applications. To select any option, cover the ju per cap (SHORT) or re ove
(NC) it fro the ju per pins according to the following instructions.
*Note: NC stands for “Not Connect”.
Component side:

System Installation
WEBS-5491 Embedded System User’s Manual 2-2
Solder side:
Connector and Jumper setting:
Connector
J3 DDR3 SO-DIMM Socket.
J4 Compact F ash connector.
J5 PCI-E X 1 S ot.
J6 Mini-PCI-E S ot.(Ha f size)
J7 SATA Connector with power.
J8 GPIO Connector.(2*5 Pin/2.0mm)
J9 SM- Bus Connector.
J10 Battery Connector.
J11 PCI-E X4 S ot(Right ang e) for Audio and COM Port Signa .
J12 USB Port 0~1 D-Sub Connector. (Up:USB2.0 Down:USB3.0)
J13 RJ45 Connector.
J14 RJ45 Connector.
J15 DVI-I D-sub Connector.
J16 Power Input Connector. (Termina B ocks 3Px1/5.08mm fema e)
J19 SD Card.
J22 USB Port 3 Connector (1*4 Pin Wafer/2mm).
Jumpers
JP1 C ear CMOS.
JP7 GPIO Vo tage se ection.
JP8 Audio out.(From amp ifier)
JP9 LPC Debug Port.
JP10 COM PORT RI and power source adjust pin.

System Installation
WEBS-5491 Embedded System User’s Manual 2-3
JP11 COM PORT RI and power source adjust pin.
JP12 COM PORT RI and power source adjust pin.
JP13 COM PORT RI and power source adjust pin.
SW2 AT/ATX & BIOS recovery Setup.
J8: GPIO Connector (2*5 Pin Header/2 ):
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GPIO0 2 GPIO4
3 GPIO1 4 GPIO5
5 GPIO2 6 GPIO6
7 GPIO3 8 GPIO7
9 GND 10 +5V
J16: Power Input Connector (Ter inal Blocks 3Px1/5.08 fe ale)
PIN NO.
DESCRIPTION
1 GND EARTH
2 Vin-
3 Vin+
J22: USB Port 3 Connector (1*5 Pin Wafer/2 )
PIN NO.
DESCRIPTION
1 + 5V
2 USB_D3-
3 USB_D3+
4 GND
JP1: CMOS Setup
PIN NO. DESCRIPTION
1-2 Norma (Keep CMOS Setup) ★ Defau t
2-3 C ear CMOS Setup
JP7: GPIO Power Selection
PIN NO. DESCRIPTION
1-2 5V Leve ★ Defau t
2-3 3.3V Leve
JP8: Internal Audio Connector
PIN NO. DESCRIPTION
1 Audio_R+
2 Audio_R-
3 Audio_L+
4 Audio_L-
JP9: LPC Debug Port Pin Assign ent
PIN NO. DESCRIPTION PIN NO. DESCRIPTION

System Installation
WEBS-5491 Embedded System User’s Manual 2-4
1 LAD0 2 3.3V
3 LAD1 4 LPC_RESET
5 LAD2 6 LPC_FRAME
7 LAD3 8 LPC_CLCOK
10 GND

System Installation
WEBS-5491 Embedded System User’s Manual 2-5
JP10: COM2 Pin 9 Function Setup
PIN NO. DESCRIPTION
1-2 3-4 5-6
Short +5V Output
Short RI Function ★ Defau t
Short +12V Output
JP11: COM1 Pin 9 Function Setup
PIN NO. DESCRIPTION
1-2 3-4 5-6
Short +5V Output
Short RI Function ★ Defau t
Short +12V Output
JP12: COM4 Pin 9 Function Setup
PIN NO. DESCRIPTION
1-2 3-4 5-6
Short +5V Output
Short RI Function ★ Defau t
Short +12V Output
JP13: COM3 Pin 9 Function Setup
PIN NO. DESCRIPTION
1-2 3-4 5-6
Short +5V Output
Short RI Function ★ Defau t
Short +12V Output
SW2: AT/ATX & BIOS recovery Setup
PIN NO. DESCRIPTION
1-4(Port1)
ON: AT Mode
OFF:ATX Mode ★ Defau t
2-3(Port2)
ON: Recover BIOS
OFF: Disab e ★ Defau t
*Note: Diagra of SW2 default setting
2.2 Selectable I/O Kit Installation
In addition to default I/O interfaces, including 1x DVI, 2x RS-232/422/485, 4x USB
and 2x Gigabit Ethernet, to further enhance syste flexibility as well as to increase

System Installation
WEBS-5491 Embedded System User’s Manual 2-6
the versatility in application fields, WEBS-5491 allows users to select different I/O
co binations for various arket de ands.
2.3 Memory Installation
WEBS-5491 syste supports one DDR3L SO-DIMM e ory odule. It’s easy to
install by just opening the back cover.
1. Unscrew the back cover to detach it 2. Re ove the IPC back cover
3. Insert Me ory odule to the slot 4. Press down the e ory odule and
finish installation

System Installation
WEBS-5491 Embedded System User’s Manual 2-7
2.4 HDD Installation
WEBS-5491 Series supports 1x 2.5” HDD/SSD. The unique design of the HDD tray
allows easy installation and aintenance. (The height ust be less than 10 )
1. Re ove the screws of HDD tray cover 2. Push the rod to release HDD tray
3. Install the HDD into tray with screws 4. Push HDD tray back into syste
5. Screw the cover and finish installation 6. Inside view of installed HDD in syste
2.5 CF and SD card Installation
CF and SD card are both supported in WEBS-5491 Series. It is easy to install CF and
SD card by opening the cover at side and insert the card.
1. CF cover locates at the right side.
Unscrew and re ove the side bracket.
2. Carefully insert CF and SD card into the
socket.
CF card SD card
3. Co plete insertion (Eject CF card by
pressing the elastic stick on the right side)
4. Screw the side bracket and finish
installation
CF card SD card

System Installation
WEBS-5491 Embedded System User’s Manual 2-8
2.6 Getting Started
WEBS-5491 Series support 12~24V DV input via 3-pin ter inal block connector.
1. Male-type 3-
pin ter inal block connector
located at rear I/O
2. Take the fe ale type 3-
pin ter inal block
connector in accessory kit
3. Fix fe ale type 3-
pin ter inal block
connector to the syste by screw.
4. Follow pin definition and f
ix power cable
to 3-pin ther al block connector by screw
60W AC to DC power adapter and switch cable fro adapter to 3-pin ter inal block
connector is an optional accessory.
1. Screw 3 pin ter inal block cable to
adaptor
2. Connect 3-pin ter inal block
connector to PPC through AC in with
adaptor
2.7 I/O Interfaces
2.7.1 Front View
2. ” HDD/SSD Cover:
Re ove the cover and install the 2.5” HDD/SSD.
*Note: Refer to section 2.4 for installation guide.
Antenna Hole:
It is reserved for WiFi or 3G solution.

System Installation
WEBS-5491 Embedded System User’s Manual 2-9
2.7.2 Rear View
DC in 12-24V via 3-pin Terminal Block Connector:
Provide power connection of Panel PC to the ain power source via DC power cable
or AC/DC adapter.
Power Button:
Press the button to turn ON/OFF the syste .
Reset Button:
Press the button to restart the syste .
Power LED and HDD LED:
It de onstrates the power in and HDD working status of the syste .
Status Power LED HDD LED
Off N/A N/A
Working Green Red
Gigabit Ethernet:
Two Gigabit Ethernet (10/100/1000 Mbits/sec) LAN ports by using dual Intel®
I210IT GbE Ethernet Controller (Support Ju bo Fra e)
USB (Universal Serial Bus) ports:
Connectors for USB-co patible devices
With different I/O
kit combination…
Tota # of
USB ports Detai s
Defau t 4 3x USB 2.0 & 1x USB 3.0
Option 1 2 1x USB 2.0 & 1x USB 3.0
Option 2 4 3x USB 2.0 & 1x USB 3.0
DVI-I:
An external onitor can be provided via DVI-I interface.
COM ports:
Connectors for RS-232/422/485 connection

System Installation
WEBS-5491 Embedded System User’s Manual 2-10
*Note: The RS-232/422/485 configuration is deter ined by BIOS setting. Check BIOS
setting for details.
With different I/O
kit combination…
Tota # of
COM ports Detai s
Defau t 2 2x RS-232/422/485
Option 1 3 2x RS-232/422/485 & 1x RS-232
Option 2 1 1x RS-232/422/485
Line-out:
Connectors for audio line-out
With different I/O
kit combination…
Tota # of
Audio ports Detai s
Defau t 0 N/A
Option 1 0 N/A
Option 2 1 1x Line-out
CF Cover:
Re ove the cover and install the CF card.
*Note: Refer to section 2.5 for installation guide.

BIOS Setup Information
WEBS-5491 Embedded System User’s Manual 3-1
Chapter 3
BIOS Setup Information
WEBS-5491 Series Panel PC adopts PEB-99A4 other board. PEB-99A4 is
equipped with the AMI BIOS stored in Flash ROM. These BIOS has a built-in
Setup progra that allows users to odify the basic syste configuration easily.
This type of infor ation is stored in CMOS RAM so that it is retained during
power-off periods. When syste is turned on, PEB-99A4 co unicates with
peripheral devices and checks its hardware resources against the configuration
infor ation stored in the CMOS e ory. If any error is detected, or the CMOS
para eters need to be initially defined, the diagnostic progra will pro pt the
user to enter the SETUP progra . So e errors are significant enough to abort the
start up.
3.1 Entering Setup—Launch System Setup
Power on the co puter and the syste will start POST (Power On Self Test)
process. When the essage below appears on the screen, press <Del> key will
enter BIOS setup screen.
Press <Del> to enter SETUP
If the essage disappears before responding and still wish to enter Setup, please
restart the syste by turning it OFF and On or pressing the RESET button. It can
be also restarted by pressing <Ctrl>, <Alt>, and <Delete> keys on keyboard
si ultaneously.
Press <F1> to Run General Help or Resume
The BIOS setup progra provides a General Help screen. The enu can be easily
called up fro any enu by pressing <F1>. The Help screen lists all the possible
keys to use and the selections for the highlighted ite . Press <Esc> to exit the
Help screen.

BIOS Setup Information
WEBS-5491 Embedded System User’s Manual 3-2
3.2 Main
Use this enu for basic syste configurations, such as ti e, date etc.
BIOS Information, Memory Information
These ite s show the fir ware and e ory specifications of your syste . Read
only.
System Date
The date for at is <Day>, <Month> <Date> <Year>. Use [＋] or [－] to configure
syste Date.
System Time
The ti e for at is <Hour> <Minute> <Second>. Use [＋] or [－] to configure
syste Ti e.